PN-TPC2W7A User Guide Version – 1
Getting Started Getting Started Introduction to PN-TPC2W7A The PN-TPC2W7A is a full-featured High Definition PC based upon Intel H67® architecture, and powered by an Intel® G620 Pentium® Dualcore CPU. Targeted for Commercial applications such as interactive digital signage, the PN-TPC2W7A has been optimized for reliable operation with Sharp® PN-L series touch-screen displays. The PNTPC2W7A includes the Sharp Pen Software™ application pre-installed on the hard disk.
Getting Started Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Getting Started Specifications Chipset o Intel® H67 Size o Mini-ITX form factor o Case: 7.5 x 7.4 x 1.75 Microprocessor support o Intel® G620 2.
Specifications Specifications (con’t) Onboard Audio o RealTek™ ALC888S High-Definition audio chip o Supports up to 8-channel (2/4/5.1/7.
Installation Mounting PN-TPC2W7A on Sharp PN-L Series Displays 1. Before mounting, make sure to turn off the monitor and remove the AC power. 2. Items needed Sharp PN-L Series TouchScreen Display PN-TPC2W7A Mounting Plate AC Power Adapter 4 x M4 (0.7x10mm) screws 2 x M3 (0.5x5 mm) Phillips® Screw Driver Figure 1 3. Attach the mounting plate There are 8 holes on the mounting plate, but only use 4 holes to match the monitor’s mounting holes depending on the monitor model.
Installation 4. Set the AC power adapter in place Place the AC power adapter into the holder on the right side of the mounting plate as in Figure 3. AC power cord faces downward and the DC power cord to the PN-TPC2W7A faces upward. Figure 3 5.
Installation There are two fingers on the left side of the mounting plate to catch the PN-TPC2W7A in place as shown in Figure 6, and they need to be tightened with two include M3 screws. Figure 6 6. Connect the HDMI video cable and the USB cable prior to turning on the PNTPC2W7A. 7. Finish Plug in the DC power cord into the PN-TPC2W7A’s power connector as in Figure 7.
Installation Rear Connector Layout Audio Port 2-Channel 4-Channel 5.1-Channel Blue Green Pink Orange Black Grey Line-In Line-Out Mic In N/A N/A N/A Line-In Front Speaker Out Mic In Center/Subwoofer Out Rear Speaker Out N/A Audio Port 7.
Installation Rear Connector Layout (con’t) 1. Power Connection (refer to the Rear Connector Layout on pg. 8) Use only the AC power adapter supplied with the system. Input: 100~240V AC 1.3A Output: 12V DC 7A Plug the 12V AC/DC adapter (as in the figure 1 above) to the PNTPC2W7A’s power input jack (as in the figure 2). 2. Power Button This button will stay lit if the PN-TPC2W7A is powered on. If the PN-TPC2W7A doesn’t power up after the AC is connected, then press this button to power up.
Support How to Recover to Factory Installed Condition 1. Before beginning Make sure that all the data including contents and programs you installed are backed up. If you are trying to recover from a bad HDD, please have a qualified technician runs diagnostics and replace defective components. If the unit is under warranty, please contact Sharp Customer Service. 2. Items needed Recovery DVD (comes with the unit) USB DVD Drive 3.
Support Support & RMA Warranty service is available from a Sharp Authorized Service Center located in the United States. To receive repair handling instructions and to find the location of the nearest Sharp Authorized Service Center, please call Sharp toll free at 1-800-BE-SHARP (1-800-237-4277). If it is necessary to ship the Product for servicing, please be sure it is insured and packaged securely.
12
