OPERATION MANUAL PG-M25X Introduction MODEL Setup and Connections Basic Operation Easy to Use Functions DIGITAL MULTIMEDIA PROJECTOR Appendix PG-M25X#E#Hyo1.p65 1 02.4.
IMPORTANT For your assistance in reporting the loss or theft of your Projector, please record the Serial Number located on the bottom of the projector and retain this information. Before recycling the packaging, please be sure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 20. Model No.: PG-M25X Serial No.: This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC.
PG-M25X#Ep00.p65 2 02.4.
SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 13A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted.
Before using the projector, please read this operation manual carefully. Introduction Introduction ENGLISH There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase. 2.
“Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device”. CANADA ONLY For GyroRemote unit (RRMCG1631CESA) This device complies with part 15 of the FCC rules.
Outstanding Features Introduction 1. Image Quality • Superior image quality with Fujinon™ optical lens system. • Newly developed DDR (Double Data Rate) chip eliminates Color Breaking phenomena common with previous generation DLP™ projectors. • Newly developed 12° DMD™ chip provides significantly improved optical efficiency and excellent contrast ratio. 2. Light, Compact, and Unique Slim Design • A new optical engine creates a unique slim design and compact size (4.2 liters, 5.8 lbs. (2.6 kg)). 3.
6. Built-in PCMCIA card slot (Type II) • Wireless presentations using a wireless LAN PC card. Supports the global wireless LAN standard, IEEE802.11b. This wireless LAN PC card complies with IEEE802.11b wireless LAN standards. Computers with built-in wireless LAN PC cards that support this standard allow for wireless connections. Note • A wireless connection with all IEEE802.11b compliant computers is not guaranteed.
Contents Outstanding Features ......................................... 3 Contents ............................................................... 5 IMPORTANT SAFEGUARDS ............................... 8 How to Access the PDF Operation Manuals (Windows, Macintosh) ................................. 13 Part Names ........................................................ 14 Projector (Front and Top View) ................................ 14 Projector (Side View) ..............................................
Network Settings ............................................... 69 Setting Up a Projector Name ................................... 69 Setting the IP Address ............................................. 70 Setting the Wireless Channel ................................... 71 Setting the SSID ...................................................... 72 Setting the DHCP Server ......................................... 73 Resetting the Network Settings .............................. 74 Capturing the Image .......
Introduction Wireless LAN PC Card Specification ............ 120 Usable Cards and Their Capacity .................. 121 Dimensions ...................................................... 122 Glossary ........................................................... 123 Index ................................................................. 125 -7 PG-M25X#E#p01_07.p65 7 02.4.
IMPORTANT SAFEGUARDS CAUTION: Please read all of these instructions before you operate this product and save these instructions for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 11.
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating instructions.
IMPORTANT SAFEGUARDS (cont.) INTELLECTUAL PROPERTY RIGHTS IMPORTANT READ BEFORE USING THE PRODUCT • You have acquired a product that includes software licensed to SHARP Corporation by Lineo, Inc. (“Lineo”). The Software is protected by copyright laws, international copyright treaties, and other intellectual property laws and treaties.
Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for a replacement. See “Replacing the Lamp” on page 71. Do not subject the projector to hard impact and/or vibration. ■ Take care with the lens so as not to hit or damage the surface of the lens. Rest your eyes occasionally.
IMPORTANT SAFEGUARDS (cont.) Other connected equipment ■ When connecting a computer or other audiovisual equipment to the projector, make the connections AFTER turning off the projector and the equipment to be connected. ■ Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.
PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector, even if you do not have this manual on hand. To utilize these manuals, you need to install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet, you can install it from the CD-ROM. To Install Acrobat Reader from the CD-ROM For Windows: 1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon.
Part Names Numbers in refer to the main pages in this Operation Manual where the topic is explained. Projector (Front and Top View) 110 TEMPERATURE 110 LAMP replacement indicator warning indicator Illuminates in green normally. Replace the lamp when the indicator illuminates in red. POWER indicator Illuminates in green normally. When the internal temperature rises, this indicator will illuminate in red. 110 Illuminates in red, when the projector is in standby.
Introduction Projector (Side View) 47 USB terminal For connecting a computer using a USB cable. 27 INPUT 1 terminal Shared audio terminal for INPUT 1, INPUT 2, INPUT 3 and INPUT 4. 27 Port for DVI digital, computer RGB, and COMPONENT signals. INPUT AUDIO terminal 30 INPUT 3 terminal For connecting video equipment. 30 INPUT 2 terminal Terminal for connecting video equipment with an S-VIDEO terminal.
Part Names (cont.) GyroRemote Front Function 1 / 2 buttons For specifying the button assignments for Function 1 and Function 2 INPUT button For switching between inputs 1,2,3 and 4. L-CLICK/ ENTER button For entering menu items or to perform a left click when using the wireless mouse. POWER button 42 LED indicator 44 POINTER button 48 R-CLICK / UNDO button 54 MENU button 35 VOLUME buttons 40 35 48 49 For turning the power on or off.
Inserting the Batteries Introduction The batteries (four R03 batteries (“AAA” size, UM/ SUM-4, HP-16 or similar)) are included in the package. 1 Slide the cover in the direction of the arrow to open it. 2 Insert the included batteries. Tapes for removing the batteries • Insert the batteries making sure the poand larities correctly match the marks inside the battery compartment.
The GyroRemote GyroRemote Features This projector uses the GyroRemote technology, that allows for the following features when compared to ordinary infrared remote controls. Operation Range: Area up to a 15 m RF Technology With ordinary remote controls, the operation range is limited because of directivity; they cannot operate if there are objects between the projector and the remote. The GyroRemote can operate up to a range of 15 m (49.2 feet) by sending RF signals to the projector.
If there are any extreme temperature changes when the GyroRemote is being used or after batteries have been replaced, the mouse cursor or pointer may continue to move by itself even if no action has been performed. In this case, calibrate the GyroRemote using the following procedure. 1 Double click on the rear of the GyroRemote. 2 Make sure that the LED indicator is lit, and place the GyroRemote on a leveled location.
Accessories Supplied accessories GyroRemote (1) For U.S., Canada, etc. RRMCG1631CESA (2) For Europe, Australia, Oceania and Asia RRMCG1653CESA Four R03 batteries (“AAA” size, UM/SUM-4, HP-16 or similar) Power cord (6' (1.8m)) (1) (2) For U.S., Canada, etc. QACCDA007WJPZ (4) (3) For Europe, except U.K. QACCV4002CEZZ For Australia, New Zealand and Oceania QACCL3022CEZZ For U.K., Hong Kong and Singapore QACCB5024CENA Note • Depending on the region, projectors only ship with one power cord (see above).
Setup and Connections Setup and Connections PG-M25X#E#p21_32.p65 21 02.4.
Setup Foot releases Adjustment feet Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet when the surface of the projector is placed on is uneven or when the screen is slanted. The projection of the image can be made higher by adjusting the projector when it is in a location lower than the screen. 1 Press the foot releases. 2 Lift the projector to adjust its height and remove your hands from the foot releases.
Setting up the Screen Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image. Note Standard Setup (Front Projection) ■ Place the projector at the required distance from the screen according to the desired picture size. (See page 24.) Example of Standard Setup • The distance from the screen to the projec- Side View tor may vary depending on the size of the screen. P.
Setup (cont.) Screen Size and Projection Distance Screen Base line: Horizontal line passing through the lens center. Lens center 90° H L:Projection distance NORMAL Mode (4:3) Picture (Screen) size Diag. (X) Width Projection distance (L) Height Maximum (L1) Minimum (L2) – Distance from the lens center to the bottom of the image (H) 300" (762 cm) 240" (610 cm) 180" (457 cm) 39' 5" (12.0 m) 0" (0.0 cm) 250" (635 cm) 200" (508 cm) 150" (381 cm) 39' 8" (12.1 m) 32' 10" (10.0 m) 0" (0.
Projecting a Reversed/Inverted Image Projection from behind the screen ■ Place a translucent screen between the projector and the audience. ■ Reverse the image by setting “Rear” in “PRJ Mode”. See page 98 for use of this function. When using the default setting. ▼On-screen Display Setup and Connections Projection using a mirror ■ Place a mirror (normal flat type) in front of the lens. ■ Reverse the image by setting “Rear” in “PRJ Mode”, when the mirror is placed on the audience side.
Connecting the Projector to Other Devices Before Connecting Note • Before connecting, be sure to turn off both the projector and the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that the computer is the last device to be turned on after all the connections are made. • Be sure to read the operation manuals of the devices to be connected before making connections.
Connecting the Projector to a Computer Connecting to a Computer Using the DVI to 15-pin D-sub Cable DVI to 15-pin D-sub cable To RGB Output port To Audio Output port Connect the projector to the computer using the supplied DVI to 15-pin D-sub cable. Setup and Connections 1 Supplied accessory Notebook computer • Secure the connectors by tightening the thumbscrews. 2 To input audio signal, connect the projector to the computer using a ø3.
Connecting the Projector to Other Devices (cont.) Connecting to a Computer Using a DVI Cable (Sold Separately) This projector comes installed with a DVI digital input terminal in which computer digital image signals can be directly input. 1 Connect the projector to the computer using the DVI cable. 2 To input audio signal, connect the projector to the computer using a ø3.5 mm stereo audio cable (commercially available or available as Sharp service part QCNW-4870CEZZ).
Connecting to Video Equipment Connecting to Component Video Equipment Optional accessories DVI to 15-pin D-sub adaptor Model: AN-A1DV (7.9" (20 cm)) *DTV is the umbrella term used to describe the new digital television system in the United States. 1 2 Connect the 3 RCA to 15-pin Dsub cable using the DVI to 15pin D-sub adaptor.
Connecting the Projector to Other Devices (cont.) Connecting to Video Equipment Using an S-VIDEO, a Composite Video or an Audio Cable Using an S-VIDEO, video, or audio cable, a VCR, laser disc player or other audio-visual equipment can be connected to INPUT 2, INPUT 3 and AUDIO terminals. 1 2 Connect the projector to the video equipment using a ø3,5 mm to RCA S-VIDEO cable or a composite video cable (both commercially available).
Installing / Removing the PC Card Eject button Installing the PC Card in to INPUT 4 Terminal Insert a PC card such as a wireless LAN card or memory card as shown on the right. Setup and Connections Info • We recommend that you recess the Eject button before inserting the PC card. This will prevent accidental ejection during operation. The notch Make sure that the Eject button is not out, and that the notch on the card is to the left, when installing the card.
Connecting the Projector to Other Devices (cont.) Connecting to a Monitor Watching Images on Both the Projector and a Monitor You can display computer images on both the projector and a separate monitor using an RGB monitor loop-out adaptor and an RGB cable. RGB monitor loop-out adaptor Type: AN-A1MY (7.
Basic Operation Basic Operation PG-M25X#E#p33_49.p65 33 02.4.
Image Projection ▼Projector indicators Basic Procedure Connect the required external equipment to the projector before operating the following procedures. Details are found in the projector operation manual. LAMP REPLACEMENT indicator POWER indicator Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 37. 1 Plug the power cord into the wall outlet.
4 "On-screen Display (Example) Press mode. and select the input INPUT 1 Mode INPUT 2 Mode • Each press switches in the following order’ → INPUT 1 → INPUT 2 → INPUT 3 → INPUT 4 • You can also use the GyroRemote. on the Using DVI digital Note Using S-Video INPUT 3 Mode • When no signal is received, “NO SIGNAL” will be displayed. When a signal that the projector is not preset to receive is received, “NOT REG.” will be displayed.
Image Projection (cont.) 6 Press on the projector to temporarily turn off the picture and sound. Note • Pressing again will turn the picture and the sound back on. • When using the GyroRemote, you can select AV MUTE using the Button Assign function (see page 41.) • If you want to temporarily mute the sound, select MUTE using the Button Assign function (see page 41.) 7 Press on the projector or on the GyroRemote. When the confirmation screen or is displayed, press once again.
Selecting the On-screen Display Language • The on-screen display language of the projector can be set to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japanese. • The following explanation uses operations from the projector as example. 1 Press 2 Press or “Language”. 3 Press or to select the desired language, and then . press 4 Press . • The menu will be displayed. to select .
Correcting the Trapezoidal Distortion (Keystone Correction) Correcting the Trapezoidal Distortion This function allows for Keystone (On-screen Trapezoidal Distortion) Correction. The following explanation uses operations from the projector as example. LENS button Adjustment buttons ("'\ |) Note • Keystone Correction is the correction for trapezoidal distortion that occurs when the image is positioned away from the center axis of the screen.
3 Press . Note • You can use the same settings used in NORMAL mode 4:3 for 16:9. • Straight lines or the edges of images may appear jagged while adjusting the image. • The Digital Shift function is displayed when a wide screen from video or digital video is displayed. Digital Shift Setting For easier viewing, this function shifts the image projected on the screen up or down eliminating either the upper or lower black band found in 16:9 and other wide aspect ratios.
Using the GyroRemote Before Using the GyroRemote Make sure that the antenna on the projector is fully extended before operating the projector with the GyroRemote. Info • The control range under actual operating conditions may be less than optimum depending on where the projector is placed and the radio signal environment. • If the GyroRemote does not operate, press on the GyroRemote.
Function Assign Function 1 button The Button Assign function on the GyroRemote, consists of 5 items (1/5 to 5/5) and within each, there are 4 function buttons (Function 1 to 4.) Selecting the function buttons for assigning items is done via the projector. 1 ASSIGN button on the GyroRemote. • Each time you press the Button Assign selection changes as shown below.
Using the GyroRemote (cont.) LED indicator GyroRemote Channel Setting The GyroRemote uses radio signals, which can receive interference under certain conditions. To avoid interference, when using multiple GyroRemotes, register a different channel for each GyroRemote in the projector. The GyroRemote has 8 channels for U.S., Canada, etc. and 4 channels for Europe, Australia, Oceania and Aisa. 1 RF CH+ button Press located on the GyroRemote.
3 Press on the GyroRemote you want to register. • The LED indicator on the GyroRemote lights up. • “Register” is displayed at the bottom of the screen for a few seconds and registration starts. When storing is complete, “Learn Mode” is displayed. LED indicator TEACH button Note • If no action is taken for more than 5 minutes, the projector exits from the Learn mode. Register 4 Press • This completes the Registration mode.
Using the Presentation Tools The GyroRemote is equipped with the following presentation tools. These are very useful when emphasizing a main point during the presentation. • Pointer function • Stamp function • Line function LED lamp Function 1 button Using the Pointer Using the GyroRemote. For details see page 40. 1 ENTER button Function 3 button Hold the GyroRemote and . move it while pressing • The pointer moves in accordance with the GyroRemote’s movements. is • The pointer disappears when released.
Using the Stamp Function Using the GyroRemote For details see page 40. 1 Press on the GyroRemote and then select “Button Assign 1/5”. • The assign function is displayed at the bottom right of the screen. 2 Press on the GyroRemote. • The stamp type will change every time is pressed, as shown on the right. Press on the GyroRemote to select the color. • The stamp color will change every time is pressed, as shown on the right.
Using the Presentation Tools (cont.) Using the Line Function Using the GyroRemote, you can draw on the screen various shapes such as squares, ovals, horizontal, vertical, perpendicular and freestyle lines. Using the GyroRemote, For details see page 40. 1 Press on the GyroRemote and then select “Button Assign 1/5”. • The assign function is displayed at the bottom right of the screen. 2 3 Press on the GyroRemote.
Using the Wireless Presentation Function of the GyroRemote The remote control can perform mouse operations on a computer screen displayed on the actual screen. The remote control can also be used as a pointer. (See page 44) Connecting the Computer and the Projector 1 Connect the projector to the computer using the supplied USB cable. Supplied accessory USB cable USB port Notebook computer Note • This function only wor ks with Microsoft Windows OS and Mac OS.
Using the Wireless Presentation Function of the GyroRemote (Cont.) Using as a Wireless Mouse 1 2 Move the GyroRemote while . The LED holding down indicator is lit. L-CLICK button LED indicator R-CLICK button GYRO ACTIVE button Press or . It functions the same as the buttons of a mouse connected to the computer. • In the case of one mouse button (such as on a Macintosh) clicking this button will function the same as either and .
Turning Off the GyroRemote Make sure to turn off the GyroRemote to prevent any unwanted operations, when not using the projector. This also prevents consumption of batteries set in the GyroRemote. 1 Press and located inside the lower cover on the GyroRemote at the same time for more than 2 seconds. TEACH button • The LED Indicator will flash 3 times and the GyroRemote will turn off. Any buttons pressed after (excluding ) will not emit signals.
Using the Menu Screen This projector has three sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or GyroRemote using the following procedure. On-screen menu for INPUT 1 RGB mode On-screen menu for INPUT 2 or INPUT 3 Mode Menu Bar (Main Menu) Menu Bar (Main Menu) On-screen menu for INPUT 4 RGB mode Menu Bar (Main Menu) MENU button Menu Selections on the Projector (Adjustments) 1 Press Adjustment buttons ("'\ |) .
2 Press or to select the menu you want to adjust. Note • For details on the menus, see the tree charts on pages 56 and 58. • When using the GyroRemote to move through a menu, see page 54. 3 Press or to select the item you want to adjust. Note • To display a single adjustment item, after selecting the item. press Only the menu bar and the selected adjustment item will be displayed. or , Then if you press the following item (“Phase” is after “Clock”) will be displayed.
Using the Menu Screen (cont.) Menu Selections on the projector (Settings) 1 Press . • The menu screen is displayed. MENU button Adjustment buttons ("'\ |) Note • The “Picture” menu screen is displayed in inputs 1, 2 and 3 and the “Card” menu screen is displayed in INPUT 4 mode. • The on-screen display shown on the right is displayed when the INPUT 1 mode is selected. 2 Press or to select the menu you want to adjust.
4 Press . • The cursor shifts to the sub menu. Sub menu Press or to select the setting of the item displayed in the sub menu. 6 Press Basic Operation 5 . • The item selected is set. Note • Some adjustment items will display a confirmation message. When setting an item, press or to select “Yes” or “OK” and then press 7 Press . . • The menu will disappear and the adjustment is stored. -53 PG-M25X#E#p50_64.p65 53 02.4.
Using the Menu Screen (cont.) Using the GyroRemote to Navigate the On-screen Menu (Adjustments) 1 Press . • The menu screen is displayed. Note • The “Picture” menu screen is displayed in inputs 1, 2 and 3 and the “Memory Card” menu screen is displayed in INPUT 4 mode. • The screen on the right shows the INPUT 1 mode screen. 2 MENU button 1 While holding down , move the GyroRemote left and right to select the menu.
Using the GyroRemote to Navigate the Onscreen Menu (Settings) 1 Press MENU button . • The menu screen is displayed. Note • The “Picture” menu screen is displayed in inputs 1, 2 and 3 and the “Memory Card” menu screen is displayed in INPUT 4 mode. • The screen on the right shows the INPUT 1 mode screen. 2 On-screen menu for INPUT 1 mode Menu Bar (Main Menu) 1 While holding down , move the GyroRemote left and right to select the menu.
Menu Bar Items This list shows the items that can be set in the projector.
■ INPUT 2 / 3 Mode Main menu Sub menu Main menu Sub menu Picture Contrast –30 +30 Options (2) Lamp Timer Page 59 Bright –30 +30 Page 96 Break Timer Color –30 +30 Tint –30 +30 Sharp –30 +30 Red –30 +30 Blue –30 +30 CLR Temp –3 PRJ Mode Register R/C +3 Keylock Level Normal Level A Level B Password Old Password New Password Reconfirm Anti-Theft Old Code New Code Reconfirm Reset Progressive Mode 2D Progressive 3D Progressive Film Mode Front Ceiling + Front Rear Ceilin
Menu Bar Items (cont.) This list shows the items that can be set in the projector.
Adjusting the Picture You can adjust the projector’s picture to your preferences with the following picture settings.
Adjusting the Picture (cont.) Progressive Mode This function allows you to select the progressive display of a video signal. The progressive display projects a smoother video image. Select “Progressive Mode” in the “Picture” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • 2D Progressive This function is useful to display fast-moving images such as sports and action films.
Adjusting Computer Images Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen. Selected Item Description Clock Adjusts vertical noise. Phase Adjusts horizontal noise (similar to tracking on your VCR). H-Pos Centers the on-screen image by moving it to the left or right. V-Pos Centers the on-screen image by moving it up or down.
Adjusting Computer Images (cont.) Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Select “Select Setting” in the “Fine Sync” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • If a memory position has not been set, a resolution and frequency setting will not be displayed.
Checking the Input Signal This function allows you to check the current input signal information. Select “Signal Info” in the “Fine Sync” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • The projector will display the number of scanned lines available input from audiovisual equipment such as a DVD player or Digital Video. Auto Sync Adjustment Used to automatically adjust a computer image.
Adjusting Computer Images (cont.) Auto Sync Display Function Used to set the screen displayed during Auto Sync. Select “Auto Sync” in the “Fine Sync” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • • .....The image set as a background image is projected. ..... The computer image being adjusted is displayed. -64 -64 PG-M25X#E#p50_64.p65 64 02.4.
Easy to Use Functions Easy to Use Functions PG-M25X#E#p65_77.p65 65 02.4.
Using the Network Before setting the network This section explains items that can be set in a network. A wireless connection will not be possible if these items are not set correctly. Also, as there are values that must be entered in a pre-configured network, make sure to consult with your network administrator. IP Address ■ When What is an IP Address? The IP Address is a number for identifying devices connected to the network. An IP address must be assigned to each device using network values.
Wireless Channels ■ What is a wireless channel? A wireless channel is a frequency used by wireless LAN cards when communicating. 14 channels can be used. If other wireless LAN networks are being used near the location where the projector is, make sure that different channels have been set to avoid interference. 11ch 6 ch 1ch ■ Assigned wireless channels If there are no other networks that can cause interference nearby, set either 1, 6, 13, or 14. The wireless channel set in the projector is 192.168.0.
Using a Wireless LAN PC Card Inserting a wireless LAN PC card into the INPUT 4 slot on the projector allows you to send images to the projector and project them via a wireless connection. Installing a Wireless LAN PC Card 1 Insert the wireless LAN PC card into the INPUT 4 slot on the projector. • For details on how to install the card, see page 31. • When the card is inserted, the input will automatically change to INPUT 4. Note • See page 75 when installing a memory card in the projector.
Network Settings Note • This section explains items that can be set in a network. A wireless connection will not be possible if these items are not set correctly. • Also, as there are values that must be entered in a pre-configured network, make sure to consult with your network administrator. Setting Up a Projector Name This Network setting assigns a name to the projector. The default setting is “MY PROJECTOR”.
Network Settings (cont.) 5 Repeat steps 3 and 4 to enter the remaining characters you want. Note • A maximum of 16 characters can be entered 6 Press . • The settings are stored and active. Setting the IP Address Set the IP Address of the projector. Set “TCP/IP” in the network menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. 1 Press or to select TCP/IP and then press .
5 Repeat steps 3 and 4 to set all the digits. Setting the Gateway Select “Gateway” using the procedure in step 1, and enter the values by repeating the procedure in step 3 and 4. Setting the Subnet Mask Select “Subnet Mask” using the procedure in step 1, and enter the values by repeating the procedure in step 3 and 4. 6 Press Setting the Wireless Channel Set the wireless LAN channel so that no interference occurs with another wireless channel.
Network Settings (cont.) Setting the SSID Set the projector’s SSID. The default setting is “SHARP_PRJ”. Select “Wireless LAN” in the network menu on the menu screen ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. 1 Press or to select . “Wireless LAN” and then press 2 Press or to select “SS ID” and then press 3 . Press or to select the characters you want to set.
Setting the DHCP Server This function is set when using the DHCP server on the projector. Set “DHCP Server” in the network menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Enabling the DHCP server function Set the “Server” in the submenu to “ON”. Set the “Server” to “OFF” when not using the DHCP server function.
Network Settings (cont.) Resetting the Network Settings This will return the default values of the Network Settings. Select “Reset” in the Network menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Wireless LAN PC card: Troubleshooting Check the following if you cannot connect to the network using your wireless LAN PC card. 1.
Using a Memory Card When a memory card is installed, images stored in the memory card can be projected. If presentation files are stored in the memory card you can make presentations using only the projector and the memory card, without having to use a computer. Displaying of the Contents in the Card as an Index 1 Insert the memory card into the INPUT 4 terminal on the projector. • For details on installing the card, see page 31.
Using a Memory Card (cont.) 2 Remove the card. • Remove the card after the message is displayed. • For details on how to remove the card, see page 31. Info • When moving the projector, make sure that the Eject button is pressed all the way in. If moved with the Eject button out, the projector may be damaged. Setting the Thumbnail Display You can display JPEG files and slide show VQ files as thumbnails. Some files may not be displayed as thumbnails.
Setting Lists You can display files in lists. For list settings, see page 78. Moving files • Press or select the folder and press to . • To move the folder up one level, select and press . Projecting a file • Press or or select the folder and press to . • The selected image is displayed. Changing the page displayed • Select or and press . Easy to Use Functions -77 PG-M25X#E#p65_77.p65 77 02.4.
Memory Card Settings Setting Files You can limit the files displayed in the Index mode according to their type. Select “Display File” in the Memory Card menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • All Files All the files and folders are displayed. • Image File Only images files and folders are displayed. The types of images files that can be displayed are as follows: JPEG, VQ, TIFF, BMP.
Setting the Display Format of the Index Mode Select “View” in the Memory Card menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • Thumbnail display For displaying the contents of the memory card as thumbnails. • List display For displaying the contents of the memory card in a list.
Memory Card Settings (cont.) Setting the Display Interval for Image Files You can set the display interval for slide show files (image files). Adjust “Interval” in the Memory Card menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Pressing the button during image protection via the Autorun function will display the submenu. • “Next” ............... Proceeds to the next page. • “Previous” ........
Displaying a Still Image This function allows you to instantly freeze a moving image. This is useful when you want to display a still image from a computer or video, giving you more time to explain the image to the audience. Storing an Image in Still Image Format For using the GyroRemote, see page 40 for details. 1 • The Assign function is displayed at the bottom right of the screen. 2 Press ASSIGN button . • The image currently being projected becomes a still image.
Selecting the Picture Display Mode This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “FULL”, “DOT BY DOT”, “BORDER”, “STRETCH” or “SMART STRETCH” image. Switching the Picture Display Using Different Input Signals For using the GyroRemote, see page 40 for details. 1 Press to display “Button Assign 4/5”. • The Assign function is displayed at the bottom right of the screen. 2 Press .
COMPUTER NORMAL 1024 × 768 1024 × 768 1024 × 768 1024 × 768 960 × 768 SVGA (800 × 600) XGA (1024 × 768) SXGA (1280 × 960) UXGA (1600 × 1200) SXGA (1280 × 1024) 4:3 aspect ratio Other aspect ratios FULL — — — — 1024 × 768 DOT BY DOT 800 × 600 — 1280 × 960 1600 × 1200 1280 × 1024 • When XGA (1024 x 768) signals have been entered or when using INPUT 4 Mode, they will be fixed as NORMAL.
Selecting the Picture Display Mode (cont.) This function allows you to enlarge a specific portion of an image. This is useful when you want to display a detailed portion of the image. Displaying an Enlarged Portion of an Image For using the GyroRemote, see page 40 for details. 1 Press to display “Button Assign 3/5”. • The Assign function is displayed at the bottom right of the screen. 2 Press Function Button enlarge the image.
4 Press to cancel the operation, then the magnification returns to ×1. Note • In the following cases, the enlarged image will return to its original size (×1). • When switching the input. • When (undo) has been pressed. • When the input signal has been changed. • When the input signal resolution or refresh rate (vertical frequency) has been changed. Easy to Use Functions -85 PG-M25X#E#p78_96.p65 85 02.4.
Gamma Correction Function Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the brightness of the brighter portions. When you are displaying images with frequent dark scenes, such as a film or concert, or when you are displaying images in a bright room, this feature makes the dark scenes easier to see and gives the impression of greater depth in the image.
Selecting the Power Save Mode The Power Save Mode or the Automatic Power Shutoff function allows you to reduce the power consumption of the projector. Setting the Power Save Mode Select “Power Save” in the “Options (1)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Description of Power Save Modes Quantity of light is 80%. Power consumption is XXXW. Quantity of light is 100%. Power consumption is 295W.
Displaying Dual Pictures (Pict in Pict) Picture in Picture function allows you to display two pictures on the same screen. You can display the image input from INPUT 2 or 3 as an inset picture overlapping the main picture from INPUT 1. (This function can only be set in the RGB menu.) Displaying the Inset Picture Select “Pict in Pict” in the “Options (1)” menu on the menu screen. Make sure to operate when INPUT 1, INPUT 2 and INPUT 3 all have signals. ➝ For operating the menu screen, see pages 50 and 52.
4 Press ture. to move the inset pic- • The inset picture will be moved to the inset picture frame. Note • The inset picture can only be displayed with composite video (NTSC/PAL/ SECAM) or S-Video signal. • The Freeze function works only with the inset picture, when the Pict in Pict mode is in operation. When the signal entered into INPUT 1 is as follows, Pict in Pict does not work: • With a resolution that exceeds SXGA. • When the input signal is 480I , 480P, 720P or 1080I.
Activating the sRGB Color Management Function This function calibrates the projector’s output to confirm to sRGB standard (6,500K). Setting the Color Management Function (sRGB) Select “sRGB” in the “Options (1)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • For additional information about sRGB function, please visit “http://www.srgb.com/”.
Auto Search Function This function automatically searches for and switches to the input mode in which signals are being received, when the projector is turned on, or when the INPUT button is pressed. This function does not work with INPUT 4 mode. Using Auto Search Select “Auto Search” in the “Options (1)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55.
Video Digital Noise Reduction (DNR) System Video Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise. Reducing Image Noise Select “DNR” in the “Options (1)” menu. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • Set a level so as to view a clearer picture. Make sure to set DNR to “OFF” in the following cases: • When the image is blurry.
Setting the Video Signal The video input system mode is preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the video signal difference. In that case, switch the video signal. Setting the Video Signal Select “Video System” in the “Options (1)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55.
Saving Projected Images • This projector allows you to capture projected images (RGB signals) and set them as a startup image, or background image when no signals are being received. • You can capture the images that are input using analog RGB signals and Digital RGB XGA signals. Capturing the Image Select “Image Capture” in the “Options (1)” menu on the menu screen ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55.
Setting a Background Image This function allows you to select the image displayed when no signal is being sent to the projector. Selected Item Description Sharp SHARP default image Custom *1 User customized image (i.e. company logo) Blue Blue screen None Black screen *2 *1 You can set a captured image as a background image by selecting “Custom”. *2 If the input signal has interference, the screen will be displayed with the interference.
Using an RGB Monitor Loop-out Adaptor Using an RGB monitor loop-out adaptor (sold separately) and an RGB cable (commercially available), be sure to set to “ Yes (Y Cable)” when you want to display computer images both on the projector and on a monitor. Using an RGB Monitor Loop-out Adaptor Select “Monitor Out” in the “Options (1)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55.
Displaying the Break Timer Displaying and Setting the Break Timer Select “Break Timer” from the “Options (2)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. 1 "On-screen Display When “ ” is displayed, press or to set the Break Timer. • You can set anywhere between 1 and 60 minutes (in 1 minute units).
Reversing/Inverting Projected Images This projector is equipped with a reserve/invert image function that allows you to reverse or invert the projected image for various applications. Selected Item Description Front Normal image Ceiling + Front Inverted image Rear Reversed image Ceiling + Rear Reversed and inverted image Setting the Projection Mode Select “PRJ Mode” in the “Options (2)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52.
Locking the Operation Buttons on the Projector This function can be used to lock the use of certain operation buttons on the projector. The following are the three keylock levels. Keylock Level Description Normal All operation buttons are functional. Level A Only INPUT/VOLUME/AV MUTE buttons on the projector are available. Level B All operation buttons on the projector are unavailable. Setting up the Keylock Select “Keylock Level” in the “Options (2)” menu on the menu screen.
Setting up a Password A password can be set by the user to prevent adjustments to certain settings on the “Options (2)” menu. Using a password together with the Keylock Level (page 99) is more effective. Entering the Password Select “Password” in the “Options (2)” menu on the menu screen ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. 1 Press or to select the desired number and then press 2 .
Changing the Password Select “Password” in the “Options (2)” menu on the menu screen ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. 1 Press , and to enter the password in “Old Password” and press 2 Press , and . to set the new password and press 3 . Enter the new 4-digit password again in “Reconfirm” and press .
Setting the Anti-Theft Setting the anti-theft function will disable any projection of images even if signals are sent to the projector. A keycode is necessary to release the system lock. Make sure to remember the key code you set. Info If the keycode is not correctly entered in the key code field, only the key code screen will be displayed and no other operations will be possible. Repairing the system lock even within the period of guarantee will incur reparation costs.
2 Enter the remaining 3 digits in the same way as above and press 3 . Re-enter the same key code in Reconfirm and press . Note • The Keylock function will become temporarily disabled. When “Anti-Theft” is set, the keycode inputting section appears after the power is turned on. At that time, enter the right keycode. • Press the buttons on the remote control if the buttons on the remote control are used for setting the keycode.
Setting the Anti-Theft (cont.) Changing the Keycode • When “Anti-Theft” is selected and a password has been entered, the password input box is displayed. After the password has been entered, you can change the keycode. Select “Anti-Theft” in the “Options (2)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55.
Initializing the Settings This function allows you to initialize the settings you have made in the projector. Returning to the Default Settings Select “All Reset” in the “Options (2)” menu on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. Note • If a password has been set, the password input box will be displayed when selecting “All Reset”. Easy to Use Functions The following items cannot be initialized.
Displaying the Adjustment Settings This function can be used to display all the adjusted settings as a list on the screen. Overview of ALL Menu Settings Select the “Status” menu and press on the menu screen. ➝ For operating the menu screen, see pages 50 and 52. ➝ For operating the menu screen using the GyroRemote see pages 54 and 55. -106 -106 PG-M25X#E#p97_106.p65 106 02.4.
Appendix Appendix PG-M25X#E#p107_115.p65 107 02.4.
Carrying the Projector How to Use the Carrying Case When transporting the projector, make sure to retract the antenna, cover the lens with the lens cap, and place the projector in the included carrying case. 1 Open the cover of the carrying case. 2 Remove the inner padding from the carrying case, and fold it in the direction of the arrows. 3 Reinsert the inner padding into the carrying case. Info • Be sure to insert the inner padding to protect the lens and the projector.
Maintenance Cleaning the projector Cleaning the lens ■ Be sure to unplug the power cord before cleaning the projector. ■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet. ■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items on the projector for long time. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.
Maintenance Indicators ■ The warning lights on the projector indicate problems inside the projector. ■ If a problem occurs, either the TEMPERATURE WARNING indicator or the LAMP REPLACEMENT indicator will illuminate red, and the power will turn off. After the power has been turned off, follow the procedures given below.
Regarding the Lamp Lamp ■ It is recommended that the lamp (sold separately) be replaced after approximately 1,900 cumulative hours of use or when you notice a significant deterioration of the picture and color quality. The lamp usage time can be checked with the on-screen display. See page 58. ■ For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service Center. IMPORTANT NOTE TO U.S.
Regarding the Lamp (cont.) Removing and Installing the Lamp Unit Lamp unit BQC-PGM20X//1 Info • Be sure to remove the lamp unit by the handle. Be sure not to touch the glass surface of the lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below. • Do not loosen other screws except for the lamp cover and lamp unit. • Please refer to the installation manual included with the lamp unit.
4 Loosen the lamp unit. 5 Insert the new lamp unit. 6 • Remove the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. Securing screw Attach the lamp unit cover. • Slide the lamp unit cover in the direction of the arrow. Then tighten the user service screw.
Connecting Pin Assignments DVI Digital / Analog INPUT 1 port : 29 pin connector • DVI Digital INPUT 9 ••••••••• 1 2 •••• Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ~ • • • • • • • • • 16 ~ •••• 7 8 C1 C2 C4 C5 C3 17 24 18 •••• ~ • • • • 23 • DVI Analog RGB Input Pin No.
Computer Compatibility Chart • Multiple signal support Horizontal Frequency: 15–126 kHz Vertical Frequency: 43–200 Hz* Pixel Clock: 12–230 MHz • Compatible with sync on green and composite sync signals • UXGA and SXGA compatible in advanced intelligent compression • AICS (Advanced Intelligent Compression and Expansion System) resizing technology The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.
Troubleshooting Problem Check • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. • The selected input mode is wrong. • Cables incorrectly connected to side panel of the projector. • Remote control batteries have run out. • External output has not been set when connecting notebook computer. • The AV MUTE display appears. • The cover of the lamp unit is not installed correctly. • Cables incorrectly connected to the side panel of the projector.
Problem The power cannot be turned on or off using the POWER button on the projector. The screen turns green when using the INPUT 1 component. The screen turn pink when using the INPUT 1 RGB mode. The card installed in the INPUT 4 terminal cannot be recognized. “Not supported” is displayed. Picture is dark Picture is too bright and whitish The VOLUME buttons on the projector do not work Check • The key lock level is set. • If level B has been set, none of the buttons will work.
For SHARP Assistance If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 76 and 77. If this operation manual does not answer your question, please contact the SHARP Service departments listed below. U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharplcd.com Canada Sharp Electronics of Canada Ltd. (905) 568-7140 http://www.sharp.
Specifications This SHARP projector uses a DMD panel. This very sophisticated panel contains 786,432 pixels. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Wireless LAN PC Card Specification Product Name 11 Mbps Wireless LAN PC Card Model Number AN-WC11B Host Interface PCMCIA TYPE II Dimensions 4 1⁄2" × 2 1⁄8" × 1⁄4" (115 × 54 × 7 mm) Weight 40 g Frequency Band 2.412 – 2.462 GHz (Central frequency) Number of Channel Channels that can be used vary depending on the country. Operating Voltage 3.3 V ± 5% or 5 V ± 5% Current Consumption Typ. 240 mA, Max. 300 mA Spreading DS SS (Direct Sequence Spread Spectrum) Data rate 11 Mbps, 5.
Usable Cards and Their Capacity 1. JPEG images that are DCF compliant *1 and are stored in a memory card such as those from a digital camera, can be displayed in the projector when using the Card mode. For details on the Card Mode, see page XX. 2. The memory cards in the following table (commercially available) can be used. Memory Card *2 Flash ATA card SD memory card CompactFlash Multimedia card Smart media Memory stick Memory card capacity under 128MB can be used. under 128MB can be used.
Dimensions Units: inches (mm) Rear View Side View Top View 12 1/16 (306.5) Side View 11 13/16 (303) 8 3/4 (223) 27 1/16 (687) 8 5/8 (219) 5 1/16 (128) Front View 3 1 1/2 (38.7) (76) 1 3/8 (34.2) 3 1/4 (82.9) 4 9/16 (115.5) 7 11/16 (195) 2 3/16 (55.5) 3 1/4 (82.5) 2 3/8 (60) 1 1/2 (37.5) 3 1/8 (80) 5/16 (7.5) Bottom View 4 1/8 (104) 10 5/16 (261.5) -122 PG-M25X#E#p116_125.p65 122 02.4.
Glossary Advanced intelligent compression High quality resizing of lower and higher resolution images to fit the projector’s native resolution. Anti-theft If the “Keycode” set in the projector is not correctly entered, the projector will not operate even if signals are entered. Aspect Ratio Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3. There are also wide images with an aspect ratio of 16:9 and 21:9.
Smart Stretch Projects the image fully in a 16:9 screen by enlarging only the surrounding areas while keeping the aspect ratio in the middle part of the image at 4:3. sRGB An international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fixed color area has been decided by the IEC, the color changes according to DLP features, so that the images are displayed in a natural tint based on an original image, when switching to the “sRGB” mode.
Index 2D Progressive .................................................... 60 3D Progressive .................................................... 60 AC socket ............................................................. 26 Adjustment buttons .............................................. 14 Adjustment feet .................................................... 22 All Reset ............................................................ 100 Anti-Theft ...........................................................
SHARP CORPORATION PG-M25X#E#Hyo4.p65 1 02.4.
