Service manual

ManualsBrandsSharp ManualsComputer equipmentMX-PNX1B

SERVICE MANUAL

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with

specified ones for maintaining the safety and performance of the set.

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

SHARP CORPORATION

[1] PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[2] SPECIFICTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

[3] UNPACKING AND INSTALLATION

* For how to unpacking and installation, refer to the installation manual (00ZMX2700/I1E).

[4] EXTERNAL VIEW AND INTERNAL STRUCTURE . . . . . . . . . . . . . 4-1

[5] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

[6] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

[7] MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[8] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

[9] SELF DIAGNOSTICS AND TROUBLE CODES . . . . . . . . . . . . . . . 9-1

[10] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1

 PARTS GUIDE

CONTENTS

MX-FNX1

MX-PNX1A/B/C/D

MODEL

DIGITAL FULL COLOR

MULTIFUNCTIONAL SYSTEM OPTION

FINISHER / PUNCH MODULE

CODE: 00ZMXFNX1/S1E

Summary of content (80 pages)

PAGE 1
SERVICE MANUAL CODE: 00ZMXFNX1/S1E DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM OPTION FINISHER / PUNCH MODULE MODEL MX-FNX1 MX-PNX1A/B/C/D CONTENTS [1] PRODUCT OUTLINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 [2] SPECIFICTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 [3] UNPACKING AND INSTALLATION * For how to unpacking and installation, refer to the installation manual (00ZMX2700/I1E). [4] EXTERNAL VIEW AND INTERNAL STRUCTURE . .
PAGE 2
CONTENTS [1] PRODUCT OUTLINE. . . . . . . . . . . . . . . . . . .1-1 [6] DISASSEMBLY AND ASSEMBLY 1. MX-FNX1 . . . . . . . . . . . . . . . . . . . . . . . . 6-1 [2] SPECIFICTIONS 2. MX-PNX1A/B/C/D . . . . . . . . . . . . . . . . . 6-11 1. MX-FNX1 . . . . . . . . . . . . . . . . . . . . . . . . .2-1 2. MX-PNX1A/B/C/D . . . . . . . . . . . . . . . . . .2-1 [7] MAINTENANCE 1. Maintenance system table . . . . . . . . . . .
PAGE 3
[1] PRODUCT OUTLINE âºíuÇ´ Service Manual This unit is used by installing to the main unit for after-process of copy and FAX output paper. It is provided with the offset function which discharges output paper by shifting one by one. Since it is installed to the center tray section of the main unit, no extra space for installation is required. 1) 3 kinds of auto staple functions: There are 3 kinds of stapling positions. (One position in front, one position backward, 2 positions at the center).
PAGE 4
[2] SPECIFICTIONS âºíuÇ´ Service Manual 1. MX-FNX1 Type Loading method Transport speed Tray type Transport reference Paper exit direction Paper weight Mode type Paper sizes allowed for offset Offset quantity Discharged paper size Sortable size Stack tray max. load capacity Staplable paper weight Staplable paper size Staplable paper quantity (Max.
PAGE 5
Kind of hole punch Kind 2 holes (MX-PNX1A) Hole position A: 80±1mm B: 12±3mm Hole size φ6.5mm A B 3 holes (MX-PNX1B) A A: 108±1mm B: 12±3mm φ8.0mm A: 80±1mm B: 12±3mm φ6.5mm A: 70±1mm B: 12±3mm C: 21±1mm φ6.
PAGE 6
âºíuÇ´ Service Manual [4] EXTERNAL VIEW AND INTERNAL STRUCTURE 1. Identification of each section and functions A. Internal structure 1 5 2 3 4 No. 1 2 3 4 5 6 7 6 7 Name Paper exit roller Bundle exit paper transport roller Paper exit roller Bundle exit paper transport roller Inlet port paper transport roller Inlet port paper transport roller Take-up belt B.
PAGE 7
No.
PAGE 8
(2) MX-PNX1A/B/C/D 3 11 10 9 8 7 6 4 2 1 5 No. 1 Signal FPDD Name Full sensor Type Photo interrupter Function/Operation Detects full of the punch dust container.
PAGE 9
C. Motors, solenoids, and PWB (1) MX-FNX1 3 14 12 9 8 5 7 1 4 6 11 2 10 13 No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Signal FFSM FSM FTLM FFJM FRJM FSWM FAM FRM FPDS FSLS FBRS FINRPS FFAN – Name Staple motor Staple shift motor Tray motor Alignment motor F Alignment motor R Roller upper/lower roller Bundle exit motor Transport motor Paddle one-rotation solenoid Paper surface detection solenoid Belt separation solenoid Flapper solenoid Fan Control PWB Function Drives the stapling mechanism.
PAGE 10
(2) MX-PNX1A/B/C/D 1 5 4 2 3 No. 1 2 3 4 5 Signal FPNM FPSM – – – Name Punch motor Punch horizontal resist motor Punch PWB LED light emitting PWB LED light receiving PWB Function Drives the punch unit up/down. Shifts the punch unit to the center of paper. Controls the punch unit. Detects the paper rear edge and the punch horizontal resist. Detects the paper rear edge and the punch horizontal resist.
PAGE 11
âºíuÇ´ [5] OPERATIONAL DESCRIPTIONS Service Manual 1. Electrical mechanism diagram A.
PAGE 12
B.
PAGE 13
C.
PAGE 14
D.
PAGE 15
2. General This chapter describes operations of the inner finisher. The major operation modes are as follows: • Non-sort mode • Offset mode • Staple mode • Non-sort mode + punch • Offset mode + punch • Staple mode + punch In this chapter, the basic operations of the non-sort mode, the offset mode, and the staple mode are described. 3. Outline of the transport path The outline of the path is shown below. 1 2 3 15 No.
PAGE 16
4. Non-sort mode When the operation mode command is received from the copier, the finisher makes the finisher operation status command the JOB and starts the transport operation. 2) Immediately after the paper rear edge passes the bundle exit roller, the paddle one-rotation solenoid (FPDS) is turned ON to take-up the paper falling onto the tray. 3) When paper is transported by 10mm after the paper rear edge passes the bundle exit roller, the bundle exit motor (FAM) is accelerated to 200mm/sec.
PAGE 17
2) For the second and later sheets of a bundle, the inlet port sensor (FED) turns ON and a certain amount is transported, and then the alignment motor F (FFJM) and the alignment motor R (FRJM) are driven to shift the alignment plate to 15mm outside the paper and to put it under the standby state. 3) After the paper rear edge passes the paper exit roller of the main unit, the transport motor (FRM) is accelerated to 480mm/ sec. 4) In the punch mode, punching is performed as described in "7.
PAGE 18
B. Paper take-up, alignment and staple 1) 8) For the first sheet of a bundle, after turning on the inlet sensor (FED), the roller up/down motor (FSWM) is driven to lower the bundle exit roller. The bundle exit motor (FAM) is driven at the paper exit speed of the main unit to drive the bundle exit roller.
PAGE 19
6) When the paddle rotates one turn, the bundle exit motor (FAM) is stopped. 7) After the paddle rotates one turn, the paper surface detection solenoid (FSLS) is turned ON for 100msec and then OFF. Then it is turned ON after 400msec. At that time, if the paper surface level is lower than the reference level, the tray motor (FTLM) is driven to lift the load tray to the reference level. 8) If there is next paper, the operation is repeated from "A-1).
PAGE 20
[6] DISASSEMBLY AND ASSEMBLY âºíuÇ´ Service Manual 1. MX-FNX1 A. Exterior (1) 1) Inner finisher Loosen the screw, and disconnect the connector from the main unit. (2) 2) Inner cover 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Open the front cover, and remove the punch unit cover. 2 1 (3) Rear cover 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Slide the rail, and remove the rear cover. 2 3) Remove the stopper.
PAGE 21
(5) Reverse guide unit (2) Flapper solenoid 1) Remove the inner finisher from the main unit. Refer to A-(1). 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 2) Disconnect the connector, and remove the flapper solenoid. 3) Remove the reverse guide unit. B.
PAGE 22
(4) Roller up/down sensor (7) Belt separation solenoid 1) Remove the inner finisher from the main unit. Refer to A-(1). 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 2) Remove the inner cover. Refer to A-(2). 3) Remove the bracket, and remove the roller up/down sensor. 3) Remove the reverse guide unit. Refer to A-(5). 4) Remove the parts, and remove the belt separation solenoid.
PAGE 23
(9) 1) Take-up belt, paper exit roller 7) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the reverse guide unit. Refer to A-(5). 4) Remove the parts, and remove the bundle roller up/down lever unit. Remove the parts, and remove the take-up belt and the paper exit roller. 3 1 2 2 1 2 1 5) Remove the parts, and remove the bundle roller unit.
PAGE 24
8) 9) (11) Inlet port paper transport roller Remove the tray unit. 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the tray unit. Refer to B-(10). 4) Remove the bottom plate. Refer to B-(10). 5) Remove the inlet port upper guide, and remove the transport guide. 6) Remove the parts, and remove the inlet port paper transport roller. Remove the harness from the guide, and remove the bottom plate.
PAGE 25
(13) Bundle exit motor 5) 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the tray unit. Refer to B-(10). 4) Remove the bottom plate. Refer to B-(10). 5) Disconnect the connector, and remove the bundle exit motor. Remove the bundle exit paper transport unit. 1 1 1 2 1 3 6) Remove each parts, and remove the sensor lever. 7) Remove the center weight, and remove the process tray unit.
PAGE 26
8) Remove the alignment plate. Remove the screws and the pawl, and remove the process tray. 1 D. Staple section (1) Staple cartridge 1) Open the front cover, and slide the inner finisher. Refer to B(1). 2) Release the lock, and remove the staple cartridge. 2 (2) 9) Staple unit 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Remove the latch cover. Remove the parts and the shaft.
PAGE 27
(3) 1) Alignment plate position sensor 7) Remove the inner finisher from the main unit. Refer to A-(1). 2) Shift the staple unit to the front side. 3) Remove the bracket and remove the position sensor. (5) (4) 1) Disconnect the connector from the PWB, and remove the staple shift motor. Stapler HP sensor 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the inner cover. Refer to A-(2). 3) Put the inner finisher upside down, and remove the stapler HP sensor.
PAGE 28
6) (2) Remove the bracket, and remove the paper surface sensors 1, 2. (3) Tray upper limit sensor, tray intermediate lower limit sensor, tray lower limit sensor 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the tray unit. Refer to B-(10). 3) Remove the harness guide, and remove the tray upper limit sensor, the tray intermediate lower limit sensor, and the tray lower limit sensor. Paper surface detection solenoid 1) Remove the inner finisher from the main unit.
PAGE 29
5) F. Others Remove the gear, and remove the tray motor. (1) 2 Control PWB 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the rear cover. Refer to A-(3). 3) Disconnect the connector, and remove the screw. Remove the PWB support and remove the control PWB. 1 (5) Tray paper empty sensor 1) Remove the inner finisher from the main unit. Refer to A-(1). 2) Remove the left cover and the bottom cover. Refer to A-(4). 3) Remove the tray bottom cover.
PAGE 30
2. MX-PNX1A/B/C/D 5) Remove the punch unit from the main unit. A. Punch unit (MX-PNX1A/B/C/D) (1) Punch unit (MX-PNX1A/B/C/D) 1) Remove the coin screw, and remove the finisher slide stopper. 2) Open the front cover, and slide the inner finisher. (2) LED light receiving PWB 1) Remove the punch unit. Refer to A-(1). 2) Remove the PWB holder, and remove the LED light receiving PWB. 2 1 3) Remove the dust box. (3) Punch horizontal resist motor 1) Remove the punch unit. Refer to A-(1).
PAGE 31
3) Remove the punch horizontal resist motor. 3) Fit the gear hole with the screw position, and remove the screw. Remove the punch motor. 1 2 (4) (6) Punch PWB LED light emitting PWB 1) Remove the punch unit. Refer to A-(1). 1) Remove the punch unit. Refer to A-(1). 2) Remove the guide cover and the harness guide. Refer to A(3). 2) Remove the lower unit. Refer to A-(5). 3) 3) Remove the punch PWB. Remove the roller and the PWB holder. Remove the LED light emitting PWB.
PAGE 32
(8) Punch position sensor 4) 1) Remove the punch unit. Refer to A-(1). 2) Remove the upper unit. Refer to A-(5). 3) Remove the harness guide. Remove the screws and the pawl, and lift up the harness guide. Disconnect the connector, and remove the horizontal shift HP sensor. 3 1 2 4) Remove the punch position sensor. (10) Full sensor (9) 1) Remove the punch unit. Refer to A-(1). 2) Remove the drive bracket, and remove the full sensor. Horizontal shift HP sensor 1) Remove the punch unit.
PAGE 33
[7] MAINTENANCE âºíuÇ´ Service Manual 1. Maintenance system table ✕: Check (Clean, replace, or adjust according to the necessity.) {: Clean S: Replace U: Adjust ✩: Lubricate : Shift position No. Part name When calling 1 2 3 Transport rollers Transport paper guides Gears ✕ ✕ ✕ 4 5 6 7 8 9 Belts Knurling belt Paddle Sensors Discharge brush Stapler unit 10 Punch unit 11 Staple cartridge Follows the main unit cycle.
PAGE 34
[8] ADJUSTMENTS âºíuÇ´ Each adjustment item in the adjustment item list is identified with its own JOB No. The adjustments are basically executed in the sequence from a smaller JOB No. to a larger JOB No. Service Manual 2 Finisher adjustment 1) Enter Simulation 3-10. 2) Select a set item with [↑] [↓] buttons. The highlighted section of the set value is changed and is displayed on the setting area. There is, however, no need to perform all the adjustment items.
PAGE 35
Item D Display STAPLE FRONT Item Staple binding position adjustment (One position, front) Variation 0.155mm E STAPLE BOTH Staple binding position adjustment (2 positions, center) 0.155mm F STAPLE PITCH Staple binding position adjustment (2 positions, pitch) 0.155mm G PUNCH CENTER Punch center adjustment 0.1441mm H PUNCH HOLE Punch hole position adjustment 0.2584mm Change direction Large value: The distance between the staple position and the paper edge becomes longer.
PAGE 36
[9] SELF DIAGNOSTICS AND TROUBLE CODES âºíuÇ´ 1. Trouble code and troubleshooting Service Manual Phenomenon Case 1 A. MX-FNX1 Phenomenon Case 1 Case 2 Case 3 Case 4 Phenomenon Case 1 Case 2 Case 3 Phenomenon Case 1 Case 2 Case 3 Though the main switch of the main unit is turned ON, the inner finisher does not operate. Trouble code: F1-00 Cause Connection failure with the main unit. Check & Check to confirm the connection state of the Remedy connectors.
PAGE 37
Phenomenon Case 1 Case 2 Case 3 Phenomenon Case 1 Case 2 Case 3 A document is discharged to the reverse path in the operation other than reverse operation. Cause Flapper solenoid (FINRPS) connector pin trouble Check & Check the connection state of the connector. Remedy (CN15) Cause Solenoid coil disconnection Check & Perform the conduction test of the coil. If there Remedy is no conduction, replace the coil.
PAGE 38
Case 6 Cause Check & Remedy Phenomenon Case 1 Case 2 Case 3 Case 4 Cause Check & Remedy Cause Check & Remedy Cause Check & Remedy Cause Check & Remedy Control PWB trouble After checking the above 1 to 5, if the phenomenon is not removed though the sensor level is changed and if the motor does not operate in the motor single operation mode, replace the control PWB. The fan (FFAN) does not operate.
PAGE 39
âºíuÇ´ [10] ELECTRICAL SECTION 2) Tray intermediate Service Manuallower limit sensor (FMLLD) The tray intermediate lower limit sensor (FMLLD) employs the photo interrupter in which the light emitting diode and the photo transistor are integrated. 1. Circuit descriptions The lower limit is detected by interruption of lights with the light-shielding plate. A. MX-FNX1 (1) General Signals are inputted to the multiplexer (IC14-14pin) through the noise filter of R12 and C2.
PAGE 40
6) Paper surface sensor 2 (FSLD2) The paper surface sensor 2 (FSLD2) employs the photo interrupter in which the light emitting diode and the photo transistor are integrated. The paper surface is detected by interruption of lights with the lever-type actuator. The logic of the signal inputted to the CPU is L at the front side alignment guide home position. R21 is the current-limiting resistor of the light emitting diode. R25 is the load resistor of the sensor.
PAGE 41
16) Self priming sensor (FSTD) Stapler Alignment plate position sensor (FJPD) The self priming sensor (FSTD) is the built-in sensor of the stapler unit. Self priming is detected by the open-collector output with the circuit in the unit. Stapler home sensor (FSHPD) Signals are inputted to the multi-plexer (IC14-5pin) through the noise filter of RA4.2 and C60. The logic of the signal inputted to the CPU is H in the READY state.
PAGE 42
2) Bundle exit motor (FAM) drive circuit This circuit controls rotation/stop rotating direction and current of the bundle exit motor (FAM), and is composed of the CPU (IC10), the DA converter (IC11), and the constant-current chopper system driver IC (IC8). The motor rotating speed and the rotting direction are controlled with the stepping motor drive excitement pattern signal (T_MOT_A, *A, B, *B) outputted from the CPU (IC10-79, 80, 81, 82pin).
PAGE 43
This circuit controls rotation/stop and the rotating direction of the staple shift motor (FSM) and the motor current, and is composed of the CPU (IC10), the DA converter (IC11), and the constant-current chopper system driver IC (IC4). The motor rotating speed and the rotating direction are controlled with the stepping motor drive excitement pattern signal (ST_MOT_PA, PB, EA, EB) outputted from the CPU (IC1045, 46, 47, 48pin).
PAGE 44
7) Staple motor (FFSM) drive circuit Staple motor (FFSM) This circuit controls rotation/stop and the rotating direction of the staple motor (FFSM), and is composed of the CPU (IC10) and the FET (Q10, 11, 12, 13). The DC motor is controlled with the staple motor (FFSM) drive normal rotation signal, the reverse rotation signal, and the brake signal outputted from the CPU (IC10-5, 8, 9pin).
PAGE 45
d. Flapper solenoid (FINRPS), belt separation solenoid (FBRS), paper surface detection solenoid (FSLS), paddle one-rotation solenoid (FPDS) drive circuit Flapper solenoid (FINRPS) Belt separation solenoid (FBRS) Paper surface detection solenoid (FSLS) Paddle one-rotation solenoid (FPDS) This circuit controls attachment and release of the flapper solenoid (FINRPS), the belt separation solenoid (FBRS), the paper surface detection solenoid (FSLS), and the paddle one-rotation solenoid (FPDS).
PAGE 46
g. Rush current limit circuit Main unit Punch position sensor (FPHPD) Front cover switch (FDSW) Rear position sensor (FPRPD) Horizontal shift HP sensor (FPSHPD) This circuit limits a rush current flowing through the current-regenerating capacitor in the motor drive system to a certain level. It is composed of the posister (PTH2) which limits a current and the FET (Q3) which flows a current in the steady state.
PAGE 47
5) Paper rear edge sensor (FPPEND) and paper horizontal resist sensor (FPPD1 – 6) This circuit is a transmission-type optical sensor circuit using the LED PWB and the photo transistor PWB. Paper is detected when the light path is interrupted by paper passing between the photo transistor PWB and the LED PWB.
PAGE 48
b. Motor drive circuit 1) Punch horizontal resist motor (FPSM) drive circuit Punch horizontal resist motor (FPSM) Not installed This circuit controls the punch horizontal resist motor (FPSM) rotation/stop, the rotating direction, and the motor current, and is composed of the CPU (IC10) on the finisher circuit, the DA converter (IC11), and the constant-current chopper type driver IC (IC2) in the above circuit.
PAGE 49
c. Transmission type sensor circuit 1) LED circuit This circuit is composed of the paper rear edge sensor (FPPEND) on the inner punch circuit and the light emitting (LED) circuit of the paper horizontal resist sensors (FPPD1 – 6) circuit. Turning ON/OFF of LED1 – 7 are controlled by the paper rear edge sensor (FPPEND) and the paper horizontal resist sensors (FPPD1 – 6) circuit.
PAGE 50
2. Block diagram A.
PAGE 51
B.
PAGE 52
3. Actual wiring diagram A.
PAGE 53
4 3 2 1 1/1 Adjustment plate position sensor (FJPD) D (FFAN) Stapler shift motor (FSM) C (FTLM) Alignment motor F (FFJM) Alignment motor R (FRJM) Roller upper/lower motor (FSWM) B Bundle exit motor (FAM) 4 3 A Paddle one-rotation solenoid (FPDS) Paper surface detection solenoid (FSLS) Belt separation solenoid (FBRS) (FINRPS) Transport motor (FRM) 2 MX-FNX1/MX-PNX1 ELECTRICAL SECTION 10 – 15 1
PAGE 54
6 5 4 4 3 3 2 2 (FPNM) 1/1 1 Punch horizontal resist motor (FPSM) 1 C D A 7 5 A 8 6 B Horizontal shift HP sensor (FPSHPD) (FPRPD) (FPHPD) (FPDD) 7 B C D MX-PNX1A/B/C/D 8 B.
PAGE 55
PARTS GUIDE MODEL MX-FNX1 MX-PNX1A MX-PNX1B MX-PNX1C MX-PNX1D このパーツガイドに掲載されている表示価格ランクは消費税抜きです。 CONTENTS 1 2 3 4 5 6 7 8 9 F G H I J K L M 外装部 (EXTERIORS) ■ 索引 (Index) 搬送部 1(TRANSPORT SECTION 1) 搬送部 2(TRANSPORT SECTION 2) 搬送部 3(TRANSPORT SECTION 3) 処理ﾄﾚｲ部 (DISPOSITION TRAY SECTION) ｽﾃｲﾌﾟﾙ部 (STAPLE SCTION) ｽﾀｯｸﾄﾚｲﾕﾆｯﾄ (STACK TRAY UNIT) ｽﾀｯｸﾄﾚｲ駆動部 (STACK TRAY DRIVE SECTION) 前ﾌﾚｰﾑ部 (FRONT FRAME SECTION) 後ﾌﾚｰﾑ部 1(REAR FRAME SECTION 1) 後ﾌﾚｰﾑ部 2(REAR FRAME SECTION 2) ﾌﾚｰﾑ部 (FRAME SECTION) 梱包＆付属品 (PACKING &
PAGE 56
補修部品のランク付市場における補修部品の在庫管理が、適正に運営出来る手助けとなることを、目的とします。 Aランク : メンテナンスパーツ、メンテナンスパーツには入っていないがメンテナンスパーツに近い消耗パーツ。 Bランク : 性能・機能パーツ（センサー、クラッチ等の電気パーツ）、消耗パーツ。 Eランク : 基板含むユニットパーツ。 Dランク : 整備パーツ（外装、パッキング、同梱パーツ）。 Cランク : 上記ランク以外のパーツ（基板の子部品を除いたもの）。 DEFINITION Rank Rank Rank Rank Rank A B E D C : : : : : Maintenance parts, and consumable parts which are not included in but closely related to maintenance parts Performance/function parts (sensors, clutches, and other electrical parts), consumable parts Unit parts includi
PAGE 57
2 搬送部 1(TRANSPORT SECTION 1) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 48 PRICE RANK Ex. Ja.
PAGE 58
3 搬送部 2(TRANSPORT SECTION 2) NO.
PAGE 59
4 搬送部 3(TRANSPORT SECTION 3) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 PRICE RANK Ex. Ja.
PAGE 60
5 処理ﾄﾚｲ部 (DISPOSITION TRAY SECTION) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 PRICE RANK Ex. Ja.
PAGE 61
6 ｽﾃｲﾌﾟﾙ部 (STAPLE SCTION) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 PARTS CODE 0CWNSBLT00342 0CW4141P225// 0CW4141K011// 0CW030060FWWS 0CW4141K020// 0CW4141P138// 0CW4141P034// 0CW4099P769// 0CW4141P319// 0CW030060FWTP 0CW040080FWWS 0CW4141P520// 0CW4141P410// 0CW4141P405// 0CW4141P137// 0CW4141P424// 0CWNSCLP00003 0CW4141P427// 0CWNSCLP00005 0CW4141P425// 0CW4141P144// 0CWE314000784 0CWE450001128 0CWE450001174 0CW4141P325// 0CW4141K219// 0CWE450000842 PRICE RANK Ex. Ja.
PAGE 62
7 ｽﾀｯｸﾄﾚｲﾕﾆｯﾄ (STACK TRAY UNIT) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 PARTS CODE 0CW4141P024// 0CW4141P023// 0CW4141P022// 0CW4141P037// 0CW4141P090// 0CWE314000784 0CW4141P029// 0CWNSSCR00023 0CW4141P031// 0CWNSCLP00003 0CW4141P030// 0CW4141P028// 0CW030060FWWS 0CW4141P033// 0CW030060FWTP 0CW4141P121// 0CW4141P109// 0CWNSSCR00056 0CW4141K054// 0CW4141K079// 0CW4141P032// 0CW4141P019// 0CW4141K212// 0CW4141P331// PRICE RANK Ex. Ja.
PAGE 63
8 ｽﾀｯｸﾄﾚｲ駆動部 (STACK TRAY DRIVE SECTION) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 PRICE RANK Ex. Ja.
PAGE 64
9 前ﾌﾚｰﾑ部 (FRONT FRAME SECTION) NO.
PAGE 65
F 後ﾌﾚｰﾑ部 1(REAR FRAME SECTION 1) NO.
PAGE 66
G 後ﾌﾚｰﾑ部 2(REAR FRAME SECTION 2) NO.
PAGE 67
H ﾌﾚｰﾑ部 (FRAME SECTION) NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 PRICE RANK Ex. Ja.
PAGE 68
I 梱包＆付属品 (PACKING MATERIAL & ACCESSORIES) NO. PARTS CODE 0CW040080FWBP 0CW4141P047// 0CW4115P301// 0CWNSCLP00011 0CW616371//// 0CW4141P050// 0CW2111P021// 0CW4141P041// 0CW1035P032// 0CW4141K003// 0CW2216P524// 0CW4134P420// 0CW4141P362// 0CW4141P361// 0CW4141P607// 0CW2158P380// 0CW4141P611// 0CW2229P412// 0CW4141K080// 0CW4141P601// 23 0CW4141P609// 24 0CW4141P610// 1 2 3 4 5 6 7 8 9 10 12 13 14 15 16 17 19 20 21 PRICE RANK Ex. Ja.
PAGE 69
I 梱包＆付属品 (PACKING MATERIAL & ACCESSORIES) 1 5 6 12 2 19 12 15 7 3 16 13 14 4 7 9 8 21 20 12 7 17 10 10 24 10 23 FCP08963 J ﾊﾟﾝﾁﾕﾆｯﾄ 1(PUNCH UNIT 1)[MX-PNX1] 3 2 2 16 14 5 3 2 54 42 46 9 7 54 50 6 3 1 45 4 2 2 38 44 7 5 40 39 51 44 2 10 17 52 12 18 19 20 15 2 36 22 11 37 35 55 43 34 2 2 2 13 30 2 25 25 2 33 16 41 53 26 5 29 28 32 FCP08964 2 27 5 5 – 14 – 2 23 2 24 31 21
PAGE 70
K ﾊﾟﾝﾁﾕﾆｯﾄ 2(PUNCH UNIT 2)[MX-PNX1] NO. PARTS CODE 1 0CW1035P027// 2 0CWNSSCR00023 0CW1035P319// 3 0CW1035P320// 4 0CWIR4016P167 0CW1035K024// 5 0CW1035K034// 6 0CW1020P786// 7 0CW1020P823// 0CW1035P039// 8 0CW1035P040// 0CW1035P023// 9 0CW1035P013// 0CW1035P025// 0CW1035P210// 11 0CW1035P209// PRICE RANK Ex. Ja.
PAGE 71
K ﾊﾟﾝﾁﾕﾆｯﾄ 2(PUNCH UNIT 2)[MX-PNX1] 2 1 3 4 5 2 6 7 2 2 8 2 7 9 6 17 34 11 18 6 11 7 2 35 11 2 20 13 12 32 30 2 16 16 7 2 22 33 14 12 21 25 27 24 22 22 23 MX-PNX1C MX-PNX1D 33 7 31 24 26 15 2 7 2 FCP08965 28 36 29 L ﾊﾟﾝﾁﾕﾆｯﾄ 3(PUNCH UNIT 3)[MX-PNX1] 3 21 2 8 1 5 22 6 7 4 5 22 19 17 16 20 19 9 8 15 21 18 19 9 19 9 10 9 13 19 11 9 11 14 FCP08966 12 – 16 –
PAGE 72
M 梱包＆付属品 (PACKING MATERIAL & ACCESSORIES)[MX-PNX1] NO. PARTS CODE 0CW4134P420// 0CW1035P338// 0CW1035P337// 0CW2111P021// 0CW1035P335// 0CW1020P832// 0CW1035P329// 0CW1035P332// 9 0CW1035P331// 0CW1035P334// 0CW1035P333// 1 2 3 4 6 7 PRICE RANK Ex. Ja.
PAGE 73
■ 索引 (Index) PARTS CODE [0] 0CW020100SCH/ " 0CW020120SCH/ " " " " 0CW020140SCH/ 0CW023100FNWS 0CW030040FWBI " 0CW030050FWWS " " " 0CW030060FWSW " " " " " " 0CW030060FWTP " " " " " " " " " 0CW030060FWWS " " " " " " " " 0CW040060FWBI " 0CW040080FWBP 0CW040080FWWS 0CW1020P786// 0CW1020P822// 0CW1020P823// 0CW1020P832// 0CW1035K012// 0CW1035K013// 0CW1035K024// 0CW1035K025// 0CW1035K028// 0CW1035K034// 0CW1035K035// 0CW1035K041// 0CW1035K044// 0CW1035K046// 0CW1035K203// 0CW1035K204// 0CW1035K205// 0CW1035K21
PAGE 74
PARTS CODE 0CW2216P524// 0CW2229P412// 0CW2268P076// " " 0CW2294P420// 0CW4051P361// 0CW4076P069// 0CW4099P769// " " 0CW4102P308// 0CW4102P386// 0CW4115P301// 0CW4123P079// 0CW4134P420// " 0CW4141K003// 0CW4141K007// " 0CW4141K009// 0CW4141K011// " " 0CW4141K020// 0CW4141K023// 0CW4141K025// 0CW4141K040// 0CW4141K051// 0CW4141K052// 0CW4141K054// 0CW4141K059// 0CW4141K062// 0CW4141K078// 0CW4141K079// 0CW4141K080// 0CW4141K201// 0CW4141K210// 0CW4141K211// " 0CW4141K212// " 0CW4141K213// " 0CW4141K214// " 0
PAGE 75
PARTS CODE 0CW4141P121// 0CW4141P122// 0CW4141P123// 0CW4141P132// 0CW4141P135// 0CW4141P136// 0CW4141P137// 0CW4141P138// 0CW4141P144// 0CW4141P145// 0CW4141P146// 0CW4141P147// 0CW4141P149// 0CW4141P150// 0CW4141P151// 0CW4141P152// 0CW4141P154// 0CW4141P155// 0CW4141P156// 0CW4141P157// 0CW4141P202// 0CW4141P203// 0CW4141P204// 0CW4141P208// 0CW4141P211// 0CW4141P225// 0CW4141P229// 0CW4141P300// 0CW4141P301// 0CW4141P303// 0CW4141P304// 0CW4141P306// 0CW4141P307// 0CW4141P308// " 0CW4141P309// 0CW4141P3
PAGE 76
PARTS CODE 0CWER030SKP// 0CWER040SKP// 0CWER050SKP// " " 0CWER070SKP// " 0CWHW060FNSN/ " 0CWIR4016P167 " " 0CWNSBLT00059 0CWNSBLT00086 0CWNSBLT00211 0CWNSBLT00309 0CWNSBLT00342 0CWNSBLT00343 0CWNSBSH00002 0CWNSCLP00003 " " " 0CWNSCLP00005 " " " " " " 0CWNSCLP00008 " " " " 0CWNSCLP00011 0CWNSMTL00007 " " 0CWNSMTL00009 " " " 0CWNSSCR00016 " " 0CWNSSCR00023 " " " " " " " 0CWNSSCR00056 0CWNSSCR00214 0CWSP03010FPA NO.
PAGE 77
Memo
PAGE 78
LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: Lead-Free 5mm Solder composition code (Refer to the table at the right.
PAGE 79
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
PAGE 80
COPYRIGHT © 2005 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher. Trademark acknowledgements Microsoft® Windows® operating system is a trademark or copyright of Microsoft Corporation in the U.S.A. and other countries.