MD-MT877/MD-MT877C SERVICE MANUAL No. S3118MDMT877/ PORTABLE MINIDISC RECORDER MD-MT877(S) MODEL MD-MT877C(S) • In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS Page SPECIFICATIONS ................................................................................................................................................................. 2 NAMES OF PARTS .................................................
MD-MT877/MD-MT877C FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL. SPECIFICATIONS Power source DC 1.2V: DC 5V: DC 1.5V: DC 1.
MD-MT877/MD-MT877C NAMES OF PARTS Main unit 1. Record/Track Mark Button 2. Mode Button 3. Volume/Cursor/Fast Forward/Fast Reverse/ Recording Level/Name Select Button 4. Stop/Power Off/Hold Button 5. Open Lever 6. Display/Character Select Button 7. Edit/Auto Mark/Time Mark Button 8. Play/Pause Button 9. Enter/Fast Play/Synchro Button 10. Bass/Delete Button 11. Rechargeable Battery Cover 12. Handstrap Holder 13. Optical/Line Input Jack 14. Microphone Input Jack 15.
MD-MT877/MD-MT877C Remote control unit 1. 2. 3. 4. 5. 6. 7. 8. 9. Remote control display panel 1. 02. 03. 04. 05. 06. 07. 08. 09. 10.
MD-MT877/MD-MT877C OPERATION MANUAL Using with the Rechargeable Battery Charging Do not force the battery cover open too far. When the rechargeable battery is used for the first time or when you want to use it after a long period of disuse, be sure to charge it fully. 1 2 3 AC 120V 60Hz Insert the rechargeable battery. Move the Charge/Operation switch to charge mode. Place the portable MD into the battery charger and connect the AC adaptor.
MD-MT877/MD-MT877C Error Messages ERROR MESSAGES BATT EMPTY MEANING REMEDY ● The battery is run down. ● Nothing is recorded. ● Charge the rechargeable battery or replace the alkaline battery (or use the AC adaptor for power). ● Replace the disc with a recorded disc. ● You tried to record from a copy prohibited MiniDisc. ● A track cannot be edited. ● Record using the analog cable. (MD-MT877(S)) ● Record using the analogue cable. (MD-MT877C(S)) ● Change the stop position of the track and then edit it.
MD-MT877/MD-MT877C MiniDisc System Limitations The unit may have the following symptoms while recording or editing. The unit is not out of order. SYMPTOM LIMITATIONS “DISC FULL” or “TOC FULL” appears More than 255 tracks (maximum) cannot be recorded regardless of the reeven though the MiniDisc still has re- cording time. cording time left. If the MiniDisc is recorded or edited repeatedly or if it has scratches (recording skips scratched parts), you may not be able to record the maximum tracks above.
MD-MT877/MD-MT877C 1 2 Insert a MiniDisc Inserte un minidisco 2 Connect the AC adaptor Conecte el adaptador de CA Insert according to the direction of the arrow. 4 Insértelo de acuerdo con la dirección de la flecha. AC 120V, 60 Hz 120V CA, 60Hz 3 1 To an AC outlet A un tomacorriente de CA RELEASE LOCK 1 Slide the OPEN lever to re- 3 Insert a MiniDisc as shown. lease the compartment door. Deslice la palanca OPEN para abrir la puerta del compartimiento.
MD-MT877/MD-MT877C Recording Grabación Check that the unit is connected to the stereo system. Compruebe que el aparato esté conectado al sistema estéreo. 4 Press the PAUSE button on the stereo system to enter the playback pause mode at the point you wish to start recording. Pulse el botón PAUSE del sistema estéreo para entrar en el modo de pausa de reproducción en el punto en el que desee iniciar la grabación. 5 Press the MODE button repeatedly to select the recording mode.
MD-MT877/MD-MT877C DISASSEMBLY Cares before disassembling When assembling the machine after disassembling or repair, observe the following requirements so as to ensure safety and performance. 1. Remove the batteries from the machine, and take out the mini-disc. 2. When assembling after repair, be sure to position the wires in the same location. Use the specified screws to fix the cabinet and the mechanism unit.
MD-MT877/MD-MT877C REMOVING AND REINSTALLING THE MAIN PARTS Remove the mechanism according to the disassembling methods 1 to 4. (See Page 10.) How to remove the spindle motor (See Fig. 11-1.) 1. Remove the solder joints (A1) x 4 of flexible PWB. 2. Remove the screws (A2) x 3 pcs., and remove the spindle motor. (A2) x 3 ø 1.4 x 3 mm Spindle Motor How to remove the lift motor (See Fig. 11-2.) Solder joints (A1) x 4 1. Remove the solder joints (B1) x 2 of lift motor lead wire. 2.
MD-MT877/MD-MT877C ADJUSTMENT Test disc MD adjustment needs two types of disc, namely recording disc (low reflection disc) and playback-only disc (high reflection disc). Type Test disc Parts No. 1 High reflection disc MMD-110 88GMMD-110 (TEAC Test MD) 2 Low reflection disc MMD-213A 88GMMD-213A (TEAC Test MD) 3 Low reflection disc Recording minidisc disc UDSKM0001AFZZ Note: Use the low reflection disc on which music has been recorded. Entering the TEST mode 1.
MD-MT877/MD-MT877C Operation in each TEST mode 1. AUTO1 Mode 5. TEST-PLAY Mode • When the STOP button is pressed while the AUTO1 menu appears or during automatic adjustment, the mode changes to the TEST mode stop state. At this time the adjustment value is not output. • Be sure to adjust, using the specified disc MMD-213A. • Adjustment NG; Adjustment item out of range, focus ON failure, and adjustment error • When the PLAY button is pressed while ADJ. OK is displayed, AUTO2 is executed.
MD-MT877/MD-MT877C 6. TEST-REC Mode 7. NORMAL Mode • When the STOP button is pressed while the TEST-REC menu appears, or in the TEST-REC mode or continuous record mode, the mode changes to the TEST mode stop state. • Whenever the DISP button is pressed in the TEST-REC menu, the target address changes as follows. • When the STOP button is pressed while the NORMAL menu appears, the mode changes to the TEST mode stop state.
MD-MT877/MD-MT877C EEPROM (IC402) writing procedure 1. Procedure to replace EEPROM and write initial value of microcomputer in EEPROM (1) Replace EEPROM. (2) Refer to the latest EEPROM data list. (3) Start the test mode. (Refer to page 12 "Entering the TEST mode".) (4) Version display (At the time of settlement of the test mode by the button operation.) [Ver. ] (7) Press the "BASS" button, and press 1 time the "FAST REVERSE" button.
MD-MT877/MD-MT877C EEPROM DATA LIST (EEPROM version C) Fucus setting Spindle setting Item display FG1 _ Item display Set values 44H SPG _ Set values 30H FG2 _ FF0 _ 70H 10H SPi _ SPm _ 9AH 62H FF1 _ FF2 _ 70H E8H SPo _ PGM _ 4FH E0H Ff0 Ff1 _ _ 10H 48H SP1 _ SP2 _ 10H 60H Ff2 _ FZH _ EAH EDH SP3 _ SP4 _ F2H F2H FLn _ FLp _ 09H 06H SP5 _ Sp2 _ 10H 60H DJG _ FSS _ 0FH 28H Sp5 _ SD1 _ 10H 7FH FTS _ FSB _ 18H 40H SD2 _ SPK _ 7FH EBH FTB _ FGM _ 38H 66H MPG _ SPL _ 28H 60H
MD-MT877/MD-MT877C Control setting BASS setting Item display B1A _ B1B _ Item display Set values 3FH 00H B1C _ B2A _ 00H 1FH B2B _ B2C _ 00H 00H B3A _ B3B _ E2H 00H B3C _ 00H CT0 _ ADJ.
MD-MT877/MD-MT877C Do the following when replacing the mechanism, the pickup, the EEPROM (IC402), the LSI(IC201) or the main PWB unit. Enter the test mode, move the pickup to the most internal periphery and execute AUTO1. (Use the disc of MMD-213A.) AUTO1 PLAY (During the spare style automatic adjustment) AT1 Normality completion ADJ.OK PLAY (During the adjustment that ATT is automatic) AT2 Normality completion ADJ.
MD-MT877/MD-MT877C Change of Tset Mode Menus BASS TEST : Test mode stop SKIP DOWN SKIP UP Slide external periphery move Slide internal periphery move SKIP DOWN AUTO1 : Pre-automatic adjustment menu SKIP UP SKIP DOWN AUTO2 SKIP UP T SKIP DOWN PLAY SKIP UP T : ATT auto adjustment menu : Continuous playback menu SKIP DOWN REC SKIP UP : Continuous record menu SKIP DOWN MANU1 SKIP UP : Pre-manual adjustment menu SKIP DOWN MANU2 SKIP UP : ATT manual adjustment menu SKIP DOWN RSLT1 SKIP UP
MD-MT877/MD-MT877C Servo ATT Auto Adjustment AUTO2 : ATT auto adjustment menu PLAY AT2 : During ATT auto adjustment Adjustment error Normal end ADJ. NG : ATT adjustment error (adjustment value output) : ATT adjustment error (adjustment value output) ADJ. OK PLAY SQ#### AP#### : Continuous playback (high reflection) : Continuous playback (low reflection) * When the [STOP] button is pressed in specific menu, the "TEST MODE STOP" state is set.
MD-MT877/MD-MT877C * In the continuous playback state the number of jump lines changes as follows shown the [BASS] button is pressed. 1 (initial value) 10 1TR BASS BASS 10TR 100stp 100s tep BASS * When the [FAST FORWARD] button is pressed in the continued playback mode, jump of specified number of lines occurs in the external periphery direction. If the key is held down jump occurs continuously (100 ms cycle).
MD-MT877/MD-MT877C Servo Pre-Manual Adjustment MANU1 : Pre-Manual Adjustment menu PLAY TMP SKIP UP : Temperature code indication $ $ : Temperature code $ $ SKIP DOWN : A signal offset (AINO) measurement : Measurement value Ah SKIP UP SKIP DOWN : B signal offset (BINO) measurement : Measurement value Bh SKIP UP SKIP DOWN : E signal offset (EINO) measurement : Measurement value Eh SKIP UP SKIP DOWN : F signal offset (FINO) measurement : Measurement value Fh SKIP UP LON SKIP UP SKIP DOWN : Las
MD-MT877/MD-MT877C • ABMAXO measurement value Sa Sb : A-ATT (focus) tentative setting : B-ATT (focus) tentative setting DISP DISP : ABMAXO measurement value indication "1" Mark lighting AB • LPFABO measurement value : A-ATT (focus) tentative setting : B-ATT (focus) tentative setting SA SB DISP DISP : LPFABO measurement value indication "1" Mark lighting ab • LPFEFO measurement value : Pit section adjustment COUT level setting : Group section adjustment COUT level setting PCH GCH DISP DISP : LP
MD-MT877/MD-MT877C g j HB Lb LB : High-reflection pit section B-ATT (focus) setting : Low-reflection pit section B-ATT (focus) setting : Low-reflection groove section B-ATT (focus) setting : ATT setting PLAY P-MODE : Continuous playback (pit section) : Continuous playback (groove section) # # # # : Address SQ#### AP#### * If the [BASS] button is pressed in the laser ON state (with no disc or the lid open), laser power changes as follows.
MD-MT877/MD-MT877C Servo Pre-adjustment Value Check RSLT1 : Pre-adjustment Value Check menu PLAY AH SKIP UP : A signal offset measurement value (setting) SKIP DOWN BH SKIP UP : B signal offset measurement value (setting) SKIP DOWN EH SKIP UP : E signal offset measurement value (setting) SKIP DOWN FH SKIP UP : F signal offset measurement value (setting) SKIP DOWN TH SKIP UP : TCRS signal offset measurement value SKIP DOWN ef SKIP UP : EF signal measurement value SKIP DOWN TC SKIP UP : TCRS si
MD-MT877/MD-MT877C Error History Display • Error history clear E DATA : Error history indication menu After one second DISP CLEAR : Error history clear • Error history indication E DATA : Error history indication menu PLAY : Error history 0 indication $ $ : Error code E0$$ SKIP UP SKIP DOWN : Error history 1 indication $ $ : Error code E1$$ SKIP UP SKIP DOWN : Error history 2 indication $ $ : Error code E2$$ SKIP UP SKIP DOWN : Error history 3 indication $ $ : Error code E3$$ SKIP UP S
MD-MT877/MD-MT877C Test Mode Normal Playback NORMAL : Test mode normal playback menu PLAY : Normal playback mode @@@@@@: Mode and address indication @@@@@@ * When the [STOP] button is pressed in specific menu, the "TEST MODE STOP" state is set.
MD-MT877/MD-MT877C NOTES ON SCHEMATIC DIAGRAM • Resistor: To differentiate the units of resistors, such symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is ohm-type resistor. Besides, the one with “Fusible” is a fuse type. • Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means pico-farad and the unit of the capacitor without such a symbol is microfarad.
– 29 – Figure 29 BLOCK DIAGRAM M902 SLED MOTOR 39,41,43 27,31, 40,45 VM IC601 MOTOR DRIVE BD6640KV PLAYBACK SIGNAL RECORD SIGNAL 7,10,12 55,60 +2.5V 29,40 IC402 EEPROM 58X2404T IC404 GATE IC N7SZ86P5 IC431 RESET S-80820LNP 1-3,17,27,52,64 2 1 8 66 2,5 76 59 1-11,36,38, 73,74,93 68 2,5,6,7 KEY UNIT SWA01-13 1-3 31-33 40,47, 48,81, 91,92 96-99 4,7 49,72 4 SW901 DISC PROTECT 12,53,54,62 SW401 EJECT 2 +B 14,51,62 +1.5V 74 73 2.
MD-MT877/MD-MT877C +B TP202 TP139 L103 LDVAR LDON OPICGA TP113 TP114 TP115 TP116 TP117 TP118 TP119 TP120 TP121 TP105 TP106 TP107 TP108 TP109 TP110 TP111 TP101 TP102 TP103 C 15 C121 220P 9 TP487 RAA11 RAD0 RAD1 RAWEX RARASX RAA9 RAD3 RAD2 RACASX DGND RAOEX RAA8 RAA7 RAA6 SLDRR RAA5 SPDRF RAA4 SPDRR VDD2 RAA3 RAA10 RAA2 RAA0 RAA1 ACRCER PLCK EFMO X700KO TCRS 48 49 50 51 52 IC201 LR378161 ENDEC/SERVO /ATRAC 23 24 25 26 27 1 EFMMON 2 AVCC 98 SYWRX 99 SYRDX 100 SYRS 1 2 3 4 5 6 7 8 9 10 11 12 1
MD-MT877/MD-MT877C LCD ASS'Y 10 11 12 13 14 TLGU1008 470 C509 1 470 C510 1 TP410 TP411 DISPLAY SWA06 VOLUME– SWA07 SWA08 SWA09 VOLUME+ STOP MODE SWA10 FAST REVERSE SWA11 FAST FORWARD SWA12 ENTER AGND LIHP LOUT 3 0V IC404 N7SZ86P5 GATE IC C703 0.01 VEE DGND AMP&GAIN SEL. LHPVEE +B 3.3/10 C722 R+ R765 15 R766 C766 0.22 15 C753 1 D494 15AZ7.5Y N.C. RDATA L457 L458 D493 015Z5.1Y ELON 2.73V 2.
MD-MT877/MD-MT877C MAIN PWB-A (TOP VIEW) 20 60 15 IC401 R762 10 C724 L713 R729 4 L712 6 R492 13 CK113 R723 R724 L714 C725 1 L704 C912 R412 Q711 1 2 C353 8 R206 IC353 R292 R361 L702 2 R351 C361 D351 R291 C351 C731 C291 L703 C713 3 1 5 R713 J701 OPTICAL/LINE IN : Through-hole where the top, bottom and +B patterns are connected. : Through-hole where the top, bottom and hround patterns are connected. : Through-hole where the top and bottom patterns are connected.
MD-MT877/MD-MT877C MAIN PWB-A (BOTTOM VIEW) GND TERMINAL,- CONTROL TERMINAL EXTENSION BATTERY TERMINAL,+ EXTENSION TERMINAL,+ BATTERY TERMINAL,+ TP206 C202 TP804 TP805 R282 L202 TP200 R281 R151 Q103 TP841 C132 C112 C110 R112 CK225 CK222 CK205 R103 L821 TP660 TP659 C846 D772 C775 TP352 C858 TP702 TP707 R710 L602 L601 L603 L604 C776 C822 IC501 10 TP202 C869 C771 TP500 C506 C505 C823 TP771 TP351 IC851 7 8 TP412 9 C502 D851 D S C764 C510 TP708 TP772 G 15 16 9
MD-MT877/MD-MT877C LCD/KEY PWB-B(TOP VIEW) 1 A CN451 TO MAIN PWB P32 2-F 14 FLEXIBLE PWB B C D LCD/KEY PWB-B(BOTTOM VIEW) E LEDA04 P35 7-H LCD ASS'Y LEDA03 F LEDA02 RA12 RA14 RA13 CA02 7 RA15 CNA01 QA01 SWA08 STOP SWA07 VOLUME+ RA08 SWA05 DISPLAY RA04 RA03 RA02 1 SWA02 PLAY SWA06 VOLUME– SWA01 RECORD SWA09 MODE RA06 RA01 RA07 SWA12 ENTER SWA11 FAST FORWARD G RA05 CA01 RA16 SWA13 OPEN/ CLOSE SWA03 BASS SWA04 EDIT SWA10 FAST REVERSE H : Through-hole where the top and bottom pat
MD-MT877/MD-MT877C M902 SLED MOTOR CN601 TO MAIN PWB P32 2-D MAGNETIC HEAD(3) M903 LIFT MOTOR MECHANISM FLEXIBLE PWB(5) M901 SPINDLE MOTOR LCD ASS'Y(217) OPTICAL PICKUP(4) CN101 TO MAIN PWB P32 2-B CNA01 TO LCD/KEY PWB P34 4-F 7 8 9 10 Figure 35 WIRING SIDE OF P.W.
MD-MT877/MD-MT877C VOLTAGE IC101 PIN NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 VOLTAGE 0.26 V 0.26 V 0.26 V 0.26 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 1.25 V 0.26 V 1.48 V 0V 0V 2.49 V 2.49 V 1.78 V 0V 1.25 V 1.25 V 0.26 V 1.25 V 1.25 V 1.3 V 1.28 V 0.7 V 2.49 V 1.51 V 0V 1.25 V 0.28 V 0.28 V 1.25 V 0.28 V 0.
MD-MT877/MD-MT877C WAVEFORMS OF MD CIRCUIT T Stopped CH1=1mV DC 10:1 1 CH2=500mV DC 10:1 CH3=5V DC 10:1 TP208 (FEMON) 5 IC501(9) (SDTi) 6 IC501(12) (SCLK) TP120 (F+) CK206 (CIN) 4 CK204 (FOK) 7 8 T CH2=2V DC 10:1 CH3=500mV DC 10:1 1994 / 12 / 16 01:03:40 2ms/div (2ms/div) ENV TP201 (EFMMON) 1 TP210 10 (TEMON) IC501(10) (LRCK) T 2 11 TP209 (TOTMON) IC501(11) (MCLK) 4 CH1 CH2 CH3 CH4 =Offset= : 0.00V : 0.000V : 0.00V : 0.
MD-MT877/MD-MT877C TROUBLESHOOTING Use the test mode which indicates trouble causes before repairing the unit. This mode records maximum 2 past error causes as codes. Refer them for repairing. Preparations If dusts and foreign materials are accumulated on the pickup lens, playback sounds can be skipped or the TOC (Table of Contains) can't be displayed. Clean the object lens and check the playback. When lens are dirty, do the following.
MD-MT877/MD-MT877C • Abnormal display. Is waveform output from CN451 pins 3 to 5 ? Are the pin 2 (VCC) and pin 12, 13 (GND) normal ? Is waveform output from IC401 pins 31 to 33 ? No No Yes Yes Check between IC401 and CN451. Check the periphery of IC401. Check for pattern breakage of flexible PWB, check for defects of display microcomputer (replace the display unit). • Audio playback clrcult. In the normal playback mode, LCD play time display functions, but no audio is heard.
MD-MT877/MD-MT877C • Recording/playback operation. Insert a low reflection disc, and ascertain audio output by normal playback, and then set TEST REC mode. Change MSL from 00H to 80H by the control setting of EEPROM. After completing the operation, return in to 00H. Does the head move down, failing to start record even when the continuous record mode is set after address ? No Yes Does the RF waveform appear at TP201 when recording/ Playback is performed.
MD-MT877/MD-MT877C FUNCTION TABLE OF IC IC401 RH-iX0419AWZZ :System Microcomputer (IX0419AW) (1/2) Pin No. Port Name Terminal Name Input/Output Function 1 PE5 SYRS Output System LSI register selection output. 2 PE6 _SYRD Output System LSI read enable output. 3 PE7 _SYWR Output System LSI write enable output. 4-11 PD0-PD7 SYD0-SYD7 12 CVCC CVCC Input/Output Input 13 PC0 PCLAT Output 14 Vss VSS 15 PC1 _MCPGI Input Microphone plug insertion detection input.
MD-MT877/MD-MT877C IC401 RH-iX0419AWZZ :System Microcomputer (IX0419AW) (2/2) Pin No. Port Name Terminal Name Input/Output — Function 58 OSC1 OSC1 59 RES _RESET Input Microcomputer hard reset input. 60 NMI DCIN Input DC IN edge detection. 61 STBY _STBY Input Microcomputer standby input (not used). 62 VCC VCC Input 63 XTAL XTAL — Crystal connection terminal. 64 Vss VSS — Ground potential. 65 EXTAL EXTAL — Crystal connection terminal.
MD-MT877/MD-MT877C IC201 VHiLR378161-1 :Endec/Servo/Atrac (LR378161) System LSI expansion output port Pin No. Port Name Terminal Name Input/Output Function Remarks 56* EXPORT4 Undecided justice Output Not used Not used 57 EXPORT5 LDCNT1 Output Recording head raising-lowering control output 0. See the separate table *3. 58 EXPORT6 LDCNT2 Output Recording head raising-lowering control output 1. See the separate table *3. 59 EXPORT7 EMPH1 Output Audio emphasis control output 1.
MD-MT877/MD-MT877C —MEMO— – 44 –
MD-MT877/MD-MT877C PARTS GUIDE PORTABLE MINIDISC RECORDER MD-MT877(S) MODEL MD-MT877C(S) “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF. No. 3. PART NO. 4. DESCRIPTION For U.S.A. only Contact your nearest SHARP Parts Distributor to order.
MD-MT877/MD-MT877C NO.
MD-MT877/MD-MT877C NO.
MD-MT877/MD-MT877C NO.
MD-MT877/MD-MT877C NO. PRICE RANK PARTS CODE SPAKZ0630AWZZ SPAKZ0692AWZZ SSAKA0009AWZZ J J J DESCRIPTION NO.
MD-MT877/MD-MT877C 501x2 501 506x3 16 A 504x2 M901 502 B 3 10 M902 505 12 4 C 503 507 2 M903 15 17 1 D 14 E 6 11 508 13 F G 9 7 5 H 1 2 3 4 Figure 5 MD MECHANISM EXPLODED VIEW –5– 5 6
MD-MT877/MD-MT877C MD MECHANISM 205 A 603x2 B 201 OP EN 203 218 236 603x2 235 237 C 219 220 207 209 221 210 204 EN OP 208 D 212 241 212 223x2 601 212x3 224x2 MAIN PWB 213 601 225x4 226 E 214 242 216 215 232 233 602 227 234 F 228 217 229 230 238 G 603x2 239x3 603 LCD PWB 202 240 236 231 603 601 604x4 H 603 603 1 2 3 4 Figure 6 CABINET EXPLODED VIEW –6– 5 6
MD-MT877/MD-MT877C A 22-1 B 22-7 22-6 22-3 C 22-7 22-4 22 D 22-8 22-5x2 E 22-2 F 22-5x2 G 22-9 H 1 2 3 4 Figure 7 BATTERY CHARGER EXPLODED VIEW –7– 5 6
MD-MT877/MD-MT877C PACKING OF THE SET (MD-MT877(S) FOR U.S.A. ONLY) Setting position of switches and knobs Remote Control HOLD CANCEL Operation Manual Connecting Cord, Optical Type Quick Guide Carrying Case Sheet, Bubble SPAKZ0692AWZZ Battery Label, Caution Battery Case Remote Control AC Adaptor Packing Add.
MD-MT877/MD-MT877C —MEMO— –9–
MD-MT877/MD-MT877C —MEMO— – 10 –
MD-MT877/MD-MT877C COPYRIGHT © 2001 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.