Installation guide

ManualsBrandsSharp ManualsMicrowaveOfficial Sharp electric range with microwave drawer

30" Slide-in Range

iNSTALLATiONANDSERVICEMUSTDEPERFORMEDBYA QUALiFiEDiNSTALLER.

iMPORTANT: SAVE THiS iNSTALLATiON MANUAL FOR LOCALELECTRICAL

iNSPECTOR'S USE,

READANDSAVETHESEiNSTRUCTiONSFORFUTUREREFERENCE,

For SAFETY CONSiDERATiONS do not install a range in any combustible cabinetry which is not in

accord with the stated clearances and dimensions on page 2. See Figures 1 and 2.

RANGEMEASUREMENTS...................................... 2

CLEARANCESANDDIMENSIONS.............................. 2

iMPORTANTNOTES............................................. 3

UNPACKINGANDEXAMININGYOURRANGE................. 3

IMPORTANTSAFETYINSTRUCTIONS......................... 3

ELECTRICALCONNECTIONS................................ 4-6

ANTI-TIP .................................................... 6-7

MODELANDSERIALNUMBERLOCATION.................... 8

CARE,CLEANINGANDMAINTENANCE...................... 8

® Insight _"

Summary of content (8 pages)

PAGE 1
30" Slide-in Range I iNSTALLATiON ANDSERVICEMUSTDE PERFORMEDBY A QUALiFiEDiNSTALLER. iMPORTANT: SAVE THiS iNSTALLATiON MANUAL FOR LOCAL ELECTRICAL iNSPECTOR'S USE, READANDSAVETHESEiNSTRUCTiONSFORFUTUREREFERENCE, For SAFETY CONSiDERATiONS do not install a range in any combustible cabinetry accord with the stated clearances and dimensions on page 2. See Figures 1 and 2. which is not in RANGEMEASUREMENTS ...................................... 2 ELECTRICAL CONNECTIONS ................................
PAGE 2
iNSTALLATiON MANUAL If using countertop with integrated drip edge, remove 5/8-inch to make flush as illustrated. 31 1/4" glass and minimum 30" to bottom of cabinet over cooktop 18 _r to upper: cabinets 36_+1/8" to bottom of cooktop surface 23 1/8" *_%_.back Figure 1 contains many range measurements planning your kitchen and/or range location. for reference when 31 1/4" * Provide adequate clearances combustible surfaces.
PAGE 3
iNSTALLATiON _To the range, bracket it must packed with Make sure the wall coverings and the cabinets around the range can withstand the heat generated by the range. ° Before installing the range in an area covered with linoleum or any other synthetic floor covering, make sure the floor covering can withstand heat at least 90°F (32.2°C) above room temperature without shrinking, warping or discoloring. Do not install the range over carpeting unless you place an insulating pad or sheet of 1/4-inch (0.
PAGE 4
iNSTALLATiON MANUAL screw \ The installer or consumer is responsible for connecting the power supply cord to the connection block located behind the back panel access cover. This range may be connected by means of permanent "hard wiring" (flexible armored or nonmetallic shielded copper or aluminum cable), or by means of a power supply cord kit. Only a power supply cord kit rated at 240 volts or 208 volts and 50 amperes and marked for use with ranges shall be used.
PAGE 5
iNSTALLATiON 3 & 4-WIRE 4-WIRE CONNECTION 3-_ ire permanent 4-wire permanent iNSTRUCTiONS 2 Follow the power supply kit manufacturer's Installation Instructions supplied with the strain relief clamp and install. See Figure 8. 4 5 2 Strip insulation away from the ends of the permanent wiring for line 1, line 2 and neutral; also strip ground wire on 4-wire connections. Tighten all 3 or 4-wire leads to the terminal block. Follow wire locations shown in Figure 11.
PAGE 6
iNSTALLATiON MANUAL o NORMAL INSTALLATION ANTI-TIP _ _ect/terminNblock To reduce Connect I_ne 1 here. Ground Note: clamp always center strap ii_i;!!_ INSTRUCTIONS WARNING the risk of tipping of the range, the range installed Anti-Tip with the range. to install the Anti-Tip Failure to tip over if excessive a child climbs liquids or from upon weight it.
PAGE 7
iNSTALLATiON 2 DRILL Drill PILOT a t/S-inch pilot is to be mounted degree screws floors, hole where angle. drill provided 5/t6-inch AND to the wall, dowmvard ceramic HOLES screws drill pilot If bracket a 5/32-inch may be used nut-driver FASTEN pilot or flat head are to be located. hole 1 3/4 inches or concrete screwdriver 20 to masonry deep. material.
PAGE 8
iNSTALLATiON MANUAL The name plate, including model and serial number, is located on the faceplate behind the Microwave Drawer front. Refer to the Operation Manual fbr cleaning instructions. If removing the range is necessary fbr cleaning or maintenance, disconnect the electrical power supply. If the electrical supply is inaccessible, lift the unit slightly at the front and pull out away from the wall. Pull only as far as necessary to disconnect the electrical supply.