KB-0333KS KB-0333KK KB-0333KW SERVICE MANUAL S65H253KB033K INSIGHT RANGE HOOD MODELS KB-0333KS KB-0333KK KB-0333KW TABLE OF CONTENTS Page PRECAUTIONS TO BE OBSERVED BEFORE BEFORE SERVICING ......................... INSIDE FRONT COVER WARNING TO SERVICE PERSONNEL .............................................................................................................. 1 FOREWORD AND WARNING ..............................................................................................................
KB-0333KS KB-0333KK KB-0333KW PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY. 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact Sharp at the address or telephone number listed on page 2 of this manual. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
KB-0333KS KB-0333KK KB-0333KW SERVICE MANUAL PRODUCT DESCRIPTION INSIGHT RANGE HOOD KB-0333KS KB-0333KK KB-0333KW COMPONENT REPLACEMENT FOREWORD PARTS LIST This Manual has been prepared to provide Sharp Electronics Corp. Service Personnel with Operation and Service Information for the SHARP INSIGHT RANGE HOODS, KB-0333KS, KB-0333KK, KB0333KW. It is recommended that service personnel carefully study the entire text of this manual so that they will be qualified to render satisfactory customer service.
KB-0333KS KB-0333KK KB-0333KW PRODUCT SPECIFICATION ITEM DESCRIPTION Power Requirements 120 Volts, 60 Amps 60 Hertz Case Dimensions Width 30" Height 7 1/4" Depth 20" Hood lamps (3 Levels) 2 bulbs (not included) 40W x 2 (Incandescent light bulbs) or 50W x 2 (Halogen bulbs) Hood fan (4 Speeds) Approx. 100 to 430 C.F.M.
FUSE AND SCHEMATIC DIAGRAM FUSE KB-0333KS KB-0333KK KB-0333KW To replace the fuse: The hood control contains a fuse to protect it from power 1. Disconnect power at service entrance. surges. If the fuse has opened (blown), the green fan2. Remove filters, bottom panel, light wire harness and air level indicators will operate properly when the fan chute. buttons/switches are pressed, but the fan and lights will 3 Remove and inspect fuse. If it is not open (blown), additional not turn on.
KB-0333KS KB-0333KK KB-0333KW COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE WARNING : Before servicing or cleaning unit, switch power OFF at service panel and lock the service disconnect to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. LIGHT PANEL and AIR CHUTE REMOVAL/INSTALLATION 1.
CONTROL ASSEMBLY and CONTROL PANEL SERVICING 1. Switch OFF power at service panel, to prevent accidental electrical shock, or damage to components. 2. Remove FILTERS and set aside. 3. Remove two #8 screws (A) attaching BOTTOM COVER (B) to HOOD, tip BOTTOM COVER down and remove. 4. Remove the two #6 (C) and three #8 (D) pan head screws attaching the LIGHT PANEL (E) to the HOOD and lower thE LIGHT PANEL to expose the LIGHT CONNECTOR (F). 5. Disconnect the LIGHT CONNECTOR (F) and set the LIGHT PANEL aside. 6.
KB-0333KS KB-0333KK KB-0333KW PARTS LIST Note: "§" MARK: PARTS DELIVERY SECTION REF. NO. PART NO.
KB-0333KS KB-0333KK KB-0333KW 2 1 4 3 6 5 HOOD PARTS 1 3 A A 3 3 4 2 12 3 5 6 B 31 9 B 8 24 Actual wire harness may be different from illustration.
KB-0333KS KB-0333KK KB-0333KW NOTES: 8
KB-0333KS KB-0333KK KB-0333KW NOTES: 9
KB-0333KS KB-0333KK KB-0333KW COPYRIGHT © 2005 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.