R LUFTREINIGER BEDIENUNGSANLEITUNG PURIFICATEUR D’AIR MANUEL D’UTILISATION Free standing type Freistehende Ausführung Type mobile Vrijstaand type *Plasmacluster is a trademark of Sharp Corporation.
Please read before operating your new Air Purifier The air purifier draws in room air from its air intake, lets the air pass through a Active Carbon Filter (deodorization filter) and a HEPA Filter (dust collection filter) inside of the unit, then discharges the air from its air outlet. The air purifier unit repeats this process by moving its internal fan. As air passes through, a new HEPA Filter can remove 99.97% of dust particles, of as small as 0.3 microns.
ENGLISH CONTENTS Your new air purifier will control the ratio of negative ions and positive ions depending on the condition of the room. • Clean Mode Approximately the same numbers of positive and negative ions are discharged. • AUTO Plasmacluster Ion Mode The unit detects the dust, mold or airborne microbes using its sensors, and controls the generating amount of positive and negative ions automatically. When room air is impure, approximately same numbers of positive and negative ions will be released.
IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic safety precautions should be followed, including the following: WARNING - To reduce the risk of electrical shock, fire or injury to persons: • Read all instructions before using the air purifier. • Use only a 220-240 volt outlet. • Do not use the air purifier if the power cord or plug is damaged or the connection to the wall outlet is loosened. • Periodically remove dust from the power plug.
CAUTIONS CONCERNING OPERATION • Do not block the intake and air outlet. • Do not use the unit near or on hot objects, such as stoves or heaters or where it may come into contact with steam. • Do not lay the unit down when using. • Always hold the handle on the back of the unit when moving it. Holding the front panel when carrying may cause it to detach, thus dropping the unit and resulting in bodily injury. • Do not operate the unit without the filter. • Do not wash and reuse HEPA filter .
PART NAMES MAIN UNIT DISPLAY MIST Unit Indicator Light MIST Unit Reset Button ION SHOWER Indicator Light ION SHOWER Mode Button OFF Timer Display Indicator Lights Plasmacluster Indicator Light Dust Sensor (Dust Sensor Cover) Hook Front Panel Remote Control INCLUDED Remote Control (1 unit) Battery (AAA battery x 2 ) • Operation manual E-4
Remote Control Receiver Power ON/OFF Button Mode Selection Button Fan Speed Indicator Light Pollen Mode Indicator Light AUTO Operation Indicator Light MIST Operation Indicator Light CLEAN-SIGN Light NEDERLANDS Odour Sensor Temperature / Humidity Sensor ENGLISH Front Air Outlet BACK Filter Frame Handle HEPA Filter (white) Active Carbon Filter (black) Rear Air Outlet Pre - Filter Date Label MIST Unit MIST Filter Set • MIST Filter • MIST Filter Frame MIST Tray Cap Float MIST Tray MIST Tray Top P
PREPARATION Be sure to remove the power plug from the wall outlet. FILTER INSTALLATION To maintain the quality of the filters, they are installed in the main unit and packed in the plastic bags. Be sure to remove the filters from the plastic bags before using the unit. 1 Remove the filters Hook 1 Remove the Front Panel. Push in the hooks, then pull the Front Panel. Front Panel 2 Pull out the Filter Frame and remove the Pre-Filter. Filter Frame Pre-Filter the HEPA Filter.
Active Carbon Filter 2 1 Install the filters HEPA Filter Place the HEPA Filter within the Filter Frame. Please make sure that the HEPA Filter is placed in proper orientation. Filter Frame Tabs (4 places) Place the Active Carbon Filter on top of the HEPA Filter with the bands (2 places) facing up. ENGLISH Band the Pre-filter through the 2 Place bands (2 places) located at the corners of the Active Carbon Filter. Holes Insert the tabs of the pre-filter into the associated holes of the Filter Frame.
PREPARATION Pour water into the Tank This product can be used as an air purifier without putting water in the tank. the tank handle and remove the 1 Hold tank. Tank Handle Tank 2 Remove the tank cap and pour water. • Use drinkable tap water. (Generally speaking, tap water is sterilized with chlorine to suppress propagation of bacteria.) • Change the tank water every day with fresh tap water. Tank Cap Tank After supplying water, securely 3 tighten the tank cap.
INSERTING BATTERIES IN THE REMOTE CONTROL the back cover 1 Remove Press and slide the back cover to remove. batteries 2 Insert Insert batteries with shown below. ＋ − − ＋ and as REMOTE CONTROL USE • Operate with the remote control facing the main unit receiver. • The signal range is about 7m. • Make sure there are no objects blocking the path of the signal. • Abeep sound will be heard from the main unit when a signal is received.
OPERATION Main Unit Controls MAIN UNIT OPERATION • • • • • AUTO POLLEN SILENT MEDIUM MAX Mode Selection Button Power ON/OFF Button ION SHOWER Mode Button Operation Mode Indicator Light 1 Power ON/OFF Button • Used to start operation (short beep) and stop operation (long beep) • Plasmacluster Indicator Light and Fan Speed Indicator Light turn on/off. • Unless unplug the power cord, the operation starts in the previous mode the unit was operated in.
Operations available with the Remote Control REMOTE CONTROL OPERATION Transmitter • When you press the POWER ON/OFF Button, a short beep will sound and operation will start in AUTO Mode. • Unless unplug the power cord, the operation starts in the previous mode the unit was operated in. • To stop, press the POWER ON/OFF Button again. A long beep will sound and operation will stop.
OPERATION MAIN UNIT INDICATOR ION SHOWER Indicator Light CLEAN-SIGN Light MIST Unit Indicator Light MIST Operation Indicator Light Plasmacluster Indicator Light MIST Unit INDICATOR LIGHT Clean the MIST Filter when the MIST Filter Indicator Light activates. (The indicator light will be activated in about 1 month, when using the unit with mist operation 24 hours day, every day.) (See Page E-14) ION SHOWER INDICATOR LIGHT The ION SHOWER Operation is working when the ION SHOWER Indicator Light activates.
Very Impure (Red) ABOUT THE CLEAN-SIGN • The condition of the CLEAN-SIGN depends on the room air condition detected by the Dust and Odour Sensors when the plug is inserted into the wall outlet. • It is possible to have a green CLEAN-SIGN with impurities in the air at the time that the air purifier was just introduced to the room environment. After a while, however, the base impurity rate will be adjusted to detect room air condition correctly.
CARE AND MAINTENANCE To maintain optimum performance of this air purifier, please clean the unit including the sensor and filters periodically. When cleaning the unit, be sure to unplug the power cord, and never handle the plug with wet hands. Electrical shock and/or bodily injury may occur as a result. MIST UNIT Care Cycle 2 weeks The MIST Filter Indicator Light up.
the MIST Tray Cap back on 7 Put to close it. Make sure that the cap is closed by pushing the whole circumference of the cap. Failure in closing the cap completely may result water spills. When using lemon juice, it is recommended to presoak longer than citric acid. MIST Filter MIST Tray 8 Attach the MIST Filter set to the MIST Tray. NEDERLANDS Do not take the MIST Filter out of the MIST Filter Frame.
CARE AND MAINTENANCE TANK Care Cycle Every day With a small amount of water inside and the tank cap closed, wash the tank set by shaking it. When using a kitchen detergent, dilute the detergent with water and rinse it thoroughly. Tank WASHABLE ACTIVE CARBON FILTER CARE HAND WASH ONLY! DO NOT TUMBLE DRY! Care Cycle 2 months a large container with warm the filter outdoors 5 Dry 1 Fill water, add a mild kitchen detergent if possible in a well and stir. ventilated area.
MAIN UNIT Care Cycle 1 month To prevent dirt or stains on the main unit, clean as often as necessary. If stains are allowed to remain, they may become hard to clean. Wipe with a dry, soft cloth For stubborn stains or dirt, use a soft cloth dampened with warm water. Do not use volatile fluids Benzene, paint thinner, polishing powder, etc., may damage the surface. Do not use detergents Detergent ingredients may damage the unit.
CARE AND MAINTENANCE FILTER REPLACEMENT GUIDELINES The replacement period differs depending on the room environment, the usage hours and location of Air Purifier. If dust or odours persists, replace the filters. (Refer to “Please read before operating your new Air Purifier”) HEPA Filter / Washable Active Carbon Filter Up to 5 years after opening Guide for filter replacement timing • Filter life can be greatly reduced in poor environments.
TROUBLESHOOTING Before calling for repair, please review the list below, since the problem may not be a unit malfunction. Odours and smoke are not removed. • Clean or replace the filters if they appear to be heavily soiled. (Refer to E-16,E-18) The CLEAN-SIGN Light lights green even when the air is impure. • The air could be impure at the time the unit was plugged in. (Refer to E-12) Pull out the plug from the electrical outlet, and insert the plug one minute later.
TROUBLESHOOTING REMEDY (not a malfunction) SYMPTOM Though Clean Sign Indicator turns on Green, Plasmacluster indicator Light terns on blue. • ”SENTINEL” function is working. When the Plasmacluster ion mode is AUTO or CLEAN mode and the unit detects the air environment is favourable for activation of mold, virus, and allergen, using its 4 sensors for dust, odour, temperature and humidity, the Plasmacluster Ions will be automatically increased and controls the activity of airborne microbes.
A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! *) Please contact your local authority for further details. If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal. For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t purchase a new product.
SERVICE PROCEDURE / SERVICE VORGEHENSWEISE SERVICE PROCEDURE - ONLY EFFECTIVE IN GERMANY Dear SHARP customer, SHARP machines are proprietary articles which are produced with precision and care according to most modern production methods. In case of proper handling and with considering of the instruction book, this machine will serve you well for a long time. Of course, a defect cannot be ruled out.
SHARP CORPORATION OSAKA, JAPAN Printed in Japan TINS-A193KKRZ JP 06AK
