UX-510UA FO-1470U SERVICE MANUAL No. 00ZUX510UASME FACSIMILE UX-510A MODEL FO-1470 SELECTION CODE U Illustration: UX-510UA open DESTINATION U.S.A. LCR www.OpenLCR.com CONTENTS CHAPTER 1. GENERAL DESCRIPTION [1] Specifications ............................................ [2] Operation panel ......................................... [3] Transmittable documents .......................... [4] Installation ................................................. [5] Quick reference guide .......................
UX-510UA FO-1470U CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.
UX-510UA FO-1470U CHAPTER 1. GENERAL DESCRIPTION [1] Specifications Automatic dialing: Rapid Key Dialing: 36 numbers Speed Dialing: 63 numbers Imaging film: Initial starter roll (included with machine): Approx. 60 letter-size pages Replacement roll: UX-15CR/FO-15CR (One roll yields approx. 500 letter-size pages) Effective scanning width: 8.2" (208 mm) max. Effective printing width: 8.1" (206 mm) max. Contrast control: Automatic/Dark selectable Reception modes: TEL/FAX/A.M. (Note: A.M.
UX-510UA FO-1470U [2] Operation panel 1 2 3 4 5 6 7 TEL FAX ABC 1 GHI 2 JKL 4 PQRS DEF 3 MNO 5 TUV 7 SPEED DIAL 8 02 03 19 20 21 04 05 06 07 22 23 24 25 08 09 10 11 26 27 28 29 12 13 14/POLL 15/P1 30 31 32 33 16/P2 17/G1 18/G2 34 35 36 REDIAL VOLUME DOWN UP 6 WXYZ 01 SHIFT A.M. 8 HOLD/ SEARCH 9 RECEPTION MODE FUNCTION RESOLUTION COPY/ HELP START MEMORY STOP SPEAKER 0 OpenLCR OpenLCR PANEL RELEASE 18 17 16 15 14 13 12 1.
UX-510UA FO-1470U [3] Transmittable documents 5. Automatic Document Feeder Capacity 1. Document Sizes Number of pages that can be placed into the feeder at anytime is as follows: Normal size width 5.83" – 8.5"(148 – 216 mm) Normal size: max. ADF 20 sheets length 5.04" – 11"(128 – 279 mm) Special size: single sheet only (manual feed) NOTES: (Max.) (Min.) 128mm 148mm (Max.
UX-510UA FO-1470U 7. Use of Document Carrier Sheet TELEPHONE JACK A document carrier sheet must be used for the following documents. A standard RJ11C telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices. • Those with tears. • Those smaller than size 5.83" (W) x 5.04" (L) (148 mm (W) x 128 mm (L)).
UX-510UA FO-1470U 3 Take the new film out of its package, and insert two of the gears 7 Insert the empty spool into the back of the compartment so that the provided with the fax into the ends of the spool with film. Make sure that the two tabs on the gears fit properly into the slots in the ends of the spool. • gear and the flange fit into the slots on the sides of the compartment. • Make sure that the gear engages with the gear below it. Do not yet remove the band which holds the spools together.
UX-510UA FO-1470U 4 Insert the paper tray into the back of the fax as shown. 3. Assembly and connections 1 Plug the power cord into a 120V, 60Hz, grounded(3-prong) outlet. • Caution: Do not plug the power cord into any other kind of outlet. This will damage the machine and is not covered under the warranty. • The machine does not have a power on/off switch, so the power is turned on and off by simply plugging in or unplugging the power cord.
UX-510UA FO-1470U 3 Pull the paper release plate toward you and insert the stack of paper 5 The fax has been set at the factory to scale the size of received faxes into the tray, print side down. • to letter size paper. If you have loaded legal paper, you must change the paper size setting to legal. Press these keys: If paper remains in the tray, take it out and combine it into a single stack with the new paper before adding the new paper.
UX-510UA FO-1470U 2 Remove the imaging film from the printing compartment and set it on 5 Wind the film slightly (rotate the gear on the right side of the rear 3 Gently pull the jammed paper out of the printing compartment. 6 Close the print compartment cover, making sure it clicks into place. a sheet of paper. spool) so that there is no slack in the film. Make sure that both edges of the film wind onto the spool evenly.
UX-510UA FO-1470U SENDING FAXES [5] Quick reference guide ENTERING YOUR NAME AND NUMBER 1. Press: FUNCTION 3 Display shows: OWN NUMBER SET Place your document (up to 20 pages) face down in the document feeder. START 2. Press: 3. Enter your fax number (max. of 20 digits) by pressing the number keys. ♦ To insert a space between digits, press the # key. ♦ If you make a mistake, press the SPEED DIAL key to backspace and clear the mistake. START 4. Press: 5.
UX-510UA FO-1470U MEMO 1 – 10
UX-510UA FO-1470U CHAPTER 2. ADJUSTMENTS 3. Settings (1) Dial mode selector [1] Adjustments DIAL mode (Soft Switch No. SWB4 DATA No. 3) (step 1) Select "OPTION SETTING". General KEY : FUNCTION Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary. DISPLAY: OPTION SETTING 4 PRESS OR # (step 2) Select "DIAL MODE". 1. Adjustments KEY: Push # until " DIAL MODE " is indicated because the number of # s changes by the model.
UX-510UA FO-1470U [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC → 9 → ROM Ver. FPS0 → 8 → # → 7 , and the following display will appear. After 2 sec: DIAG MODE FPS0 Then press the START key. Select the desired item with the key or the # key or select with the rapid key. Enter the mode with the START key.
UX-510UA FO-1470U 3. Diagnostic items description 3. 1. Soft switch mode 3. 6. Signal send mode This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker when the line monitor of the soft switch is on. Used to change the soft switch settings. The soft switch which is stored internally is set by using the keys. The available soft switches are SW-A1 to SW-N3.
UX-510UA FO-1470U 3. 12. Entry data receive In this mode, the registered data sent from the other machine is received and the received data is registered in the machine. When this mode is used for receiving, the other machine must be in the entry data send mode. After receiving is completed, the following lists are printed. 1. Telephone list data 2. Sender register data (The passcode No. is also printed if the polling function is provided.) 3. Optional setting list 4. Soft switch content 5.
UX-510UA FO-1470U 5. Soft switch description • Soft switch SW NO. SW l A1 DATA NO. Switch setting and function ITEM 1 Initial setting 0 1 Protect from echo No Yes 2 Forced 4800 BPS reception Yes No 0 3 Footer print Yes No 0 4 Length limitation of copy/send/receive No limit Copy/send: 1m 0 Remarks 0 Receive: 1.
UX-510UA FO-1470U SW NO. SW l A6 DATA NO.
UX-510UA FO-1470U SW NO. DATA NO. 1 Switch setting and function ITEM 1 DTMF signal transmission level (High) 2 SW l B6 No. = Binary input 0 16 8 4 2 1 0 1 2 3 4 5 0 0 1 1 1 1 1 3 4 5 6 Dial tone detection (LCR center call) 7 8 Reserved Reserved No Yes 0 0 0 Factory Light Dark setting No. 1 0 1 0 1 0 No. 2 0 Factory 0 Light 1 Dark 1 Darker in 0 setting dark 3 No. 3 0 1 0 1 0 4 No.
UX-510UA FO-1470U SW NO. SW l E1 SW l E2 SW l E3 DATA NO.
UX-510UA FO-1470U SW NO. SW l G2 DATA NO. Switch setting and function ITEM 1 1 2 Reserved Reserved 0 0 3 4 Reserved Reserved 0 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Reserved 1 2 3 4 No. 1 No. 2 100ms 200ms 300ms 0 0 0 1 1 0 1 1 0 1 0 Reserved 0 Selection time of quiet detection 30s 40s 50s 60s 5 No. 5 0 0 1 1 0 6 No.
UX-510UA FO-1470U SW NO. SW l I3 SW l I4 SW l I5 SW l I6 SW l I7 SW l J1 DATA NO.
UX-510UA FO-1470U SW NO. DATA NO. Switch setting and function ITEM 1 Speaker volume (3 stages) 1 2 3 SW l J2 Polling key Low Middle High 0 0 1 1 1 No. 2 0 1 0 1 0 No Handset receiver volume 5 SW l J3 Low No. 1 Yes 4 Initial setting 0 OPTION 0 Low Low Middle High No. 4 0 0 1 1 No.
UX-510UA FO-1470U SW NO. SW l M2 DATA NO. Switch setting and function ITEM 1 1 Reserved 0 2 3 Reserved Reserved 0 0 4 Reserved 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Reserved 0 1 LCR short time 2 SW l N1 Initial setting 0 No. = 3 4 Binary input 0 32 16 8 4 2 1 0 1 0 2 3 4 5 0 0 0 1 6 0 5 1 0 7 Reserved 0 8 Reserved 0 1 LCR long time 2 No.
UX-510UA FO-1470U SW-A2 No. 8 CNG transmission • Soft switch function description When set to "0" , this model allows CNG transmission by pressing the Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case. CNG transmission can be performed in the auto dial mode. SW-A1 No. 1 Protect from echo Used to protect from echo in reception. SW-A1 No. 2 Forced 4800BPS reception SW-A3 No. 1, No.
UX-510UA FO-1470U SW-A5 No. 5, No. 6 Digital cable equalizer setting (Reception for Caller ID) SW-B2 No. 7, No. 8 Reserved Set to "0". Line equalization when reception for CALLER ID is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station. SW-B3 No. 1 ~ No. 5 Reserved Set to "0". SW-A5 No. 7 Error criterion SW-B3 No. 6, No.
UX-510UA FO-1470U SW-B6 No. 6 Dial tone detection (LCR center call) Used to set YES/NO of dial tone detection (calling LCR center). Phone Number Intended Purpose SW-B6 No. 7, No. 8 Reserved Ring Pattern Set to "0". SW-C1 No. 1, No. 2 Reading slice (Binary) Used to determine the set value of reading density in standard/fine mode. The standard setting is "00" (Factory setting is "00") SW-C1 No. 3, No.
UX-510UA FO-1470U SW-D2 No. 4 Reserved SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL (0 ~ 9) Set to "0". Used for Caller ID function. Remote operation codes can be changed from 0 through 9. If set to greater than 9, it defaults to 9. The "5 " is not changed. Ex-7 (Default: 5 ) SW-D2 No. 6 Caller ID detect during CI off SW-F2 No.
UX-510UA FO-1470U SW-H1 No. 3, No. 4 Busy tone detection ON/OFF time (Upper duration) SW-I7 No. 1 ~ No. 8 Reserved Set to "0". Similarly to SW-H1 No. 1, the set value can be varied. SW-J1 No. 1 Activity report print The upper limit can be set in the range of 650msec to 2700msec. This soft switch is used to select: whether or not to print out the activity report when the memory is full. An activity report can be printed when the following key entry command is made. SW-H1 SW-H1 SW-H1 SW-H1 No.
UX-510UA FO-1470U SW-N3 No. 5, No. 6 Digital egualization setting (Recept for LCR V23 mode) SW-L1 No. 5 Cut off mode (COPY mode) Whether the excessive part is printed on the next recording paper or discarded is selected to copy a document which is longer than the recording paper. Line egualization when Open LCR table download is to be set according to the line characteristics. Setting should be made according to distance between the telephone and the telephone company central switching station. SW-L1 No.
UX-510UA FO-1470U [3] Troubleshooting Refer to the following actions to troubleshoot any of the problems mentioned in 1-4. [1] A communication error occurs. [2] Image distortion produced. [3] Unable to do overseas communication. [4] Communication speed slow due to FALLBACK. • Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [1] [2] [3]. • Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5. May be used in case [3].
UX-510UA FO-1470U [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) 0 Incomplete signal frame Cannot recognize bit stream after flag 1 NSF, DIS Cannot recognize DCS signal by echo etc.
UX-510UA FO-1470U 3-2. Automatic document feed CHAPTER 3. MECHANISM BLOCKS 1) Use of the paper feed roller and separation rubber plate ensures error-free transport and separation of documents. The plate spring presses the document to the paper feed roller to assure smooth feeding of the document. ,,, , [1] General description 2) Document separation method: Separation rubber plate 1.
,, , , UX-510UA FO-1470U 5. Optical system Paper feed spring Separation rubber Last page of document (1) General view Rear sheet CCD PWB Document Red mark LED lamp First page of document Paper feed arm Reader glass Mirror 2 Paper feed roller Fig. 4 Mirror 3 CCD Lens Mirror 1 Fig. 5 3-5. Documents requiring use of copy 1) Documents smaller than 128mm x 148mm. (2) Composition 2) Documents thinner than the thickness of 0.06mm.
UX-510UA FO-1470U 6. Recording block (1) General view Take-up side Imaging film Platen roller Pinch roller Guide shaft Thermal head Paper guide PO roller U turn guide Supply side RP hopper Rotation plate Main frame PU roller Separate plate Film sensor lever P-IN sensor lever Fig. 7 6-1.
UX-510UA FO-1470U [2] Disassembly and assembly procedures • This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures. • Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units, refer to the Parts List. • The numbers in the illustration, the parts list and the flowchart in a same section are common to each other.
UX-510UA FO-1470U 2 Parts list (Fig. 2) Document guide upper No. Q’ty No.
UX-510UA FO-1470U 3 Parts list (Fig. 3) Operation panel No. rib Panel PWB Part name Q’ty 1 Operation panel unit 1 2 Screw (2.6×6) 5 3 Insulation sheet 1 4 Operation panel PWB unit 1 5 12 key 1 6 Start key 1 7 Stop key 1 8 Mode key 1 9 Direct key 1 10 Panel cable 1 11 Operation panel 1 2 3 Note) Keep the panel PWB to under the rib like a picture.
UX-510UA FO-1470U 4 Parts list (Fig. 4) Top cover and head frame unit No. 1 Part name Q’ty 1 Mechanism unit 1 2 Top cover unit 1 3 Screw (3×10) 5 4 Head frame unit 1 5 Hopper guide, right 1 6 Hopper guide, left 1 7 Screw (3×6) 1 8 Pinion gear 1 9 Hopper spring 1 10 Top cover 1 Confirm of HOPPER GUIDE position.
UX-510UA FO-1470U 5 Parts list (Fig. 5) Head frame and thermal head No. 1 4 6 15 2 5 7 16 8 17 9 18 10 19 11 20 3 Part name Q’ty No.
UX-510UA FO-1470U 6 Parts list (Fig. 6) Paper out guide No. Part name Q’ty 1 Mechanism unit 1 2 Screw (3×10) 2 3 Paper out guide unit 1 4 Idler gear A 1 5 Take-up gear 1 6 Slip gear ass’y 1 7 Cut washer 1 8 Film shaft C 1 9 PO pinch roller spring 2 10 PO pinch roller 2 11 Paper out guide 1 1 2 9 3 10 4 5 9 10 6 7 8 2 9 10 7 11 3 9 4 10 11 8 5 6 1 Fig.
UX-510UA FO-1470U Parts list (Fig. 7) Recording paper hopper, speaker and pinch roller 7 No. 1 2 14 18 3 15 19 4 16 20 5 17 21 6 Q’ty No.
UX-510UA FO-1470U Parts list (Fig. 8) Main frame unit, ROM cover, memory cover, drive unit and optical unit 8 No. Q’ty 1 Mechanism unit 1 2 Screw (3×10) 1 3 ROM cover 1 4 Memory cover 1 5 Screw (3×10) 1 6 Drive unit 1 7 Screw (3×10) 3 8 Main frame unit 1 9 Optical unit 1 2 1 2 Part name 4 3 4 3 7 8 5 9 6 7 7 8 5 6 9 1 Fig.
UX-510UA FO-1470U 9 Main frame, U turn guide and transfer roller etc. Parts list (Fig. 9) No. Q’ty No. Q’ty No.
UX-510UA FO-1470U 10 Parts list (Fig. 10) Drive unit frame No. Q’ty No.
UX-510UA FO-1470U 11 Parts list (Fig. 11) Optical frame No. 1 4 7 10 3 5 8 11 6 9 12 No. Optical unit Part name 1 7 Reader glass 1 2 Screw 2 8 LED 1 3 CCD PWB unit 1 9 Shading sheet 3 2 4 Shading sheet 1 10 Mirror 3 1 5 Lens holding spring 1 11 Mirror 1 1 6 Lens 1 12 Mirror 2 1 13 Optical frame 1 7 9 2 Q’ty 1 Part name Q’ty 4 5 8 Red( ) 9 6 2 Blue ( ) 13 3 10 13 11 12 Face of reflect 1 Fig.
UX-510UA FO-1470U 12 Parts list (Fig. 12) PWB section No. Q’ty No. 1 Mechanism unit Part name 1 7 Connector 2 Screw (3×6) 1 8 Control PWB unit 1 3 TEL/LIU ARG cable 1 9 TEL/LIU PWB unit 1 4 Screw (4×6) 1 10 Power supply PWB unit 1 5 AC cord 1 11 Earth plate 1 6 Screw (3×10) 6 12 Jack sheet 1 1 2 3 2 6 8 9 5 10 6 11 7 5 6 8 9 3 6 6 7 12 Hook 6 PWB 11 12 Note) The PWB hook to cabinet. 1 Fig.
UX-510UA FO-1470U 13 Parts list (Fig. 13) Wire treatment No. Part name 1 Band (Black) CCD cable LED cable Q’ty 1 No.
4–1 EXT.TEL LINE HANDSET SPEAKER DRAM 4Mbit SURGE PROTECT/ FILTER AMPLIFIER AMPLIFIER CML AMPLIFIER INTEGRATED ANALOG DEVICE (20415) CONTROL PWB UNIT [1] Block diagram CI TRANSFORMER AMPLIFIER CLOCK 32.256MHz BZ TEL/LIU PWB UNIT CLOCK 32.768kHz VBT +3.
SPEAKER HANDSET TEL LINE EXTERNAL LINE [2] Wiring diagram CNLIUA 2 TEL/LIU PWB UNIT CNHJ CNLNJ 14 4–2 LED ARRAY 2 CNLED CNSP CNLIUA CCD PWB 7 CNCCD THERMAL HEAD 16 CNTH CONTROL PWB UNIT CNPN 15 TX/RX MOTOR 2 POWER SUPPLY PWB OPERATION PANEL PWB 6 CN2 CNPN CNMT CNCS CNPW 6 CNLCD 14 LCD UNIT CAM SW.
UX-510UA FO-1470U [3] Point-to-point diagram CNMT TX/RX MOTOR THERMAL HEAD OPERATION PANEL PWB CCD PWB TPBD TPAD TPBD TPAD VMT VMT VTH VTH STRB1 STRB2 THI N.C.
UX-510UA FO-1470U 3. Operational description CHAPTER 5. CIRCUIT DESCRIPTION Operational descriptions are given below: • [1] Circuit description When a document is loaded in standby mode, the state of the document sensor is sensed via the 1 chip fax engine (SCE114). If the sensor signal was on, the motor is started to bring the document into the standby position. With depression of the START key in the offhook state, transmission takes place.
UX-510UA FO-1470U 3) 27L2000 (IC4): pin-32 DIP (ROM) [2] Circuit description of control PWB ROM of 2Mbit equipped with software for the main CPU. 1. General description 4) W24258S-70LE (IC8): pin-28 SOP (SRAM) Fig. 2 shows the functional blocks of the control PWB, which is composed of 5 blocks. Line memory for the main CPU system RAM area and coding/decoding process. Used as the transmission buffer. MAIN CONTROL BLOCK Memory of recorded data such as daily report and auto dials.
UX-510UA FO-1470U SCE114 (IC9) Terminal descriptions Pin No.
UX-510UA FO-1470U SCE114 (IC9) Terminal descriptions Pin No.
UX-510UA FO-1470U SCE114 (IC9) Terminal descriptions Pin Pin List No.
UX-510UA FO-1470U (2) Panel control block The following controls are performed by the SCE114.
UX-510UA FO-1470U (4) Modem (SCE114/20415) block FEATURES INTRODUCTION • The CONEXANT SCE114 modem is a synchronous 14400 bits per second (bps) half-duplex modem with error detection and DTMF reception. It has low power consumption and requires +5V and +3.3V DC power supply. The modem can operate over the public switched telephone network (PSTN) through line terminations provided by a data access arrangement (DAA). The SCE114 is designed for use in Group 3 facsimile machines.
UX-510UA FO-1470U [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description INTEGRATED ANALOG 20415 1) Block diagram TEL/LIU PWB SP OUT ENABLE CONTROL PWB TXOUT RTLOOP SPKRP-P L1 C CML M (0:1) (1:0) (0:0) (1:1) MIC ENABLE SIN DAC SP DRIVER L2 DAC GAIN 0,6dB B CI RXIN MIC GAIN MICP MIC IN LPF MIC 1 ENABLE 0 0,20,25,30dB ADC SOUT LINE IN TELIN LINEIN LINE IN LPF 1 ENABLE 0 ADC GAIN 0,–4dB HANDSET RX TELMUTE TX RCV VOL DTMFMUTE LINE DRIVER TELOUT LNINSEL
UX-510UA FO-1470U 5. Externally connected TEL OFF HOOK detection circuit section • 4) Signal selection The following signals are used to control the transmission line of TEL/ FAX signal. For details, refer to the signal selector matrix table. The circuit current detection is turned on together with OFF HOOK of main body or OFF HOOK of externally connected TEL. ON of CML OFF (HS=L) is judged as OFF HOOK of externally connected TEL. [Control signals from output port] Signal Name 6.
UX-510UA FO-1470U [Signals for status recognition according to input signals] No. Signal Name (CNLIUA) No. Signal Name (CNLIUA) 1 PE1 8 TXOUT H:The handset is in the on-hook state. 2 TEL OUT 9 RXIN L: The handset is in the off-hook state. 3 TEL IN 10 RHS Incoming call (CI) detection signal H: Door open. 4 5 TEL MUTE 11 DOOR SW CI 12 +5V L: Door close.
UX-510UA FO-1470U [4] Circuit description of power supply PWB 1. Block diagram 2.5A/125V Noise Filter Circuit AC IN Rectifying Smoothing Circuit Switching Circuit (RCC system) Regulator Circuit +5V +24V FUSE 4A/72V Control Circuit Photo Coupler Fig. 8 2-1. Noise filter circuit 2-4. Control circuit The input noise filter section is composed of L1 and C1, C15, which reduces normal mode noise from the AC line and common mode noise to the AC line.
6–1 CNPN-4 CNPN-3 A KEN1A KEN2A KEN3A R189 R198 0 0 DG B 2Y1 2Y2 2Y3 2Y4 1 1OE 19 2OE 9 7 5 3 1Y1 1Y2 1Y3 1Y4 11 13 15 17 2 4 6 8 GND 10 VCC 20 2A1 2A2 2A3 2A4 1A1 1A2 1A3 1A4 IC2 HCT244 C R130 270 1 4 10 13 12 9 5 2 1OE 2OE 3OE 4OE 1A4 1A3 1A2 1A1 GND VCC 1Y4 1Y3 1Y2 1Y1 7 14 11 8 6 3 IC3 LV125A DG VIDCNT1 (3-1A) RA 5 470 4 3 2 1 +5V DG DG C128 1 5 6 7 8 49 R125 10K RA 6 470 D +3.3V DG C127 1 R128 270 DG E 2.2 C159 N.M. RA 11 1K DG DG DGA F +3.
6–2 D[7:0] A[18:0] B 27L020 OE 24 GND 16 C DG C100 0.1 +3.3V D0 D1 D2 D3 D4 D5 D6 D7 (1-4D) CE2 (1-3I) WR (1-3I) CE1 D R115 22K VBT N.M. R118 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 E R119 0 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 11 12 13 15 16 17 18 19 VSS 14 VCC 28 IO1 IO2 IO3 IO4 IO5 IO6 IO7 IO8 W24258 22 CS2/OE 27 WE 20 CS1 10 9 8 7 6 5 4 3 25 24 21 23 2 26 1 F C129 0.1 DG VBT D0 D1 D2 D3 D4 D5 D6 D7 (1-3I) DWR (1-3I) CAS0 (1-3I) RAS +3.
6–3 1 2 3 4 5 (6-2F) VOL-A (6-2F) VOL-B (6-2F) VOL-C (5-3E) VTHON (1-2A) VIDCNT1 CNLIUB-1 CNLIUB-3 (5-4F) LEDON (6-2E) CML CNLIUA-7 CNLIUA-4 (5-1A) PNLON (4-5D) RBNSNS CNPW-7 (4-3D) FRSNS (4-3D) ORGSNS CSWI DRSNS (4-6D) (4-5D) CNLIUB-4 CNLIUB-2 CNLIUB-5 (6-1E,5E) RCVOL (5-6A) GCONT SPMUTE (6-4F) CNLIUA-10 (4-4D) PINSNS CNLIUA-1 CNLIUA-6 CNLIUA-5 A C208 N.M.
6–4 A CNPN-8 C108 +3.3V 1K (1W) R1 DG DG 2 1 2 1 DG B N.M. R206 270 N.M. R173 270 N.M. N.M. DGA 270 R108 XC61AN OUT 1 IC 100 R120 51K C106 C119 270 R109 SG206S PI 1(P-IN) SG206S PI 2 (INK) C202 R122 3 VCC DG DG C181 2 RESETO ORGSNS FRSNS <+24V> DOOR SW CSW GND 1 2 3 CNPN-9 +24V CNLIUA-11 CNCSW-1 4 3 4 3 B DG DG R121 DG DG DG C DG Q 103 R112 E C C105 100P C107 100P C180 100P N.M.
6–5 1 2 3 4 5 R177 VO R176 33K IC10 HCT04 6Y 12 13 6A (3-2A) PNLON 5Y 10 DG E Q102 C B +5V R110 DG B 4Y 8 9 4A 11 5A (1-4A) START B 470 R155 3Y 6 5 3A (1-4A) CLK2 DG 0 L112 2Y 4 3 2A (1-4A) CLK1 1 C223 270 GND 7 C184 N.M C N.M. Q101 C166 C 470 C154 0.1 DG C185 0.1 0 L116 N.M. +24V R154 E DG VG + C7 100/50 R152 R111 DG VIDCNT1-A (1-1A) DG BC3 NJM318 5 4 V– (1-4A) CLK1 14 VCC C182 0.
6–6 1 2 3 4 CNLIUA-3 N.M. ZD101 CNLIUA-9 A TELIN DG RXIN TXOUT TELOUT N.M. 39K R179 1 0.1 C189 R161 0 0.1 C188 R180 C171 R162 B DG 184 100K 8 7 C R185 220P C E 0 DG C Q104 RNC1402 0 0 L118 1 N.M. C168 Q105 RNC1402 B DG B 0 R208 IC14 3 2 N.M. R163 E Q109 N.M. C 0 C196 R182 4.7K DG +5VA DG C211 N.M.
UX-510UA FO-1470U Control PWB parts layout (Top side) 6–7
UX-510UA FO-1470U Control PWB parts layout (Bottom side) 6–8
6–9 1 CNHJ-3 CNHJ-2 CNHJ-1 CNHJ-4 TLJ-1 CNLNJ-5 CNLNJ-4 RX– A RX+ TX– TX+ JP2 AR1 RA-391P JP10 R137 0 N.M. JP4 JP8 N.M. L2A L3 R-5C JP9 JP11 JP12 N.M. JP1 L7 R-5C JP15 ARG B D4 DG C9 22/50 DG N.M. C123 0.1 B M L8 JP16 C8 0.82 DG +5V C R134 1K ZD1 JUMPER N.M. R127 150 Q105 2SC2412K N.M. C122 R141 0 CML1 C13 22/50 N.M. R142 D3 C N.M. VREF N.M. N.M. L1 R-5C C128 C129 DG L5 R-5C JP14 N.M. DG R128 1K AR2 N.M.
6 – 10 1 2 3 4 5 6 B A +5V K A +5V R102 R101 DG R3 E PE1 C B SW1 HOOK SW SW2 HOOK SW TP1 DG DG N.M. DPON DOOR SW RHS PE1 HS CI DPMUTE TP2 N.M. N.M. C103 DG PC1 DG C121 DG PC5 C120 DG DG DG Q101 Q103 PC4 TLP521 PC2 PC3 TEL/LIU PWB circuit A C CNLIUA-11 CNLIUA-10 CNLIUA-1 CNLIUA-6 CNLIUA-5 N.M.
UX-510UA FO-1470U TEL/LIU PWB parts layout (Top side) 6 – 11
UX-510UA FO-1470U TEL/LIU PWB parts layout (Bottom side) 6 – 12
6 – 13 1 2 3 4 5 6 B A N.M. C1 0.1 L1 ELF15N005 C25 0.1 C15 1 CN1 3 V1 S07K150GA R1 2.2M(1/2W) F1 2.5A/125V DS1 S1WB60 B R9 470 Q3 2SC1741 C3 680P C2 150/220 R10 0.15(1W) R8 47K N.M. ZD1 Q1 FS5KM-14 R3 470K R2 470K [3] Power supply PWB circuit A C5 4700P Q2 2SC4115 C4 R4 1500P 560 R24 100K N.M. C7 C26 3300P D5 1SS355 D6 PC1 PC2501-1L R7 180 R6 47K R5 6.8K C24 270P C23 4700P D 3 2 6 4 D N.M. C6 0Ω D9 ERA22-06-V3 ZD6 JUMPER C17 1000P ZD2 RD4.
UX-510UA FO-1470U Power supply PWB parts layout (Top side) Power supply PWB parts layout (Bottom side) C12 R16 R13 ZD5 R17 R18 R4 C24 R5 R6 ZD2 R15 R14 D5 R7 C6 C4 C17 ZD1 R9 ZD8 J14 D51 6 – 14
C SH DOS SS OS 3 2 6 – 15 D OD B NS 4 A RS F2802XH-Z8 Φ2 1 E NC 1 NC Φ1 5V NC V0 F NC CCD PWB parts layout F NC AG 22 NC CN1-3 21 NC 2 20 NC R1 2.2K 19 NC C2 0.
6 – 16 C1 0.022 11 12 13 1 2 3 4 5 10 R4 100K R11 1K R10 6.2K VO R7 100K R6 100K R3 100K R2 100K R1 100K 7 4 1 COPY D CNLCD-6 CNLCD-5 CNLCD-3 CNLCD-2 CNLCD-1 A B C D NOTE: Since the parts of PWB cannot be supplied, change it as a unit. C2 22/50 GND 8 16 VCC A0 D1 A1 D2 A2 D3 A3 D4 D5 N.C D6 D7 D8 D9 +5V D5 1SS133 D4 1SS133 D3 1SS133 D2 1SS133 D1 1SS133 R5 100K +5V GND GND E 9 7 6 14 15 C5 0.022 IC1 74HC147 C3 0.022 KEN 1A KEN 2A KEN 3A KEN 4A C4 0.
UX-510UA FO-1470U CHAPTER 7.
UX-510UA FO-1470U [2] Power on sequence START CPU initialized MODEM initialized “WAIT A MOMENT” display STOP key ? NO “MEMORY CLEAR ?” display NO 3 sec ? YES 1 YES STAND-BY START key ? NO 2 YES COPY key ? 1 2 “MEMORY CLEARED” display “MEMORY CLEARED” display Memory clear Memory clear STAND-BY PROCESS CHECK MODE NO YES STOP key ? NO 3 sec ? NO YES STAND-BY 7–2
UX-510UA FO-1470U CHAPTER 8. OTHERS [1] Service tools 1. List NO.
UX-510UA FO-1470U 2. Description 2-1. Extension board unit 1. Remove the TEL/LIU PWB, control PWB and Power Supply PWB from this unit, and mount the extension board unit instead. • Before connecting the wiring to the extension board unit, set the test PWB switches to the fixed position. 2. The setting is as follows. A set with a mounted extension board unit Connector Cable Cable Cable color CNSNS Connected to (PWB) CNPN2 QCNW-4723SCZZ 1. Brown CNTH2 CCNW-4759SC01 2.
UX-510UA FO-1470U H Lightly loosen the red screws of the CCD PWB and obtain the VID 2-2. Scan optical system adjustment signal waveform in synchronization with φT signal waveform. Adjust the CCD PWB positioning to obtain the waveform as shown below. (1) Outline The adjustment procedures of the scan optical system are described below: Scan adjustment jig (2) Adjustment procedures 1 Switch off the machine and disconnect the AC power cable from the wall socket.
UX-510UA FO-1470U [2] IC signal name CONTROL PWB UNIT IC1: VHiTD62001AP1 (TD62001AP) IC8: VHiW24258S7LE (W24258S-70LE) (TOP VIEW) O1 O2 O3 O4 O5 O6 O7 COM 16 15 14 13 12 11 10 9 A14 1 28 VDD A12 2 27 WE A7 3 26 A13 A6 4 25 A8 A5 5 24 A9 A4 6 23 A11 A3 7 22 CS2/OE A2 8 21 A10 Pin name Signal 20 CS1 A0~A14 CS1/CS2 Address input A1 1 I1 2 I2 3 I3 4 I4 5 I5 6 I6 7 8 I7 GND 9 A0 10 19 IO8 IO1 11 18 IO7 IO2 12 17 IO6 IO3 13 16 IO5 VSS 14 15 IO4 WE OE I/O1~I/O8
UX-510UA FO-1470U IC9: VHiSCE114//-1 (SCE114) GPIO[31] GPIO[32] GPIO[33] GPIO[34] GPIO[35] GPIO[36] VDD GPIO[0]/SR4IN GPO[31]/SR3OUT GPIO[37]/IRQ15N IARESET IACLK/DSPCSN IA1CLK SR3IN/DSPIRQN SR4OUT SR1IO SA1CLK VSSPLL TSTCLK DEBUGN RDN WRN SYNC/GPO[20] ROMCSN CS1N/GPO[21] VSS SXIN SXOUT VDD PM[3]/GPO[3] PM[2]/GPO[2] PM[1]/GPO[1] PM[0]/GPO[0] SM[3]/GPO[7] SM[2]/GPO[6] SM[1]/GPO[5] SM[0]/GPO[4] REGDMA/GPO[18] WAITN/GPO[19] VDDPLL D[7] D[6] D[5] D[4] 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147
UX-510UA FO-1470U [3] Changing the record paper size How to change the A4 size and letter size of the record papers 1) It becomes the record paper of the A4 size by installing A4 paper guide (PGiDM2493XHSA) which shows in the drawing. Remove A4 guide when you use the record paper of the letter size. A4 paper guide PGiDM2493XHSA Screw XEBSD30P10000 RP hopper 2) Set soft switch SW-L2 No.1 and the initialization of SW-L2 No.2 as follows. SW NO. DATA NO.
UX-510UA FO-1470U PARTS GUIDE UX-510A MODEL FO-1470 SELECTION CODE U DESTINATION U.S.A. CONTENTS 1 Cabinet, etc.
UX-510UA FO-1470U [1] Cabinet, etc.
UX-510UA FO-1470U PARTS CODE NO. PRICE RANK NEW MARK PART RANK BH AT AK AK BU BC AK AC AD AC AP AM AP AG AA AE AZ AL AC AC AD AP BF AP AG AB AD AE AC AE AC AD AX AD AP AF AD AD AD AC AB AC AC AE AK AD AD AH AN AK AD AE AK AC AC AC AE AS AP AB AC AD AD AK AC AQ AG AC AD AC AD AD AF AM AE AB AH AL AK AE N N N N N N E E C C E E C C C C C C C C C B D D C C C B E C C C C C C C C D C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C C D D C C DESCRIPTION [1] Cabinet,etc.
UX-510UA FO-1470U NO. PARTS CODE PRICE RANK NEW MARK PART RANK AE AC AB AE AA AC AC AE AP AD AD AD AC AG AC AA AC AA AA AB AA AA AB AB N C C C C C C DESCRIPTION [1] Cabinet,etc.
UX-510UA FO-1470U [2] Upper cabinet 901 7 3 4 5 6 1 11 B1 9 2 8 B1 B1 PARTS CODE NO.
UX-510UA FO-1470U [3] Document guide upper 4 12 4 2 14 7 1 17 5 17 6 8 15 13 8 10 3 11 16 NO.
UX-510UA FO-1470U [4] Optical unit 12 5 10 3 14 12 B8 6 1 13 901 15 15 4 2 9 17 7 8 17 NO.
UX-510UA FO-1470U [5] Drive unit B2 B2 14 5 4 15 16 3 12 13 9 8 7 10 2 6 1 11 11 9 17 Cut after insert must be touch to the bottom. PARTS CODE NO.
UX-510UA FO-1470U [6] Head unit 1 W1 6 4 16 B6 9 5 3 15 17 5 16 B6 7 13 10 B2 12 17 14 11 8 2 (100mm) PARTS CODE NO.
UX-510UA FO-1470U [7] Packing material & Accessories 4 7 TAPE TAPE 1 TAPE 5 3 6 12 2 Turn Over 13 15 10 16 13 13 9 17 14 TAPE 18 11 19 PARTS CODE NO.
UX-510UA FO-1470U NO.
UX-510UA FO-1470U NO.
UX-510UA FO-1470U NO.
UX-510UA FO-1470U NO. PARTS CODE PRICE RANK NEW MARK PART RANK AA N C Jumper wire BU N E Control PWB unit(Within ROM) B C C C C C C C C C C C C C C C C C C C C C C C C C C C C B C C C B B B B B C C C C C C C B B B B C C C C C C C C C C C C C C C C C C C C C C Varistor(RA-391P-V6-2) Cable Capacitor(50WV 22µF) Capacitor(50WV 22µF) Capacitor(50WV 4.7µF) Capacitor(50WV 22µF) Capacitor(50WV 22µF) Capacitor(250WV 0.
UX-510UA FO-1470U NO. PARTS CODE PRICE RANK NEW MARK PART RANK AA AA AA AA AA AA AA AA AA AA AG AG AG AC AC AA AA AB AB N C C C C C C C C C C C C B B B B B B B Resistor(1/16W 39KΩ ±5%) Resistor(1/16W 0Ω ±5%) Resistor(1/16W 1KΩ ±5%) Resistor(1/16W 10KΩ ±5%) Resistor(1/16W 3.
UX-510UA FO-1470U PARTS CODE NO. PRICE RANK NEW MARK PART RANK AD AD AD AC AD N B B B B B Varistor(S07K150GA) Variable resistor(EVN CYA A03 B13(102)) Zener diode(RD4.3SB2-T1) Zener diode(RD30FB3-T7) Zener diode(RD6.2SB-T1) BF N E Power supply PWB unit AB AA AH AX AB AA AA C C C B B C C Capacitor(50WV 22µF) Capacitor(50WV 0.022µF) Cable IC(TCD1208AP) Transistor(2SC1815GR) Resistor(1/4W 2.
UX-510UA FO-1470U Index PARTS CODE [C] CCNW-391AXH01 CGERH2314AX51 CGERH2363AX01 CLEVP2254AX01 CLEVP2255AX01 CLEVP2256AX01 CROLR2362AX01 CROLR2363XH02 [D] DCEKC281PXHZZ ″ DCEKD475AAX05 ″ DCEKL266CXH01 ″ DCEKP264CXH01 ″ DCEKP264CXH02 ″ DCEKP351BXH02 ″ DCYOD475AXH03 DUNTK464BXHFW DUNTK464BXHOG [G] GCABA2289XHYA GCABA2289XHYB GCABB2290XHAA GCABB2290XHAB GCABC2291XHYA GCABC2291XHYB GCOVA2375XHYZ GCOVA2376XHYA GCOVA2376XHYB GCOVA2378AXZZ GLEGG2063AXZZ [H] HPNLH2405XHSA HPNLH2405XHSB [J] JBTN-2202AXSC JBTN-2202X
UX-510UA FO-1470U PRICE NEW PART RANK MARK RANK PARTS CODE No.
UX-510UA FO-1470U PARTS CODE No.
UX-510UA FO-1470U COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
