4192121-Rev.A-DK 6 5 9 11 16 15 13 7 8 18 1 - INCLUDES ITEMS 3 - 16 17 19 3 10 4 Parts & Maintenance Manual Reservedels- og vedligeholdelsesmanual R-311™ Rotary Mower with folding ROPS R-311™-rotorplæneklipper med sammenfoldelig ROPSstyrtbøjle 69166 – Kubota® V2203-M 69167 – Kubota® V2203-M EC WARNING If incorrectly used, this machine can cause severe injury.
FOREWORD This manual contains adjustment, maintenance, troubleshooting instructions, and parts list for your new Jacobsen machine. This manual should be stored with the equipment for reference during operation. ® CHARLOTTE, NC MADE IN U.S.A. Before you operate your machine, you and each operator you employ should read the manual carefully in its entirety. By following the safety, operating, and maintenance instructions, you will prolong the life of your equipment and maintain its maximum efficiency.
Table of Contents 1 1.1 1.2 2 2.1 2.2 2.3 2.4 2.5 2.6 3 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.17 3.18 Safety Operating Safety .................................................................... 4 Important Safety Notes ..........................................................5 Specifications Product Identification ............................................................. 6 Engine ....................................................................................
1 SAFETY 1.1 1 OPERATING SAFETY ______________________________________________________________________ SAFETY ! WARNING EQUIPMENT OPERATED IMPROPERLY OR BY UNTRAINED PERSONNEL CAN BE DANGEROUS. Familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive instruction from someone familiar with the equipment before being allowed to operate the machine. 1.
SAFETY 1 1.2 IMPORTANT SAFETY NOTES ________________________________________________________________ This safety alert symbol is used to alert you to potential hazards. DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
2 SPECIFICATIONS 2.1 2 PRODUCT IDENTIFICATION ________________________________________________________________ SPECIFICATIONS 69166...............................R-311 with folding ROPS. 69167...............................R-311 with folding ROPS EC. Serial Number .................An identification plate, like the one shown, listing the serial number, is attached to the frame of the mower near the center lift arm mount.
SPECIFICATIONS 2 2.4 CUTTING UNITS ___________________________________________________________________________ Type......................................... Three Fully Floating Decks Width: Front Deck........................ 64 in. (1625 mm) Wing Decks ...................... 42 in. (1067 mm) 2.5 WEIGHTS AND DIMENSIONS ________________________________________________________________ Dimensions: Inches Length.............................................................................144 Height (ROPS)..
3 ADJUSTMENTS 3.1 3 GENERAL _______________________________________________________________________________ ADJUSTMENTS ! WARNING 2. Replace, do not adjust, worn or damaged components. 3. Long hair, jewelry, or loose fitting clothing may get tangled in moving parts. To prevent injury, lower implements to the ground, disengage all drives, engage parking brake, stop engine, and remove key from ignition switch before making any adjustments or performing maintenance.
ADJUSTMENTS 3 Adjust brakes after replacing or servicing brake assembly, or if pedal travel becomes excessive. 1. When installing new brake pads, burnish pads by driving mower at mowing speed while applying a slight pressure on brake pedal for about 5 seconds. Release and repeat five times before making the final adjustment. 2. Fully loosen adjusting nut (C). 3. By hand, pull cable behind adjusting nut (B) away from pedal until brake pads just contact brake disk.
3 ADJUSTMENTS 3.6 CRUISE CONTROL SWITCH ________________________________________________________________ If the cruise control does not disengage when brake pedal is depressed, cruise control switch must be adjusted. 1. Loosen hardware (F). 2. Adjust switch (G) so contacts are closed with the brake disengaged and open as soon as the brake pedal is pressed. 3. Tighten hardware to secure switch and recheck switch operation. F G Figure 3E 3.
ADJUSTMENTS 3 3.9 HYDRO NEUTRAL _________________________________________________________________________ If the mower “creeps” in either direction, the Neutral position must be adjusted. The mower may tend to “creep” if the hydraulic oil is cold. Operate mower for 15 minutes before determining if adjustment is needed. ! WARNING Carbon monoxide in the exhaust fumes can be fatal when inhaled. Any adjustments or repairs performed while the engine is running must be made with ample ventilation. b. 6.
3 ADJUSTMENTS 3.11 STEERING TOE IN_________________________________________________________________________ “Toe in” should be adjusted from X + 1/16 in. (1.5 mm). 1. Turn wheels to straight ahead position. 2. Loosen tie rod jam nuts (U). 3. Adjust tie rod and retighten jam nuts. 4. After adjusting “Toe in” it may be necessary to re-adjust steering stop bolts. X U U X + 1/16 in. (1.5 mm) Figure 3J 3.12 TURNING RADIUS_________________________________________________________________________ 1.
ADJUSTMENTS 3 3.14 CUTTING HEIGHT__________________________________________________________________________ Level the front mower before setting the cutting height for the first time. Do not remove the cutting units from the mower to change cutting height. Cutting height for decks can be adjusted from 1 to 5-1/2 in. (25-140 mm) in 1/2 in. (13 mm) increments. Actual cutting height may vary somewhat from the heights given depending on turf conditions, tire variances and other factors.
3 ADJUSTMENTS 3.15 LEVELING FRONT MOWER _________________________________________________________________ 1. Before leveling the front deck, the mower tires, and caster wheels must be properly inflated. The cutting height is directly related to the radius of the tire. 2. Set the cutting height of the front mower to 5-1/2 in. (140 mm). 3. Rotate all blades so that one end of the blade (A) is pointing forward. 4. Fully lower front deck.
ADJUSTMENTS 3 3.17 TORQUE SPECIFICATION ___________________________________________________________________ NOTICE All torque values included in these charts are approximate and are for reference only. Use of these torque values is at your sole risk. Jacobsen is not responsible for any loss, claim, or damage arising from the use of these charts. Extreme caution should always be used when using any torque value. Jacobsen uses Grade 5 Plated bolts as standard unless otherwise noted.
4 MAINTENANCE 4.1 4 GENERAL _______________________________________________________________________________ MAINTENANCE ! WARNING Before you clean, adjust, or repair this equipment, disengage all drives, lower implements to the ground, engage parking brake, stop engine, and remove key from ignition switch to prevent injuries. Make sure the mower is parked on a solid and level surface. Never work on a mower that is supported only by the jack. Always use jack stands. 1.
MAINTENANCE 4 4.3 1. SHARPENING BLADES _____________________________________________________________________ Place a wooden block between the blade and mower housing to stop the blade from moving. To remove blade, turn screw holding blade counterclockwise. A Maximum 1/2” (13 mm) ! WARNING The mower blades can develop sharp edges. Use caution whenever servicing and handling. 2. B When dressing or sharpening the blade, do not follow the original pattern of grind as shown in (A).
4 MAINTENANCE 4.4 ENGINE _________________________________________________________________________________ IMPORTANT: A separate Engine Manual, prepared by the engine manufacturer, is supplied with this mower. Read the Engine Manual carefully until you are familiar with the operation and maintenance of the engine. Proper attention to the engine manufacturer’s directions will assure maximum service life of the engine. To order replacement engine manuals contact the engine manufacturer.
MAINTENANCE 4 4.6 AIR FILTER _______________________________________________________________________________ Do not remove the element for inspection or cleaning. Unnecessary removal of the filter increases the risk of injecting dust and other impurities into the engine. 3. Assemble the new element and make sure it seats properly. 4. Reassemble cap making sure it seals completely around the filter housing. Dust evacuator must be facing down.
4 MAINTENANCE 4.9 BATTERY ________________________________________________________________________________ Make absolutely certain the ignition switch is OFF and the key has been removed before servicing the battery. ! CAUTION Always use insulated tools, wear protective glasses or goggles, and protective clothing when working with batteries. You must read and obey all battery manufacturer’s instructions. 1.
MAINTENANCE 4 4.12 HYDRAULIC HOSES________________________________________________________________________ ! WARNING To prevent serious injury from hot, high pressure oil, never use your hands to check for oil leaks, use paper or cardboard. 3. The replacement tube or hoses must be routed in the same path as the existing hose, do not move clamps, brackets, or ties to a new location. 4. Thoroughly inspect all tubes, hoses, and connections every 250 hours.
4 MAINTENANCE 4.14 HYDRAULIC OIL FILTERS __________________________________________________________________ The hydraulic system is protected by two 10 micron filters. ! WARNING Charge filter is under pressure. Remove filter slowly to prevent personal injury. To replace hydraulic oil filter: 1. Remove the old filter. 2. Fill new filter with oil then install new filter. Hand tighten only. 3. Operate engine at idle speed with hydraulic system in neutral for five minutes. 4.
MAINTENANCE 4 4.18 WHEEL MOUNTING PROCEDURE ____________________________________________________________ ! WARNING Make sure the mower is parked on a solid and level surface. Never work on a mower that is supported only by the jack. Always use jack stands. If only the front or rear of the mower is raised, place chocks in front of and behind the wheels that are not raised. 1. Remove dirt, grease, and oil from stud thread. Do not lubricate threads. 2.
4 MAINTENANCE 4.21 RADIATOR AND OIL COOLER_______________________________________________________________ ! WARNING To prevent serious bodily injury from hot coolant or steam blowout, never attempt to remove the radiator cap while the engine is running. Stop the engine and wait until it is cool. Even then, use extreme care when removing the cap. ! CAUTION Do not pour cold water into a hot radiator. Do not operate engine without a proper coolant mixture. Install cap and tighten securely. 1.
MAINTENANCE 4 4.22 STORAGE ________________________________________________________________________________ General 4. If storing indoors, drain fuel from tank. 1. 5. Close fuel shut off valve. Wash the mower thoroughly and lubricate. Repair and paint damaged or exposed metal. 2. Inspect the mower, tighten all hardware, replace worn or damaged components. 3. Drain and refill radiator. 4. Clean the tires thoroughly and store the mower so the load is off the tires.
5 TROUBLESHOOTING 5.1 5 GENERAL _______________________________________________________________________________ TROUBLESHOOTING The troubleshooting chart below lists basic problems that may occur during start-up and operation. For more detailed information regarding the hydraulic and electrical systems contact your area Jacobsen Dealer. Symptoms Possible Causes Engine will not start. Action 1. Parking brake disengaged, traction 1. pedal not in neutral or PTO switch on.
MAINTENANCE & LUBRICATION CHARTS 6 6.1 6 GENERAL ________________________________________________________________________________ MAINTENANCE & LUBRICATION CHARTS ! WARNING Before you clean, adjust, or repair this equipment disengage all drives, lower implements to the ground, engage parking brake, stop engine, and remove key from ignition switch to prevent injuries. 1. 2. Lubricate with grease that meets or exceeds NLGI Grade 2 LB specifications.
6 MAINTENANCE & LUBRICATION CHARTS 6.3 MAINTENANCE CHARTS ___________________________________________________________________ Recommended Service and Lubrication Intervals Every 8-10 Hours Air Filter (Cab) I Air Filter (Engine) I Battery Charge Every 25 Hours Every 100 Hours Every 400 Hours Every 250 Hours Every 500 Hours Every 1000 Hours Yearly See Section R**** 4.6 R I Belts I-A* Brake 4.9 I-A I-A Cooling System R Engine Oil I Engine Oil Filter Front Axle 3.4 R I* I 4.
NOTES 7 7 NOTES 29
8 PARTS LIST 8.1 HOW TO USE THE PARTS CATALOG_________________________________________________________ 8 PARTS LIST Abbreviations Indented Items N/S - Not serviced seperately, can only be obtained by ordering main component or kit. AR -Variable quantity or measurement is required to obtain correct adjustment. Symbols such as l, next to the item number, indicate that a note exists which contain additional information important in ordering that part.
VORWORT Denne manual indeholder instruktioner i justering, vedligeholdelse og fejlfinding samt en reservedelsliste til din nye Jacobsen-maskine. Denne manual skal opbevares sammen med udstyret til reference under brug. ® CHARLOTTE, NC Bevor Sie Ihre Maschine in Betrieb nehmen, sollten Sie und alle für Sie arbeitenden Bediener beide Handbücher sorgfältig durchlesen.
Indhold 1 1.1 1.2 SIKKERHED Driftssikkerhed ....................................................................... 4 Vigtige bemærkninger om sikkerhed .................................... 5 2 2.1 2.2 2.3 2.4 2.5 2.6 SPECIFIKATIONER Produktidentifikation............................................................... 6 Motor ..................................................................................... 6 Plæneklipper .........................................................................
1 SIKKERHED 1.1 1 DRIFTSSIKKERHED _______________________________________________________________________ SIKKERHED ! ADVARSEL UDSTYR, DER BETJENES FORKERT ELLER AF MEDARBEJDERE UDEN UDDANNELSE, KAN VÆRE FARLIGT. Gør dig bekendt med alle betjeningsanordningernes placering og korrekte brug. Uerfarne operatører skal undervises af nogen, der er bekendte med udstyret, før de får lov at betjene maskinen. 1.
SIKKERHED 1 1.2 VIGTIGE BEMÆRKNINGER OM SIKKERHED ___________________________________________________ Dette sikkerhedssymbol bruges til at advare dig om potentielle farer. FARE – Angiver en overhængende fare, som, hvis den ikke afværges, VIL medføre død eller alvorlig legemsbeskadigelse. ADVARSEL – Angiver en potentielt farlig situation, som, hvis den ikke undgås, KAN medføre død eller alvorlig legemsbeskadigelse.
2 SPECIFIKATIONER 2.1 2 PRODUKTIDENTIFIKATION _________________________________________________________________ SPECIFIKATIONER 69166....................................... R-311 med sammenfoldelig ROPSstyrtbøjle. 69167....................................... R-311 med sammenfoldelig ROPSstyrtbøjle EC. Serienummer ........................... Serienummeret findes på en identificeringsplade, som vist, som er fastgjort til traktorens nær den midterste løftearmsmontage.
SPECIFIKATIONER 2 2.4 KLIPPEENHEDER__________________________________________________________________________ Type..............................................Tre fuldt svævende klippeenheder Bredde: Forreste klippeenhed ............1625 mm Vingeklippeenheder ..............1067 mm 2.5 WEIGHTS AND DIMENSIONS ________________________________________________________________ Mål: mm Længde ..............................................................................................3657 Højde (ROPS) .....
3 JUSTERINGER 3.1 3 GENERELT ______________________________________________________________________________ JUSTERINGER ! ADVARSEL For at undgå personskader skal redskaberne sænkes ned på jorden, alle drev udkobles, parkeringsbremsen trækkes, motoren standses, og nøglen fjernes fra tændingslåsen, før der foretages nogen justeringer eller udføres vedligeholdelse. 1. Justeringer og vedligeholdelse skal altid udføres af en uddannet tekniker.
JUSTERINGER 3 Indstil bremserne efter udskiftning eller service på bremseenheden, eller hvis pedalvandringen bliver for stor. 1. Når du installerer nye bremseklodser, skal du polere klodserne ved at køre plæneklipperen med almindelig klippehastighed, mens du sætter en let tryk på bremsepedalen i ca. 5 sekunder. Slip, og gentag fem gange, før du udfører den endelige indstilling. 2. Løsn justeringsmøtrikken (C) helt. 3.
3 JUSTERINGER 3.6 FARTPILOTKONTAKT _____________________________________________________________________ Hvis fartpiloten ikke deaktiveres, når der trykkes på bremsepedalen, skal fartpilotkontakten indstilles. 1. Løsn de mekaniske dele (F). 2. Indstil kontakten (G), så forbindelserne er lukkede, når bremsen er deaktiveret, og åbne, i samme øjeblik der trykkes på bremsen. 3. Spænd de mekaniske dele for at sikre kontakten, og kontroller kontaktens funktion. F G Figur 3E 3.
JUSTERINGER 3 3.9 HYDRO NEUTRAL _________________________________________________________________________ Hvis traktoren "kryber" i den ene eller den anden retning, skal positionen "neutral" justeres. Traktoren har måske en tendens til at "krybe", hvis transmissionsolien er kold. Betjen traktoren i 15 minutter, før du bestemmer, om justering er påkrævet. ! ADVARSEL Kulilte i udstødningsgasser-ne kan være dødelig, når den indåndes.
3 JUSTERINGER 3.11 STYRETØJETS SPIDSNING _________________________________________________________________ Spidsningen skal justeres fra X + 1,5 mm. 1. Drej hjulene, så de vender lige ud. 2. Løsn to kontramøtrikker på forbindelsesstangen (U). 3. Juster forbindelsesstangen, og tilspænd kontra-møtrikkerne igen. 4. Når du har justeret spidsningen, kan det være nødvendigt at genjustere styretøjets stopbolte. X U U X + 1,5 mm Figur 3J 3.
JUSTERINGER 3 3.14 KLIPPEHØJDE ____________________________________________________________________________ Niveller den forreste klippeenhed, før klippehøjden indstilles første gang. Fjern ikke klippeenhederne fra traktoren for at ændre klippehøjden. 2.
3 JUSTERINGER 1. Før den forreste klippeenhed nivelleres, skal traktorens dæk og styrehjul pumpes op. Klippehøjden er direkte relateret til dækkets radius. 2. Indstil den forreste klippeenheds klippehøjde til 140 mm. 3. Drej alle knivene, så den ene ende af kniven (A) vender fremad. 4. Sænk den forreste klippeenhed helt. Mål fra jorden til punktet (A) og fra jorden til punktet (B). Punktet (B) skal være 3 mm højere end punktet (A). 5.
JUSTERINGER 3 3.17 DREJNINGSMOMENTSPECIFIKATION_________________________________________________________ BEMÆRK Alle drejningsmomentværdier i disse skemaer er cirkaværdier og er kun tænkt som reference. Brug af disse drejningsmomentværdier er på eget ansvar. Jacobsen kan ikke drages til ansvar for eventuelle tab, krav eller skader, der er opstået som følge af anvendelsen af disse skemaer. Man skal altid være yderst forsigtig ved brug af drejningsmomentværdier.
4 VEDLIGEHOLDELSE 4.1 4 GENERELT ______________________________________________________________________________ VEDLIGEHOLDELSE ! ADVARSEL Før du renser, justerer eller reparerer dette udstyr: Udkobl alle drev, sænk redskaber ned på jorden, træk parkeringsbremse, stop motor, og fjern nøgle fra tændingslås for at undgå personskader Sørg for, at traktoren er parkeret på en fast og jævn flade. Arbejd aldrig på en traktor, som kun er understøttet af donkraften. Brug altid donkraftstativ. 1.
VEDLIGEHOLDELSE 4 4.3 1. SKÆRPNING AF KNIVE _____________________________________________________________________ Placér en træklods mellem kniven og klippeskærmen for at forhindre, at kniven kan bevæge sig. Fjern kniven ved at dreje den skrue, der holder kniven, mod uret. A Maksimum 13 mm ! ADVARSEL Klippeknivene kan udvikle skarpe kanter. Vær altid forsigtig, når du servicerer eller håndterer dem. 2. B Følg ikke det oprindelige slibemønster som vist på (A), når du afretter eller skærper kniven.
4 VEDLIGEHOLDELSE 4.4 MOTOR _________________________________________________________________________________ VIGTIGT: En separat Motorhåndbog udarbejdet af motorfabrikanten leveres sammen med denne traktor. Læs Motorhåndbogen grundigt, indtil du er fortrolig med betjeningen og vedligeholdelsen af motoren. Korrekt opfyldelse af motorfabrikantens anvisninger vil garantere motorens maksimale levetid. Kontakt motorproducenten for at bestille supplerende motorhåndbøger. 2.
VEDLIGEHOLDELSE 4 4.6 LUFTFILTER ______________________________________________________________________________ Fjern ikke elementet med henblik på inspektion eller rensning. Unødig fjernelse af filteret øger risikoen for indblæsning af støv og andre urenheder i motoren. 3. Monter det nye element, og sørg for, at det sidder korrekt. 4. Sæt dækslet på igen, idet du sikrer dig, at det er helt forseglet rundt om filterhuset. Støvsuger skal vende nedad.
4 VEDLIGEHOLDELSE Brug altid isoleret værktøj, bær beskyttelsesbriller eller sikkerhedsbriller og beskyttelsestøj, når du arbejder med batterier. Du skal læse og følge alle batterifabrikantens instruktioner. Spænd kabler sikkert fast til batteripoler, og påfør poler og kabelender et tyndt lag dielektrisk siliconefedt for at forhindre ætsning. Hold ventilationsdæksler og pol-låg på plads. 1.
VEDLIGEHOLDELSE 4 4.12 HYDRAULISKE SLANGER___________________________________________________________________ ! ADVARSEL Brug aldrig hænderne til at kontrollere olielækager, brug papir eller pap, for at undgå alvorlig personskade fra varm olie under højt tryk. 3. De nye rør eller slanger skal føres ad den samme bane som den eksisterende slange, flyt ikke klemmer, konsoller og bånd til et nyt sted. 4. Efterse grundigt alle rør, slanger og tilslutninger hver 250 timer.
4 VEDLIGEHOLDELSE Det hydrauliske system er beskyttet af to 10-mikronfiltre ! ADVARSEL Ladefilteret er under tryk. Fjern dækslet langsomt for at undgå personskade. Sådan udskiftes hydraulisk oliefilter: 1. Fjern det gamle filter. 2. Fyld det nye filter med olie, og installer dernæst nyt filter. Spænd kun med hånden. 3. Lad motoren køre ved tomgangshastighed med det hydrauliske system på neutral i fem minutter. 4. Kontroller hydraulikoliestanden, og fyld olie på om nødvendigt. 4.
VEDLIGEHOLDELSE 4 ! ADVARSEL Sørg for, at traktoren er parkeret på en fast og jævn flade. Arbejd aldrig på en traktor, der kun er understøttet af donkraften. Brug altid donkraftstativ. Anbring klodser foran og bag ved de hjul, som ikke er hævet, hvis kun traktorens forende eller bagende er hævet. 1. Fjern snavs, fedt og olie fra pindbolten. Smør ikke gevind. 2. Placer hjul på nav, og efterse for at sikre fuld kontakt mellem monteringsoverfladen på hjul og nav eller bremsetromle. 3.
4 VEDLIGEHOLDELSE 4.21 MOTORKØLER & OLIEKØLER ______________________________________________________________ ! ADVARSEL Undgå alvorlig legemsbeskadigelse fra pludseligt udsprøjtende, varm kølevæske eller damp: Forsøg aldrig at fjerne kølerdækslet, mens motoren er i gang. Stands motoren, og vent, til den er afkølet. Vær selv da yderst forsigtig, når du fjerner dækslet. ! FORSIGTIG Hæld ikke koldt vand ind i en varm køler. Betjen ikke motoren uden en korrekt kølevæskeblanding.
VEDLIGEHOLDELSE 4 4.22 OPBEVARING _____________________________________________________________________________ Generelt Klippeenheder 1. Vask traktoren grundigt, og smør den. Reparer og mal beskadiget eller blotlagt metal. 1. Vask klippeenhederne grundigt, reparer derefter og mal alt beskadiget eller blotlagt metal. 2. Efterse traktoren, spænd alle beslag, udskift slidte eller beskadigede komponenter. 2. Smør alle fittings og friktionspunkter. 3. Tøm og genopfyld køler. 4.
5 FEJLFINDING 5.1 5 GENERELT ______________________________________________________________________________ FEJLFINDING Nedenstående fejlfindingsskema nævner grundlæggende problemer, som kan opstå under opstart og betjening. Kontakt den lokale Jacobsen-distributør for at få flere oplysninger om de hydrauliske og elektriske systemer. Symptomer Mulige årsager Motor vil ikke starte. Motor svær at starte eller kører dårligt. Motor standser. Motor overopheder. Batteri bevarer ikke ladning.
VEDLIGEHOLDELSE & SMØRING 6 6.1 6 GENERELT _______________________________________________________________________________ VEDLIGEHOLDELSE & SMØRING ! ADVARSEL Udkobl alle drev, sænk redskaber ned på jorden, træk parkeringsbremse, stands motor, og fjern nøgle fra tændingslås før rengøring, justering eller reparation af dette udstyr for at forhindre. 1. 2. Smør med fedt, som opfylder eller er bedre end NLGI Grad 2 LBspecifikationerne.
6 VEDLIGEHOLDELSE & SMØRING 6.3 VEDLIGEHOLDELSESSKEMAER ____________________________________________________________ Anbefalede eftersyns- og smøringsintervaller Hver 8-10 timer Luftfilter (førerhus) I Luftfilter (motor) I Batteriopladning Hver 25 timer Hver 100 timer Hver 400 timer Hver 250 timer Hver 500 timer Hver 1000 timer Se afsnit R**** 4.6 I-A* Bremse 4.9 I-A I-A Kølesystem R Motorolie I Motoroliefilter Foraksel 3.4 R 4.21 I* I 4.15 R* R 4.
NOTER 7 7 NOTER 29
8 RESERVEDELSKATALOG 8.1 SÅDAN BRUGES RESERVEDELSKATALOGET_________________________________________________ 8 RESERVEDELSKATALOG Forkortelser N/S - Serviceres ikke separat, kan kun skaffes ved at bestille hovedkomponent eller sæt. AR - Variabel mængde eller mål påkrævet for at opnå korrekt justering (som påkrævet). Symboler, såsom l, ved siden af emnenummeret, angiver, at der findes en note, som indeholder yderligere oplysninger, der er vigtige ved bestilling af denne del. Emne l 8.2 Styknr.
PARTS LIST 8 8.3 TABLE OF CONTENTS______________________________________________________________________ 1.1 ............Decals .................................................................................. 2.1 ............Hood and Front Cowling .................................................... 3.1 ............Hood..................................................................................... 4.1 ............Floorboard Platform ........................................................... 5.1 .
R-311 Serial No. 69166 - All 1.1 Decals THIS RADIATOR CONTAINS ANTI-FREEZE PROTECTED TO -26 F (-32 C) Mix equal parts of clean water and a premium quality ethylene glycol based anti-freeze to maintain the boil over, rust and corrosion protection. 4181861 10 19 10 10 30 30 10 J-TT XXXXXX-XX 18 3008521 16 14 PUSH TO LATCH WING ARMS. PULL TO RELEASE Drain and discard coolant yearly. Read manual for additional instructions.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Qty.
R-311 Serial No. All 2.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Qty.
R-311 Serial No. All 3.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Qty.
R-311 Serial No. All 4.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Qty.
R-311 Serial No. All 5.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Qty.
R-311 Serial No. All 6.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Qty. Description 450453 4 452388 4185860 400186 4195881 445795 443110 4185878 N/S 361723 4192160 4181865 4193341 4193344 4185927 4185871 4185872 4185873 4185874 4185875 4185870 4185868 403770 4203220 4 4 4 3 4 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 4 4 Serial Numbers/Notes Locknut, M8-1.25 Center Screw, M8-1.
R-311 Serial No. All 7.
R-311 Item Part No. Qty.
R-311 Serial No. All 8.1 Lift Valve 6 6 3 6 4 5 8 7 7 2 12 7 13 12 9 1 10 11 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Qty.
R-311 Serial No. All 9.1 Throttle 13 9 8 11 7 2 1 7 6 4 5 10 3 12 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Qty.
R-311 Serial No. All 10.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Qty.
R-311 Serial No. All 11.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Qty.
R-311 Serial No. All 12.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Qty.
R-311 Serial No. All 13.
R-311 Item Part No. Qty.
R-311 Serial No. All 14.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Qty.
R-311 Serial No. All 15.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 Qty.
R-311 Serial No. All 16.
R-311 Item Part No. Qty.
R-311 Serial No. All 17.1 Radiator and Oil Cooler 7 28 30 31 6 44 46 47 8 45 45 42 9 2 1 28 29 2 27 30 25 27 3 20 23 54 26 THIS RADIATOR CONTAINS 30 ANTI-FREEZE 31 PROTECTED TO -26 F (-32 C) Mix equal parts of clean water and a premium quality ethylene glycol based anti-freeze to maintain the boil over, rust and corrosion protection. 33 30 Drain and discard coolant yearly. Read manual for additional instructions.
R-311 Item Part No. 1 4193343 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Qty. Description 1 Radiator Shroud 4164381 1 • 400182 452006 446136 503609 555867 363995 4181862 400286 4189541 446142 445806 117076 441630 338979.
R-311 Serial No. All 18.
R-311 Item Part No. Qty.
R-311 Serial No. All 19.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Qty. Description 4163820 2 443118 4197821 132425 365979 446154 453017 362263 363485 453013 365981 446160 400262 446142 443110 400428 4185160 311879 4 1 1 7 11 7 1 1 1 4 4 8 8 8 4 4 4 Serial Numbers/Notes Mount, Rear Engine Nut, 1/2-13 Hex Mount, Left Front Engine Mount, Right Front Engine Screw, M12-1.25 x 25 mm Lockwasher, 1/2 Heavy Flat Washer, 1/2 Screw, M10-1.25 x 25 mm Lockwasher, M10 Flat Washer, 7/16 Screw, M14-1.
R-311 Serial No. All 20.1 Engine Fuel Control 3 2 4 1 Item Part No. 1 2 3 4 Qty. Description 4177920 1 Throttle Cable 400108 453023 444708 1 1 1 Screw, 1/4-20 x 3/4” Hex Head Flat Washer, 1/4 Locknut, 1/4-20 Center Serial Numbers/Notes See 9.
21.1 Muffler 10 11 7 9 3 8 7 7 5 6 2 4 1 12 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 Qty.
R-311 Serial No. All 22.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Qty.
R-311 Serial No. All 23.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Qty.
R-311 Serial No. All 24.1 Hydraulic Tank ! CAUTION Fill fuel tank to 2 inches below filler neck. DO NOT OVERFILL.
R-311 Item H H H H Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 H Qty.
R-311 Serial No. All 25.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Qty. Description 4153880 1 557447 338938 4138342 4138341 557417 557418 400412 446154 2721522 2721523 400262 444762 400274 453011 446142 443110 4135582 400278 452008 4173300 4200220 4200260 4200280 557629 4170780 4197221 400410 443118 400420 4178400 4178401 4135555 400476 4174300 401225 1002475 400258 458103 132380 3001523.
R-311 Serial No. All 26.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 Qty.
R-311 Serial No. All 27.1 Gear Pump Hydraulics 7 Gear Pump 6 8 2 5 2 1 2 3 8 2 8 10 9 10 9 Left Wing Deck Valve Right Wing Deck Valve 5 11 13 12 10 2 2 4 8 Front Deck Valve Item Part No. Qty.
R-311 Serial No. All 28.1 Control Valve Hydraulics Gear Pump 3 6 5 4 3 3 2 2 S 1 T P LD SD DL 2 1 Control Valve T 4W 1 D 7 8 7 4WD Valve Item Part No. 1 2 3 4 5 6 7 8 9 Qty.
R-311 Serial No. All 29.1 Steering Hydraulics 2 Steering Cylinder 1 S T P LD To Control Valve SD Control Valve DL T 4W D 3 T P 5 4 L Steering Valve R To Steering Cylinder Item Part No. 1 2 3 4 5 Qty.
R-311 Serial No. All 30.1 Lift Hydraulics 11 6 Right Wing Cylinder 4 12 Lift Valve 2 3 1 T S Control Valve P LD SD Right Front Cylinder 1 DL D Left Wing Cylinder 7 Back Pressure Valve 13 8 D 11 T 4W 9 F 5 10 B IN OUT Left Front Cylinder Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 340066 123222 339984 132571 132571 132573 4188043 340119 340003 4193301 340078 339979 340088 Qty.
R-311 Serial No. All 31.1 Lift Return Hydraulics 1 Hydraulic Tank 9 11 8 Right Wing Cylinder 10 5 12 6 Front Right Cylinder 7 1 Left Wing Cylinder 6 5 2 1 4 3 Front Left Cylinder Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 Qty. Description 340061 3 Adapter, 90° 1003595 340263 4197560 340215 339961 4193300 132569 132568 132583 351124 366437.
R-311 Serial No. All 32.1 Motor Return Hydraulics 1 3 5 2 1 Hydraulic Tank 12 7 11 13 8 10 4 4 6 9 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 340055 1000770 1000770 359186 1003138 1003138 360566 339960 4192360 132561 365966 324943 3001523.7 Qty.
R-311 Serial No. All 33.1 Charge Hydraulics 9 10 9 2 11 Steering Valve Charge Filter 7 1 3 To Charge Filter 8 Traction Pump T S P T P LD SD L 6 R DL T 4W D 2 Contol Valve 4WD Valve 4 5 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 Qty.
R-311 Serial No. All 34.1 Oil Cooler Hydraulics Oil Cooler 5 4 10 5 Return Filter 9 10 8 3 7 2 Left Wing Deck Valve 1 6 Front Deck Valve Hydraulic Tank Item Part No. 1 2 3 4 5 6 7 8 9 10 Qty.
R-311 Serial No. All Serial No. All 35.1 Return Hydraulics Hydraulic Valve 1 Backpressure Valve 2 10 3 1 5 8 11 4 6 Control Valve T S P LD SD Traction Pump DL T 4W D 7 9 Front Axle Motor 12 13 Right Wing Deck Valve Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Qty.
R-311 36.1 Front Deck Hydraulics 4 6 1 3 11 2 10 7 12 9 8 5 4 4 5 8 9 Item 7 Part No. 1 2 3 4 5 6 7 8 9 10 11 12 Qty.
R-311 Serial No. All Serial No. All 37.1 Left Wing Deck Hydraulics Left Wing Deck Valve 7 10 2 11 13 5 12 Inside Motor 2 Outside Motor 9 1 3 6 2 4 1 8 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Qty.
R-311 38.1 Right Wing Deck Hydraulics 5 6 Outside Motor 2 3 8 10 Right Wing Deck Valve 2 4 11 12 1 7 2 13 Inside Motor 9 1 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Qty.
R-311 Serial No. All 39.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Qty. Description 366607.
R-311 Serial No. All 40.
R-311 Item Part No. Qty. Description 1 2 3 4 5 365962 1 Wire, Solenoid to Glow Plug 163918 365711 443102 4193880 1 2 4 1 Wire, Circuit Breaker to Solenoid Wire, Starter to Circuit Breaker Nut, 1/4-20 Hex Relay SPDT 6 365963 6 Relay, SPST 7 8 9 10 11 12 13 14 15 16 17 18 19 20 403908 3003036 446136 443808 131905 403910 446118 444310 444312 403759 366308.
R-311 Serial No. All 41.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Qty. Description 4167640 3 Cable Tie, Fir Tree 362263 365980 446154 446130 443102 453023 361064 400120 2720726 453011 446148 473144 473137 345671 400190 446136 443106 1002397 452006 1 1 1 1 1 1 1 1 1 1 1 2 4 2 1 1 1 1 1 Screw, M10-1.25 x 25 mm Screw, M12-1.
98 Panel Lights 1 6 Horn Cruise Magnet Fuel Pump 4WD Valve Charge Filter Left Wing Limit Switch Ground Left Wing Limit Relay Return Filter Air Cleaner Oil Tank Glow Plug Solenoid Speed Sensor 10 Differential Lock Switch Hydraulic Temperature Switch Front Limit Switch Ground 13 Brake Switch Reverse Switch Cab Connector Fuel Solenoid Tail Light Temperature Sender Temperature Switch Alternator 16 Headlights Control Valve Seat Switch Parking Brake Ground Diodes Horn/Test Switch
R-311 Item Part No. Qty.
R-311 Serial No. All 43.
R-311 Item > > Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 19 19 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Qty. Description 2720206 1 342033 2720207 342033 4184641 346091 446136 400184 366045 359549 460052 4138505 4137138 453023 471221 452006 400280 453011 366473 366610 366611 366612 366613 443106 402132 446118 446142 443110 3001079 5000183 5000184 3001078 364694 400188 366437.
R-311 Serial No. All 44.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 Qty. Description 2720295 1 2720298 2720294 2720298 2248004 64251-001 446136 400184 361723 446142 443110 366506 366517 362824 503553 471216 400650 364248 400272 444762 4138515 4138589 366483 4107220 400262 366437.
R-311 Serial No. All 45.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Qty.
R-311 Serial No. All 46.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Qty.
R-311 Serial No. All 47.1 Front Deck A "X" 35 37 38 36 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 16 B "X" 0 1 2 3 4 0 1 2 3 4 A A A A A B B B B B 3.0 4.0 5.0 1.5 1.0 2.5 3.5 3.0 4.5 5.0 2.5 4.5 5.5 5/7 8 / 10 5 40 36 2.0 3 15 17 2 1.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Qty.
R-311 Serial No. All 48.1 Wing Deck Left Wing Deck Shown (Right Opposite) 37 38 33 36 34 35 38 13 39 16 40 1/2 22 20 38 8 17 21 37 5 15 36 40 38 13 39 29 30 28 41 8 / 10 5/7 3 19 Left Wing Deck 31 32 24 5/7 15 8 / 10 16 Right Wing Deck 23 17 25 4 3 9 18 16 16 15 A "X" 27 26 15 6 11 11 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 B "X" 0 1 2 3 4 0 1 2 3 4 A A A A A B B B B B 1.0 2.0 3.0 4.0 5.0 4 7 13 14 12 14 13 10 12 3 110 1.5 2.5 1.0 3.5 3.0 4.5 5.
R-311 Item > Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 Qty.
R-311 Serial No. All 49.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Qty.
R-311 Serial No. All 50.1 Deck Bumper 7 4 2 6 1 3 7 4 5 Item Part No. 1 2 3 4 5 6 7 Qty.
R-311 Serial No. All 51.1 Deck Valve Part Number 4135582 2 3 1 4 / 5/ 6 Item Part No. 1 2 3 4 5 6 Qty. Description 5002911 1 Relief Valve 5003579 5002912 5003554 3010199 339897 5002913 5003579 4134530 2811269 1 1 1 1 1 1 1 1 1 • Seal Kit Relief Valve • Seal Kit Plug, SAE #6 • O-Ring Solenoid Valve • Seal Kit Coil, 12 Volt DC Nut, coil w/o-Rings Serial Numbers/Notes REFERENCE K10, K11, K12, See 60.
R-311 Serial No. All 52.
R-311 Item > l l Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 l Qty.
R-311 Serial No. All 53.1 Control Valve Part Number 4174300 Viewed from Top P ST LD 2 L 1 SD SW 3 CD DL T 4WD F 5 6 4 Viewed from Rear Item Part No. 1 2 3 4 5 6 7 7 Viewed from Right Qty. Description 5003510 1 Relief Valve, 200 psi 5003579 556845 5003579 3010199 4199500 5003578 4199520 4199521 4134532 2811253 1 1 1 1 1 1 1 1 1 1 • Seal Kit Flow Control Valve, 4.
R-311 Serial No. All 54.1 4WD Valve Part Number 4135555 3, 5 4 2 R2 BD 1 B A L2 AD 4WD Viewed from Right Item Part No. 1 2 3 4 5 C L1 R1 Viewed from Left Qty. Viewed from Top Description 556897 1 Spool Valve 5003581 558038 5003581 556847 5003578 4134532 2811253 1 1 1 1 1 1 1 • Seal Kit Check Valve • Seal Kit Solenoid Valve, 4WD Reverse • Seal Kit, Solenoid Valve Coil Nut, Coil Viewed from Bottom Serial Numbers/Notes REFERENCE K16, See 60.
R-311 Serial No. All 55.
R-311 Item l l l l l l l Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Qty.
R-311 Serial No. All Serial No. All 56.1 Rear Wheel Motor Part Number 4178560 2 5 6 2 8 1 3 7 11 9 4 2 10 Item l l t t l l l l t Part No. 1 2 3 4 5 6 7 8 9 10 11 Qty. Description N/S 1 Seal Exclusion N/S N/S N/S 5003384 554780 554779 N/S N/S N/S 556450 4 1 1 1 1 1 1 1 1 4 Seal, 3” I.D.
R-311 57.1 ROPS 2 10 7 8 14 6 13 5 14 9 10 12 11 12 13 8 8 13 7 5 7 3 9 7 11 17 16 8 1 17 16 15 13 6 15 15 17 4 16 15 15 16 17 16 17 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Qty.
R-311 Serial No. All 58.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Qty.
R-311 Serial No. All 59.
R-311 Item Part No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 Qty.
R-311 Serial No. All 60.
R-311 Og/Bu Wh Og/Bu Bk L12 2-D Bk Tn/Rd L11 Tn/Rd Ye Gy Gy 1-N Og/Bu 4-2 4-5 Tn/Rd 4-7 Wh Bk Bk L13 4-6 SW20 SW18 Gn/Wh I + Ye - G Bk Ye I S B Pk/Bu I 3-6 Pu/Wh Pu/Wh Wh/Bk Bk Tn 2-W SW12 Og D5 Gn/Wh L5 Wh/Bk Gn/Wh 1-P Tn G Bk Pu/Wh L4 U7 S D4 Tn 3-2 3-1 S Pk/Bu LG Bk SW1 I Og G Bk Off - None On - B+I+A; X+Y Y Start - B+I+S Bn/Rd 3-5 Pk/Bu SW11 U6 X Bn/Rd Bk 2-R Og Bk A 2-G Wh/Bk Bu/Wh 3-3 3-4 Bn/Rd Bu/Wh L3 Og SW5 Ye D3
R-311 Item B1 CB1 CB2 CB3 CB4 CB5 CB6 CB7 CB8 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 F1 K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 K12 K13 K14 K15 K16 L1 L2 L3 L4 L5 L6 L7 L8 130 Reference Illustration Part Number See 4.1 See 7.1 See 7.1 See 7.1 See 7.1 See 7.1 See 18.1 See 18.1 See 7.1 Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown Not Shown See 42.1 See 40.1 See 40.1 See 40.1 See 40.1 See 40.1 See 40.1 See 40.1 See 40.1 See 40.1 See 51.1 See 51.1 See 51.1 See 18.1 See 53.
R-311 Item Reference Illustration L9 L10 L11 L12 L13 M1 M2 R1 SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8 SW9 SW10 SW11 SW12 SW13 SW14 SW15 SW16 SW17 SW18 SW19 SW20 SW21 SW22 SW23 U1 U2 U3 U4 U5 U6 U7 U8 U9 U10 Not Shown Not Shown Optional Optional Optional See 18.1 Optional See 18.1 See 7.1 See 12.1 See 6.1 See 7.1 See 7.1 See 7.1 See 7.1 See 45.1 See 45.1 See 43.1 See 16.1 See 23.1 See 24.1 See 23.1 See 25.1 See 18.1 See 18.1 Optional See 7.1 See 15.1 See 12.1 See 7.1 See 10.1 See 18.1 See 15.1 See 42.1 See 7.
R-311 Serial No. All 61.1 Hydraulic Schematic Traction Pump Four Section Gear Pump A 2.48 3 in 2800 RPM CCW Rotation 3500 PSI 1.04 3 in 1.04 3 in 1.04 3 in 0.77 3 in A 5.04 3 in 3500 PSI Front Axle Motor B B D1 D3 C D Outside Right Wing Motor 100 PSI 1.04 3 in .0669 E Right Wing Deck Valve A F P D D 1.04 3 in .0669 B 630 PSI 3000 PSI T 25 psi Switch 10 Micron 25 psi Crack Bypass Inside Right Wing Motor Inside Left Wing Motor Charge Filter 100 PSI 1.
R-311 4WD A A AD AB 4WD Valve B C B L2 R2 R1 L1 Right Motor C D 11.9 3 in E F 11.9 3 in Steering Valve Left Motor P 1500 PSI R 6.1 3 in Control Valve SD P Steering Cylinder DL SW CD F 200 PSI T T L ST 4WD LD G L IN OUT 1500 PSI Backpressure Valve 50 PSI 300 PSI Lift Valve 0.0595 in. H I J Right Wing Cylinder B A 0.0595 in. Front Left Cylinder 300 PSI D C 300 PSI F 0.0595 in. Front Right Cylinder E 0.0595 in.
HR-5111 Serial No. All 62.
HR-5111 Adapter Part Number.
Fluids and Compounds Hydraulic Fluid* 5001405 5001404 2500548 2500546 503409 503407 Two 2-1/2 Gallon Container of ISO VG68 Oil One 5 Gallon Pail of ISO VG68 Oil Two 2-1/2 Gallon Container of 10W30 Oil One 5 Gallon Pail of 10W30 Oil Two 2-1/2 Gallon Container of ATF Fluid One 5 Gallon Pail of ATF Fluid 2-Cycle Oil 554600 Twenty Four 16 Ounce Plastic Container 554599 Twenty Four 8 Ounce Plastic Container Grease 5000067 One 5 Gallon Pail OO-Grease 5000068 Twenty Four 8 Ounce Tube OO-Grease Paint 5003
INDEX 1000050 . ..............................69 1000588 . ..............................45 1000649 . .......................49, 53 1000700 . ..............................79 1000770 . ..............................85 1000843 . ..............................79 1001226 . ..............................69 1001251 . ..............................69 1001311 . ..............................71 1001802 . ..............................46 1001885 . ...................109, 111 1001963 . ..............................
INDEX 340481 .. ..............................71 340525 .. ............................105 340783 .. ..............................51 340795 .. ..............................37 342033 .. ............................101 344996 .. ..............................63 345666 .. ....................... 73, 93 345671 .. ..............................97 346091 .. ................... 101, 103 346294 .. ............................107 346913 .. ............................107 350685 .. ..............................
INDEX 4172742 . ..............................53 4172743 . ..............................53 4172900 . ..............................53 4172901 . ..............................55 4172944 . ..............................47 4173220 . ..............................88 4173221 . ..............................88 4173300 . ..............................77 4173562 . ............................125 4173563 . ............................125 4173566 . ............................125 4173567 . ..........................
INDEX 5000938 . ..............................65 5001072 . ............................111 5001073 . ............................111 5001599 . ............................117 5001603 . ............................117 5001612 . ............................117 5001613 . ............................117 5001614 . ............................117 5001615 . ............................117 5001616 . ............................117 5002101 . ..............................45 5002102 . ..............................
World Class Quality, Performance and Support Equipment from Jacobsen is built to exacting standards ensured by ISO 9001 and ISO 14001 registration at all our manufacturing locations. A worldwide dealer network and factory trained technicians backed by Genuine Jacobsen Parts provide reliable, high-quality product support.
