DV-L70S DV-L70BL DV-L70W SERVICE MANUAL SY9S7DV-L70S/ SERVICE MANUAL PORTABLE DVD VIDEO PLAYER MODELS DV-L70S DV-L70BL DV-L70W PORTABLE DVD VIDEO PLAYER In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified be used. CONTENTS MODELS DV-L70S/BL/W Page 1. IMPORTANT SAFEGUARDS AND PRECAUTIONS ......................................................................... 2 2.
1.
DV-L70S DV-L70BL DV-L70W åCAUTION BEFORE BATTERY DESTROY Ë NICKEL-CADMIUM BATTERY The following program is available in the United States. Please consult local environmental authorities concerning the availability of this or other programs in your area. The RBRCTM Seal SHARP participates in the RBRCTM* Nickel-Cadmium Battery Recycling Program in the United States.
DV-L70S DV-L70BL DV-L70W 2. FEATURES 7" LCD Screen and Stereo Speakers • A big 7" LCD screen and built-in stereo speakers provide exciting DVD viewing, even without connecting to a TV. • Dolby Virtual provides high-quality surround sound. 2-WAY Power Supply (Battery pack is sold separately.) • A 2-way power supply allows operation using the supplied AC adapter for indoor play, or the battery pack sold separately for outdoor play.
DV-L70S DV-L70BL DV-L70W Audio Signals: Frequency Characteristics: Linear PCM DVD: 4Hz to 22kHz (48kHz sampling)/ 4Hz to 44kHz (96kHz sampling) CD: 4Hz to 20kHz (EIAJ) (Audio MPEG Version 2.0) S/N Ratio: CD: 95 dB 1kHz (EIAJ) Dynamic Range: Linear PCM DVD: 94dB (EIAJ) CD: 94dB (EIAJ) Total Harmonic Distortion Ratio: 0.006% maximum (EIAJ) Power Requirements: AC Adapter: 9V DC Power Consumption: Main Power On: 11W average (15.5W maximum) (AC Adapter) Standby: 0.
DV-L70S DV-L70BL DV-L70W 4. PART NAMES For details on the use of each control.
DV-L70S DV-L70BL DV-L70W 5. DISASSEMBLY METHOD 1 5-1. DISASSEMBLY METHOD 1. Remove the nine screws 1. 2. Loosen the two screws 2. 3. After opening the LCD unit, remove the hinge claw of cabinet A to detach it from cabinet B. Note: The power SW button is also removed. Be careful not to forget it when assembling the unit. 4. Remove the FFC A from the main PWB. 2 A Power SW Button 5. Remove the screws 3.
DV-L70S DV-L70BL DV-L70W 6. ADJUSTMENT METHOD 6-1. HARNESS LIST FOR SERVICE PARTS Parts Code Price Code QCNW-8145GEZZ AQ QCNW-8146GEZZ QCNW-8147GEZZ Remarks Parts Code Price Code Remarks P.U.
DV-L70S DV-L70BL DV-L70W 6-3. CHECK ITEMS OF LCD PWB SIDE 1. Power supply voltage check Adjustment Point Input Signal/Setting Adjustment Method Put voltmeters in 4PIN (GND), 5PIN (-16V) and 7PIN (13V) of TP1191. Check in the DVD mode. Check that each voltage indicates -16±1V and 13±0.5V respectively. 2. Free run check Adjustment Point Input Signal/Setting Adjustment Method Check the panel visually by connecting to the checker.
DV-L70S DV-L70BL DV-L70W 1. DAC adjustment (1) TV1 adjustment Adjustment VR GAM0 Initial value "44" adjustment is unnecessary. Adjustment VR Adjustment Point Input Signal/Setting SBRI ———— It is set in "56". Adjustment VR Adjustment Point Input Signal/Setting Adjustment Method GPOS Connect the oscilloscope to COM output (6PIN of TP1901) and GND. Black-and-white 10STEP Adjust the common amplitude to 8.0±0.1Vp-p. 8.0±0.
DV-L70S DV-L70BL DV-L70W Adjustment VR Adjustment Point Input Signal/Setting Adjustment Method STIN Connect the oscilloscope to 5PIN (VB) and GND of TP1901. 100% color bar It is adjusted so that shakes of the waveform of the blue signal of the color bar may become the smallest.
DV-L70S DV-L70BL DV-L70W 6-5. CHECK AND READJUSTMENT 1. Free run check Adjustment VR Adjustment Point Input Signal/Setting Check and Readjustment R1104 Visual observation External input Check that the horizontal movement of OSD position is 1 mm or less when inputting a signal in the external input mode with no signal input. If it is more than 1 mm, adjust it so as to get 1 mm or less. Input 2.
DV-L70S DV-L70BL DV-L70W 7. TEST MODE When a power source is put with pushing a key. Adjustment Mode ROM renewal mode A power source is put with pushing and . It is put with pushing a playback key and a still key. A power source is put. When there is a disc Error rate display mode (There are a DVD and CD mode of it, and a disc is put, and a key manipulates.) When there is Test mode (Version display mode, color bar pattern display mode, mecha test mode.
DV-L70S DV-L70BL DV-L70W From (1) Mecah test mode display 30000000 00000000 When it failed in servo initialization. It is returned to the test mode initial image plane by pushing "the playback" of the remote controller and a "stop" key at the same time. Mecah test mode display 3000E000 EEEEEEEE
DV-L70S DV-L70BL DV-L70W From (2) The "playback" key of the remote controller is pushed. Servo version display F1000001 99071400 The "playback" key of the remote controller is pushed. Focus offset value display F1000002 ∗∗∗∗∗∗∗∗ The "playback" key of the remote controller is pushed. Track offset value display F1000003 ∗∗∗∗∗∗∗∗ The "playback" key of the remote controller is pushed. 0 layer focus balance value display F1000004 ∗∗∗∗∗∗∗∗ The "playback" key of the remote controller is pushed.
Check the switch SW9001. Check the FET-TrQ9006. Are the connector CN9002 and FFC wire normal? NO NO NO YES NO Check the DC jack and fuse F9001. NO Is key switch contact and installation state? YES Is the control voltage normally into the pins 95 and 96 of IC504? (95pin-key1, 96pin-key2) YES Check the peripheral circuit or replace IC504. NO Key manipulation on the DVD function side doesn't function. FLOW CHART NO.4 Replace key switch. Check the IC9001 and FET-TrQ9002.
NO NO 17 Is the focus control drive voltage being applied to the pins 4 and 2 of CN301? YES Check the connection of optical pickup cable. If it is normal, replace the pickup. YES Is the focus control voltage being output from the pins 24 and 25 of IC702? NO NO Is the FE signal being input to the pin 38 of IC707? NO (Check item for the symptom) YES Is the focus control signal being output to the pin NO 43 of IC707? YES The disc is not recognized.
NO IC1801 5pin C-SIG. 18 NO NO Is TFT LCD CONTROL PROCESSOR (IC1101) normal? YES LCD panel peripheral circuit and the existence of the failure place of the appearance are confirmed. Is the COM2 bias level of the LCD panel normal? YES YES YES NO Do 19 of IC1801, 21, 24 pin (VR, VG, VB) output appear? YES Is a power source being supplied to the LCD panel NO normally? VGH(+13V), VSS(-16V), VCC(-10.9V), VSH(4.8V), VGL(-10V) NO NO NO A disk is set on the tray, and played back.
Is a signal being inputted to the following, each output terminal of the integrated circuit? IC6203 12pin AUDIO(L-CH)-SIG. IC6202 12pin AUDIO(R-CH)-SIG. YES Is a signal being inputted to the following, each output terminal of the integrated circuit? IC6002 2pin AUDIO(L-CH)-SIG. IC6002 6pin AUDIO(R-CH)-SIG. YES Does a signal come out in the following, each output terminal of the integrated circuit? IC6203 2, 5pin AUDIO(L-CH)-SIG. IC6202 4pin AUDIO(R-CH)-SIG. YES Set the disc on the disc tray.
DV-L70S DV-L70BL DV-L70W 9.
DV-L70S DV-L70BL DV-L70W 9-2. IC303 IX1517GE Pin No.
DV-L70S DV-L70BL DV-L70W Pin No. 53 54 55 56 57 58 59 60 61 62 63 64 Terminal name P1CI P1BI P1AI GNDR LDP2 I/O I I I – I Operation function C input (DVD) B input (DVD) A input (DVD) GND terminal (RF) APC polarity 2 P2AI P2BI P2CI P2DI GNDS P2FP P2FN I I I I – I I A input (CD) B input (CD) C input (CD) D input (CD) GND terminal (Servo) FE+input (CD) FE–input (CD) Terminal DC Voltage(TYP.) Remarks VrA VrA VrA – – Positive polarity when this terminal is connected to Vcc.
DV-L70S DV-L70BL DV-L70W 9-4. IC402 IX1474GE DEM/ECC (DVD) Pin No. 1 Terminal name DPCK1 I/O I Operation function Signal processing reference clock input. 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 DVDD3 SVCK1 SVCK0 DVSS DVDD2 N.C.
DV-L70S DV-L70BL DV-L70W Pin No.
DV-L70S DV-L70BL DV-L70W FLASH Input A0-A12 Input A13-A17 Input 25, 24~18, 8~4 3~15, 48, 17 29, 31, 33, 35, 38, 40, 42, 44 30, 32, 34, 36, 39, 41, 43, 45 DQ0-DQ7 Input/Output DQ8-DQ15 Input/Output 26 CE# Input 12 RP# Input 28 OE# Input 11 WE# Input 15 RY/BY# Output 47 BYTE# Input 13 37 27, 46 9, 10, 14, 16 Vpp Vcc GND NC • Block Diagram DQ8-15 DQ0-7 Output Buffer Output Buffer Input Buffer Input Buffer I/O Logic BYTE# OUTPUT MULTIPLEXER DATA ID Register QUEUE REGIS
DV-L70S DV-L70BL DV-L70W PD7/D15 PD6/D14 PD5/D13 PD4/D12 PD3/D11 PD2/D10 PD1/D9 PD0/D8 PE7/D7 PE6/D6 PE5/D5 PE4/D4 PE3/D3 PE2/D2 PE1/D1 PE0/D0 SYSCON Vcc Vcc Vcc Vcc Vcc Vss Vss Vss Vss Vss Vss Vss Vss Clock oscillator Port G A/D converter PPG P35/SCK1 P34/SCK0 P33/RxD1 P32/RxD0 P31/TxD1 P30/TxD0 P50 P51 P52 P53/ADTRG P47/AN7/DA1 P46/AN6/DA0 P45/AN5 P44/AN4 P43/AN3 P42/AN2 P41/AN1 P40/AN0 Vref AVcc AVss Port 4 P10/PO8/TIOCA0/DACK0 P11/PO9/TIOCB0/DACK1 P12/PO10/TIOCC0/TCLKA P13/PO11/TIOCD0/TCLKB P14
DV-L70S DV-L70BL DV-L70W 9-8.
DV-L70S DV-L70BL DV-L70W Pin1~15 ........ There is a possibility of simultaneous change. Pin18~47 ..... There is a possibility of simultaneous change.(Static signal) Pin50~57 ..... There is almost no possibility of simultaneous change. Pin63 ............ Not used Operating frequency: Approx. 10 MHz Operating frequency: Approx. 1 MHz Operating frequency: Approx.
DV-L70S DV-L70BL DV-L70W 9-9. IC601 IX1608GE Pin No. Pin name Type I/O Function Host interface, CD-DSP interface, subcode interface (32-pin) Reset input (active low). When deassert is applied in the asserted state, the 141 RESET# I I initializing process of MD36710X is started. Stand-by input (active low). When it is asserted together with RESET#, all output pins and bidirectional pins are floated to separate MD36710X electrically from the 130 STNDBY# I I peripherals.
DV-L70S DV-L70BL DV-L70W Pin No. Pin name GPI/O signal (4-pin) Type I/O 122,123 3-S I/O I O I O I I GPAI/O [1:0] 2 GPSI 159 GPSO PLL signal (6-pin) 129 GCLK 126 GCLK1 I I 128 XO O O 136 PLLCA I I 137,135 PLLCFG [1:0] Function General purpose bidirectional pin for monitor and control with ADP microcode. After resetting, this pin is defined as the input. If ADP command is used, setting is possible. General purpose input for monitor with DVP microcode.
DV-L70S DV-L70BL DV-L70W Pin No.
DV-L70S DV-L70BL DV-L70W 9-10. IC602 IX0750TA Terminal 35 18 34 Terminal Name Name CLK System Clock CS Chip Select Input Function Active on the positive going edge to sample all inputs. Disables or enables device operation by masking or enabling all inputs except CLK. CKE and L(U)DQM Masks system clock to freeze operation from the next clock cycle. CKE should be enabled at least one cycle prior to new command. Disable input buffers for power down in stanby.
DV-L70S DV-L70BL DV-L70W 9-11. IC701 AN8473NS-1 Pin No.
DV-L70S DV-L70BL DV-L70W 9-12. IC702 BA5933FP-1 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 Terminal name STBY OUT+ OUTGND VCC MUTE GND REG_OUT REG_B BIAS IN1' IN1 Operation function Stand-by mode selector switch CH1 positive output terminal CH1 negative output terminal GND VCC Mute terminal Substrate GND Constant voltage output (collector of external Tr) Connected to the base of external Tr Bias input terminal CH1 gain adjustment input terminal CH1 gain fixed input terminal Pin No.
DV-L70S DV-L70BL DV-L70W 9-13. IC707 IX1473GE SERVO PROCCESSOR Pin No.
DV-L70S DV-L70BL DV-L70W Pin No.
DV-L70S DV-L70BL DV-L70W Pin No. 88 89 90 91 92 Terminal name BUS3 VDD VSS BUCK /CCE I/O I/O – – I I 93 TEST4 I 94 /TEMOD I 95 /RST I 96 TEST0 I 97 98 /HSO /UHSO O O 99 EMPH O 100 LRCK O Operation function Remarks Digital + power terminal. Digital ground terminal. Microcomputer interface clock input terminal. Microcomputer interface chip enable signal input terminal. BUS0 to 3 is active in “L” state. Test terminal. To be opened usually. Local test mode selection terminal.
DV-L70S DV-L70BL DV-L70W 9-14. IC801 PCM1716E Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Terminal name LRCIN DIN BCKI CLKO XTI XTO DGND VDD VCC2R AGND2R EXTR NC VOUTR AGND1 VCC1 VOUTL NC EXTL AGND2L VCC2L ZERO RSTB CS/IWO MODE MUTE MD/DM0 MC/DM1 ML/IIS AUDIO D/A CONVERTER I/O I I I O I O – – – – O – O – – O – O – – O I I I I I I I Operation function LRCK clock input (fs) (3) Data input (3) Bit clock input for data. System clock buffered output.
DV-L70S DV-L70BL DV-L70W 9-15. IC901 IX1516GE Terminal name Terminal 1 VDD GAMMA S-P-TONE In/Output – Input Input Input Input Input Input Function Digitan power +3.3V 2 3 4 5 6 7 HADR (0) HADR (1) HADR (2) HADR (3) HADR (4) HADR (5) CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus CPU Address bus 8 VSS – Digital GND 9 VDD – Digitan power +3.
DV-L70S DV-L70BL DV-L70W Terminal name Terminal 56 VSS In/Output – Function Digital GND 57 VDD – Digital power +3.3V 58 59 60 61 PXDI (4) PXDI (5) PXDI (6) PXDI (7) Input Input Input Input 62 63 TEST0 TEST1 Input Input Test terminal Test terminal 64 VSS – Digital GND • Block Diagram CPU 12 15 2 7 18 21 10 11 HADAT 29 HADR 8 8 Edge creation SPT circuit Source Dec.
DV-L70S DV-L70BL DV-L70W 9-17. IC1101 LZ9GJ19+-1 Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Terminal name VIN CVOP MON_E HSY VDD FRPT SYNI FRPV GND VCS NTPC VSY HRVC VRVC CLKC MDS GND EXCL GND MDW MDN PWM MON_F VSWC VCSWI VSWO VDD SPOI GND PCP CLOC MOD2 HR IHR PS CTR Operation function Pin No.
DV-L70S DV-L70BL DV-L70W 9-19. IC1801 IR3Y29BM Pin No.
DV-L70S DV-L70BL DV-L70W Pin No. 47 Terminal name AGC OUT 48 PICTURE Operation function It is the terminal which the voltage detected in the automatic gain control detector circuit of the luminance signal is outputted in. Output voltage rises the output voltage. The frequency characteristic of the luminance signal can do adjustment. When a voltage is lowered, emphasis is put on the contour.
DV-L70S DV-L70BL DV-L70W 9-21. IC2102 TK15400 Vcc • Block Diagram + Vcc=5.0V 33µF 1 Y-OUTPUT Vout 2.0Vp-p + 75Ω 8dB 75Ω DRIVER Y-INPUT 4.7µF 2 + 12 33µF 75Ω 1.5kΩ Clamp 1.25V 11 5kΩ 75Ω + 33µF 5kΩ CVBS-OUTPUT Vout 2.0Vp-p Standby Reference & Standby Logic 8dB 75Ω DRIVER 5 + 10 33µF 75Ω 1.5kΩ Clamp 1.25V BIAS 2.0V C-Input 4.7µF 5kΩ 33µF C-OUTPUT Vout 1.3Vp-p 100kΩ 8dB 75Ω DRIVER + 9 5kΩ 75Ω + 6 75Ω 3 4 + 8 33µF 75Ω 75Ω 7 GND 9-22. IC3200 IX1625GE Pin No.
DV-L70S DV-L70BL DV-L70W Pin No.
DV-L70S DV-L70BL DV-L70W Pin No.
DV-L70S DV-L70BL DV-L70W Pin No. 52 53 54 55 I/O O O O O 56 Terminal name LED1 AV S LED2 AV P Operation function LED control (green) DVD/TV control LED control (red) DVD/TV control DEF Defeat output 57 O EPCS EPROM chip select 58 O DACS DAC chip select 59 O FLOF DVD video mute 60 61 62 63 65 O I O IN H PSW SMUTE External input control Not used. Audio mute output O PMUTE Video mute output 79 O FMCS Not used. Remarks LED control “H” is output during TV tuner reception.
DV-L70S DV-L70BL DV-L70W 11-23. IC3201 MB8346BV Pin No. 17 14 16 I/O I O I Terminal name Data input terminal Data output terminal Shift clock input terminal 15 I 18, 19, 2, 3, 4, 5, 6, 7, 8, 9, 12, 13 11 20 10 1 O Remarks The 12-bit serial data is input. The bit data of MSB of 12-bit shift register is output. The input signal form the DI terminal is input into 12-bit shift register when the shift clock reises.
DV-L70S DV-L70BL DV-L70W 9-24.
DV-L70S DV-L70BL DV-L70W 9-26. IC3601 TK11835 BASE 1 Is 2 + - - 6 VCC 5 GND + Thermal S.D VFB 3 4 VREF VREF 1.Power amplification Tr base drive 2.Electric current limitation 3.Output voltage feedback 4.Reference voltage 5.GND 6.Input 9-27. IC6002 TDA7053 GND2 10 12(-) 9(+) 5 + IN2 SGND2 6 7 + 50 15 n.c. 11 n.c. 8 n.c. 4 n.c. 3 n.c.
DV-L70S DV-L70BL DV-L70W 9-28. IC9001 TL1451AC (9) (16) Vref=2.5V Error Amp1 (3) (4) (5) + VCC Reference Voltage 2.0V +2.5V (2) Trlangle Oscillator PWM Comprator1 1.4V (7) - Error Amp2 (12) (14) (13) (1) + Output1 Short Circuit Protection Comparator + + Vref/2 (10) Vref Vref R R Vref Output2 (15) PWM Comprator2 S Latch GND U.V.L.O.
DV-L70S DV-L70BL DV-L70W 10.
DV-L70S DV-L70BL DV-L70W 11.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 12. BLOCK DIAGRAMS 12-1.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 12-2.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 12-3.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 12-4.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 13. SCHEMATIC DIAGRAMS 13-1.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 13-2.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 13-3.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 13-4.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 13-5. POWER CIRCUIT SCHEMATIC DIAGRAM å AND SHADED COMPONENTS=SAFETY RELATED PARTS Note: It becomes Ref. NO. 90XX.
DV-L70S DV-L70BL DV-L70W 14. PRINTED WIRING BOARD ASSEMBLIES 14-1.
DV-L70S DV-L70BL DV-L70W DV-L70S DV-L70BL DV-L70W 14-2.
DV-L70S DV-L70BL DV-L70W 14-3. POWER/INVERTER PWB J POWER PWB Note: It becomes Ref. NO. 90XX. I H G F INVERTER PWB Component Side Note: It becomes Ref. NO. 99XX.
DV-L70S DV-L70BL DV-L70W Part No. ★ Description 15. REPLACEMENT PARTS LIST/ Code EXPLODED VIEWS Ref. No. Ref. No. ELECTRICAL PARTS LIST " HOW TO ORDER REPLACEMENT PARTS" ★MARK : SPARE PARTS-DELIVERY SECTION : ALL JAPAN To have your order filled promptly and correctly, please furnish the following informations. 2. REF. NO. 4. DESCRIPTION å MARK: SAFETY RELATED PARTS PWB ASSEMBLY IS NOT REPLACEMENT ITEM Ref. No. Part No.
DV-L70S DV-L70BL DV-L70W Ref. No. ★ Part No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. ★ Part No. Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. ★ Part No. Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No.
DV-L70S DV-L70BL DV-L70W MECHANISM EXPLODED VIEW Ref. No. ★ Part No. Description Code Ref. No. ★ Part No. Description Code H 1 8 G 7 F When replacement or a djustment of the parts in this frame is necessary, replace or adjust the mechanism ass'y (adjustment of the parts is completed). E 7 7 *2 5 15 11 *2 6 16 D *1 3 13 4 9 C 17 12 18 [Notes] *1. When soldering the sled lead wire y, it must be made in a soldering iron tip temperature of 290±20˚C and within 3 10 seconds. *2.
DV-L70S DV-L70BL DV-L70W CABINET EXPLODED VIEW Ref. No. ★ Part No. Description Code Ref. No. Part No.
DV-L70S DV-L70BL DV-L70W 16. OF THE SET Ref. PACKING No. Part No. ★ Description DV-L70S/BL Code Ref. No. ★SSAKA0170CEZZ(DV-L70S/BL) (Polystylene Bag, Accessories) TiNS-3709GEZZ(DV-L70S/BL) TiNS-3766GEZZ(DV-L70S/BL) (Operation Manual) Part No. ★ Description RPHOH0001GEZZ (EarPhone) UBATU0243GEZZ (Battery) å UADP-0195GEZZ (AC Adapter) TiNS-3710GEZZ(DV-L70S/BL) (Operation Manual) ★SPAKF0195GEZZ (Packing Meterial) ★SPAKX1065GEZZ ★SPAKX1066GEZZ (Packing Add.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description -Code M E MRef. O No. - 93 Part No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description - M E MRef. O No. - Code 94 Part No.
DV-L70S DV-L70BL DV-L70W Ref. No. Part No. ★ Description Code Ref. No. 95 Part No.
DV-L70S DV-L70S DV-L70BL DV-L70BL DV-L70W DV-L70W Ref. No. Part No. ★ Description Code Ref. No. ★ Part No. Description Code COPYRIGHT C 1999 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
