CD-BK300W Mini Component System consisting of CD-BK300W (main unit) and CPBK300 (speaker system). Mini-chaîne CD-BK300W composée de CD-BK300W (appareil principal) et de CP-BK300 (enceintes acoustiques). MINI COMPONENT SYSTEM MINI-CHAÎNE SISTEMA MINI Sistema mini CD-BK300W que consta de CD-BK300W (aparato principal) y CP-BK300 (sistema de altavoces).
ENGLISH Introduction Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. CAUTION - Introduction / Special Notes - Important Instruction Special Notes Laser Diode Properties Material: GaAIAs Wavelength: 780 nm Emission Duration: continuous Laser Output: max. 0.6 mW z This Mini Component System is classified as a CLASS 1 LASER product.
Accessories Contents Please confirm that the following accessories are included. Page „ General Information Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 6 „ Preparation for Use System Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 10 Remote Control . . . . .
Precautions „ General „ Volume control z Please ensure that the equipment is positioned in a well ventilated area and ensure that there is at least 10 cm (4") of free space along the sides, top and back of the equipment. The sound level at a given volume setting depends on speaker efficiency, location, and various other factors.
Controls and Indicators „ Front panel 9 10 11 1 2 3 4 5 12 13 14 18 19 20 21 15 16 17 22 23 24 25 Reference page 1. Disc Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2. Timer Set Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 3. On/Stand-by Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4. Tape 2 Cassette Compartment . . . . . . . . . . . . . . . . . . . . . . . . . .
Controls and Indicators (continued) „ Display 1 8 9 2 - Controls and Indicators - General Information 3 456 7 17 17 10 11 12 13 14 15 16 17 1 2 3 4 5 6 8 1 2 7 5 6 E-5 ENGLISH „ Rear panel Reference page 1. FM 75 Ohms Aerial Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 8 2. FM Aerial Earth Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7, 8 3. AM Loop Aerial Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
„ Remote control 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 - Controls and Indicators - 1 General Information Reference page 1. Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2. Echo Level Up and Down Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . 22 3. Karaoke Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4. Disc Number Select Buttons . . . . . . . . . . . . . . . . . . . . . . . . . .
System Connections - System Connections - Preparation for Use AM loop aerial Right speaker FM aerial Left speaker VCR, DVD, etc.
„ Aerial connection „ Speaker connection Supplied FM aerial: Main terminals: Connect the FM aerial wire to the FM 75 OHMS terminal and position the FM aerial wire in the direction where the strongest signal can be received. Subwoofer terminals: Connect the lower black wire to the MAIN (-) terminal and the blue wire to the MAIN (+) terminal. Connect the upper black wire to the SUBWOOFER (-) terminal and the red wire to the SUBWOOFER (+) terminal.
System Connections (continued) „ Placing the speaker system „ Setting the AC voltage selector The left and right speakers have individual shapes. For best performance, place the speakers according to the diagram below. Check the setting of the AC voltage selector located on the rear panel before plugging the unit into an AC socket. If necessary, adjust the selector to correspond to the AC power voltage used in your area.
„ Setting the FM/AM span selector „ Demonstration mode The first time the unit is plugged, the unit will enter the demonstration mode. You will see words scroll. To return to the demonstration mode: When the unit is in the power stand-by mode, press the X-BASS/DEMO button again. Note: When the power is on, the X-BASS/DEMO button can be used to select the extra bass mode. „ To change the display brightness (2 levels) You can switch the display brightness by pressing the DIMMER button.
Remote Control „ Battery installation „ Test of the remote control 1 Remove the battery cover. 2 Insert the batteries according to the direction indicated in the battery compartment. Face the remote control directly to the remote sensor on the unit. When inserting or removing the batteries, push them towards the nals. battery termi- The remote control can be used within the range shown below: Press the ON/STAND-BY button. Does the power turn on? Now, you can enjoy the music. 3 Replace the cover.
Sound Control „ Volume control Main unit operation: When the VOLUME control is turned clockwise, the volume will increase. When it is turned anti-clockwise, the volume will decrease. Remote control operation: button to increase the volume and the VOLUME 1 2 ..... 29 30 MAXIMUM „ Bass control When the power is first turned on, the unit will enter the extra bass mode which emphasises the bass frequencies, and "X-BASS" will appear. To cancel the extra bass mode, press the X-BASS/DEMO (X-BASS) button.
Setting the Clock 4 Press the TUNING/TIME ( or ) button to adjust the hour and then press the MEMORY/SET button. z Press the TUNING/TIME ( or ) button once to advance the time by 1 hour. Hold it down to advance continuously. z When the 12-hour display is selected, "AM" will change automatically to "PM". - Setting the Clock - Basic Operation 5 Press the TUNING/TIME ( or ) button to adjust the minutes and then press the MEMORY/SET button.
Listening to a CD (CDs) 1 2 3 4 Press the ON/STAND-BY button to turn the power on. Press the CD button. Press the OPEN/CLOSE button to open the disc tray. Place the CD(s) on the disc tray, label side up. When loading a third disc, press the DISC SKIP button to turn the disc tray, then place the CD in the open position. 12 cm (5") 5 Press the OPEN/CLOSE button to close the disc tray.
Listening to a CD (CDs) (continued) 7 Press the ( „ To locate the beginning of a track ) button to start playback. To move to the beginning of the next track: CD Playback - Listening to a CD (CDs) - Press the z Playback will begin from track 1 on the disc you have selected to play. After that disc finishes playing, the next disc will automatically start playback. z When the last track on the third disc has finished playing, the CD player will stop automatically.
Starting Playback with a Desired Track Repeat or Random Play „ Repeat Play All tracks on up to 3 discs, or a programmed sequence can be continuously repeated. You can play a disc starting with the desired track. To repeat all tracks on up to 3 discs: Whilst in the stop mode, press one of the 1 - 3 buttons or DISC SKIP button to select the desired disc. Press the ( ) button twice. Selected disc number To repeat a desired track: 2 Press the desired track.
Programmed Play By specifying discs from 1 to 3, and tracks from 1 to 99, you can choose up to 32 selections for playback in the order you like. 3 Press the MEMORY/SET (MEMORY) button to save the track number. Playback order When the track is memorised, "MEMORY" will appear. 4 Repeat steps 1 - 3 for other tracks. Up to 32 tracks can be programmed. 5 - Programmed Play - CD Playback If you make a mistake, the programmed tracks can be cleared by pressing the CLEAR button.
Listening to the Radio 1 2 Press the ON/STAND-BY button to turn the power on. 3 Press the TUNING/TIME ( station. Manual tuning: Press the TUNER (BAND) button repeatedly to select the desired frequency band (FM or AM). or ) button to tune in to the desired Press the TUNING/TIME button as many times as required to tune in to the desired station. Notes: z When radio interference occurs, auto scan tuning may stop automatically at that point. z Auto scan tuning will skip weak signal stations.
Listening to the Memorised Station „ To recall a memorised station „ Memorising a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) 1 2 Press the PRESET or PRESET 0.5 seconds to select the desired station. Perform the steps 1 - 3 in "Listening to the Radio" on page 18. Press the MEMORY/SET button to enter the preset tuning saving mode.
Listening to a Cassette Tape (TAPE 1) 1 2 3 Press the ON/STAND-BY button to turn the power on. 4 Load a cassette into the TAPE 1 cassette compartment with the side to be played facing toward you. 5 Press the 2) button to select TAPE 1. Open the cassette door by pushing the area marked " EJECT". ( ) button to start playback. To stop playback: Press the button. Note: You cannot fast-forward or rewind the cassette in the TAPE 1 compartment. Sound Control (See page 12.
Tape Playback - Listening to a Cassette Tape (TAPE 2) - Listening to a Cassette Tape (TAPE 2) 3 Open the cassette door by pushing the area marked " PUSH EJECT". 4 Load a cassette into the TAPE 2 cassette compartment with side A facing you. 5 Press the button to choose one side or both sides. ... To listen to both sides. ... For endless repeat play of both sides. ... To listen to one side. 6 Press the B.
Playing Karaoke 1 To protect the speakers from shock noise and to avoid disturbing noises, set the MIC LEVEL control to MIN. 2 Connect the microphone to the MIC socket. z Use a microphone with a 6.3 mm (1/4") plug, an impedance of 600 ohms. z If a microphone whose sensitivity is too high is used, howling may be generated. z Unidirectional microphone is more appropriate for vocal use. z Use a standard plug adaptor when using a microphone with a 3.5 mm (1/8") diameter plug.
Playing Karaoke (continued) „ To change general stereo source to karaoke sources Even ordinary discs and tapes not recorded specifically for karaoke can be used as karaoke discs and tapes just by toning down the main vocal. Press the KARAOKE MODE button until "V-CANCEL" appears in the display. z " " will appear. Notes: Karaoke - Playing Karaoke - z Use discs which have been recorded in stereo. The function will not work with mono sources.
Recording from the Radio 1 2 Tune in to the desired station. (See page 18.) Load a cassette into the TAPE 2 cassette compartment with side A facing you. Wind past the leader of the tape, on which recording cannot be performed. 3 Press the button to choose one side or both sides. ... To record on both sides. ... To record on only one side. Press the REC PAUSE button. ( ) Recording will be paused. 5 Press the side B.
Recording from a CD (CDs) You can record 3 CDs continuously. 1 2 Press the ON/STAND-BY button to turn the power on. Load a cassette into the TAPE 2 cassette compartment with side A facing you. Wind past the leader of the tape, on which recording cannot be performed. Press the CD button and load the desired disc. Press the button to choose one side or both sides. ... To record on both sides. ... To record on only one side. - Recording from a CD (CDs) - Tape Recording 3 4 5 Press one of the first.
Dubbing from Tape to Tape You can record from TAPE 1 to TAPE 2. 1 2 Press the ON/STAND-BY button to turn the power on. Load a prerecorded cassette into the TAPE 1 cassette compartment. Insert a blank tape into the TAPE 2 cassette compartment. It is recommended that the recording tape is the same length as the master tape. 3 Press the TAPE (1 2) button until "TAPE 1" appears on the display. Press the REC PAUSE button. ( ) Recording will be paused. 5 Press the ( ) button.
Timer and Sleep Operation Timer playback: The unit turns on and plays the desired source (CD, tuner, tape) at the preset time. „ Timer playback or Timer recording Before setting timer: Timer recording: The unit turns on and starts recording from the tuner at the preset time. 1 Press the CLOCK button to check that the clock is on time. Sleep operation: The radio, compact disc and cassette tape can all be turned off automatically.
„ Sleep operation 1 2 Play back the desired sound source. Press the TIMER/SLEEP button repeatedly until "SLEEP" is displayed. The unit will enter the timer stand-by mode automatically. To change the sleep time: While the sleep time is displayed, press the TUNING/TIME ( or ) button. (Maximum: 3 hours - Minimum: 1 minute) To cancel the timer playback/timer recording: z 3 hours - 5 minutes 5-minute intervals z 5 minutes - 1 minute 1-minute intervals Press the ON/STAND-BY button to turn the power on.
Enhancing Your System The connection lead is not included. Purchase a commercially available lead as shown below. VCR, DVD, etc. „ Listening to the playback sounds from VCR, DVD, etc. 1 Use a connection lead to connect the VCR, DVD, etc. to the VIDEO/ AUX sockets. When using video equipment, connect the audio output to this unit and the video output to a television. - Enhancing Your System - Advanced Features To the line output socket White 2 3 4 Press the ON/STAND-BY button to turn the power on.
Troubleshooting Chart Symptom z The clock is not on time. Possible cause z Did a power failure occur? Reset the clock. (Refer to page 13.) z When a button is pressed, the unit z Set this unit to the power stand-by mode and then turn it back on. does not respond. z If the unit still malfunctions, reset it. (Refer to step 3 under "If trouble occurs" on page 31.) z No sound is heard. Possible cause z Is the erase-prevention tab removed? z Is it a normal tape? (You cannot record on a metal or CrO tape.
Troubleshooting Chart (continued) Maintenance „ If trouble occurs „ Cleaning the tape-handling parts References - Troubleshooting Chart / Maintenance - When this product is subjected to strong external interference (mechanical shock, excessive static electricity, abnormal supply voltage due to lightning, etc.) or if it is operated incorrectly, it may malfunction. If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again.
Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.
