SERVICE MANUAL CODE: 00ZARNC5J/A1E DIGITAL LASER COPIER/PRINTER OPTION PRINT SERVER CARD MODEL AR-NC5J AR-NC5JG AR-NC5JW CONTENTS [1] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 [2] ENVIRONMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 [3] MAJOR FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 [4] IDENTIFICATION OF EACH SECTION AND FUNCTIONS . . . . . . . . .
[1] GENERAL The AR-NC5J is a print server with Falcon 32bit RISC chip, which automatically switches between 10BASE-T/100BASE-TX, conforming to network protocols of TCP/IP (Windows95, Windows98, WindowsMe, WindowsNT4.0, Windows2000, UNIX), IPX/SPX (Netware), AppleTalk (Macintosh), and NetBEUI (Windows95, Windows98, WindowsMe, WindowsNT4.0, Windows2000). The 32bit CPU, together with the automatic switch of 10/100BASE, provides high-speed process.
2. Jumper switches 2. Parts included Print server card: 1 1234 10BASE-T/ 100BASE-TX connector CD-ROM: 1 Screws (silver) Spacers (unused): 2 M3 x 8: 2 Operation manual: 1 Installation manual: 1 3. Installation procedure The AR-NC5J installing procedures in the AR-235/275 series are described. Jumper switch The jumper switch has No. 1 and No. 2 pins, and ON/OFF is switched by the jumper plug. When getting started, No. 1 pin is ON and the flash memory loader is started. When No.
3) Attach the print server card. Align the connector positions, connect the print server card, and then secure the card to the option mounting plate in the main unit using supplied two silver screws (M3 x 8). [6] AR-NC5J STATUS CHECK 1. Printing the status page The AR-NC5J status is checked by printing the status page. A. Example of status page print There are roughly two ways of printing the status page. Silver screws (M3 x 8) • Printing the status page is performed when starting the AR-NC5J.
2. AR-NC5J setup items After completion of installation, perform setup of the environmental variables. Explanations on the variables are given below. A. General Telnet Change root Password Name Web page Change Admin password NIC Manager Admin Password Factory setup Sharp Descriptions The administrator password of the AR-NC5J is set with ASCII character codes. This password is used for identification when changing setup by Telnet, a Web page, or a setup utility. Remark: Indicated as "*" for security.
Name Factory setup Telnet Web page NIC Manager Login Password Login Password Login Password No (No password) Job Polling (sec) Job Polling interval (sec) Job Polling interval 4 Bindary Mode Bindary Mode Bindary setup ENABLE FSERVER Name 1 – 8 File server name 1 – 8 Filer server name to be connected "" NDS Tree NDS Tree name NDS Tree name "" NDS Context NDS Context NDS Context "" PSERVER Name 1 – 8 Print Server name 1 – 8 Print Server name to be connected "" Job Timeout (sec) Job Time
[7] TROUBLESHOOTING Check that the printer port name is properly set. Check that the printer port name set to the AR-NC5J is identical to the printer port name set to the NetWare server. If there are two or more units of the AR-NC5J, do not use the same name for different AR-NC5J, and do not use the same port name for different ports. 1. Obstacles to introduction A. Test print is not outputted. Check that the printer is ready for printing. (Online/Offline, etc.
If the IPX/SPX protocol is available and there is a NetWare server in the environment, a network number may be obtained from the NetWare server to allow communication (retrieval and upload) with a print server card which is outside of the router. In the other environments, communication with a device outside the router cannot be made. B. Main menu When retrieval is completed, the main menu of the tool is displayed, and the list of retrieval results is displayed. 2.
E. Test print 1) Single selection When only one printer is selected from the list on the main menu: First the upload start confirmation display is shown. Selecting YES in this menu deletes the firmware and starts uploading. During uploading, the process indication bar is displayed on the firmware upload menu. After completion of uploading, the firmware upload menu is closed and the control returns to the main menu.
5. Error message list 6. Check for defectiveness of the AR-NC5J The table below shows the error messages list of the version up tool. Error message Occurring conditions Invalid firmware file. Select a The Bin file of the selected firmware correct file. was improper. (Example: A BIN file of other unit than the AR-NC5J was selected.) Can’t operate more than 32 Printers of over 32 units were selected units at the same time. and Uploading or test print was performed Upload failed.
CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. “BATTERY DISPOSAL” CONTAINS MANGANESE DIOXIDE LITHIUM BATTERY MUST BE DISPOSED OF PROPERLY.
All rights reserved. Printed No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic; mechanical; photocopying; recording or otherwise without prior written permission of the publisher. Trademark Acknowledgments Microsoft Windows, MS-DOS, Windows NT, Windows 2000 are trademarks of Microsoft Corporation in the U. S. A. and other countries.
