MODEL AR-203E DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL Page INTRODUCTION 4 LOADING PAPER 7 MAKING COPIES 12 INSTALLING THE SOFTWARE SPECIAL FUNCTIONS MAINTENANCE 20 42 TROUBLESHOOTING THE UNIT OPTIONS APPENDIX 45 50 58 61
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. Money Stamps Bonds Stocks Bank drafts Checks Passports Driver's licenses In some areas, the "POWER" switch positions are marked "I" and "O" on the copier instead of "ON" and "OFF".
CAUTIONS Caution label on the unit The label ( ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using Follow the cautions below when using this unit. Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes. • Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15 seconds before turning it back on.
Proper storage for supplies Store the supplies (paper and toner cartridges) in a location that is: • clean and dry • at a stable temperature • not exposed to direct sunlight. Store paper in the wrapper and lying flat. • Paper stored out of the wrapper or in packages standing on end may curl or get damp, resulting in paper misfeeds. Trademark acknowledgements • Microsoft and Windows are trademarks of Microsoft Corporation in the U.S.A. and other countries.
CONTENTS 1 INTRODUCTION USING THE MANUAL ................... 4 PART NAMES ............................... 5 OPERATION PANEL..................... 6 2 LOADING PAPER PAPER........................................... 7 LOADING THE PAPER TRAY....... 8 BYPASS FEED (including special paper) .......................................... 10 3 MAKING COPIES COPY FLOW ............................... 12 CONNECTING THE POWER CORD 13 ORIGINAL PLACEMENT............. 15 SET THE COPY QUANTITY .......
1 INTRODUCTION This chapter provides basic information for using the unit. USING THE MANUAL The operation manual contains explanations of how to operate the unit, important considerations, and maintenance procedures. To get the most out of the unit, please read the operation manual. Please keep the operation manuals in a suitable location that will allow for convenient future reference. Conventions used in the manual This operation manual explains the operation of the AR-203 model.
PART NAMES SPF as an option Exit area Original cover Original guide Document feeder cover Peep hole Document feeder tray 1 Interface USB connector SPF scan area (option) 1 2 7 9 10 8 3 11 12 13 4 5 6 Paper tray 2 as an option Toner cartridge 14 7 3 15 16 Photoconductive drum 1 2 3 4 5 6 7 8 9 Original table Operation panel Front cover Paper tray Side cover open button Multi-bypass tray Side cover Bypass paper guides Paper output tray 10 11 12 13 14 15 16 Paper output tray extension Po
OPERATION PANEL 1 2 3 141 A5 A4 86 70 A4 B5 A4 A5 Exposure mode selector key and indicators Use to sequentially select the exposure modes: AUTO, MANUAL or PHOTO. Selected mode is shown by a lit indicator. (p.17) Light and dark keys and indicators Use to adjust the MANUAL or PHOTO exposure level. Selected exposure level is shown by a lit indicator. (p.17) Use to start and terminate user program setting. (p.43) Alarm indicators Developer replacement required indicator (p.
2 LOADING PAPER Follow the steps below to load paper into the tray. PAPER For best results, use only paper recommended by SHARP.
LOADING THE PAPER TRAY 1 Raise the handle of the paper tray and pull the paper tray out until it stops. 2 Adjust the paper guides on the paper tray to the copy paper width and length. Squeeze the lever of paper guide A and slide the guide to match with the width of the paper. Move paper guide B to the appropriate slot as marked on the tray. Paper guide B 3 Paper guide A Fan the paper and insert it into the tray. Make sure the edges go under the corner hooks.
4 Gently push the paper tray back into the unit. • After loading paper, to cancel the blinking without restarting copying, press the clear ( ) key. The in the display will go out and the start ( ) indicator will light up. • Be sure that paper is free of rips, dust, wrinkles, and curled or bent edges. • Make sure all the paper in the stack is the same size and type.
BYPASS FEED (including special paper) The multi-bypass tray can be used to feed standard paper, transparency film, labels, envelopes, and other special purpose paper. Paper measuring from A6 to A4 and in the weight range of 56 to 128g/m2 can be used in this tray. (For paper weighing from 105 to 128g/m2, A4 is the maximum size.) • The multi-bypass tray can hold maximum of 50 sheets of paper. (Capacity will vary depending on the type of paper loaded.
• Paper must be fed narrow side into the feed slot. • Transparency film, labels, envelopes, and other special purpose papers must be fed individually. • When copying onto transparency film, remove each copy promptly. Do not let copies stack up. When loading an envelope, make sure that it is straight and flat. 3 Press the tray select ( ) key to select the multi-bypass tray. 2 Note for loading envelopes • Envelopes must be fed narrow side into the feed slot one at a time.
3 MAKING COPIES This chapter explains basic and other copying functions. The unit is equipped with a one-page memory buffer. This memory allows the unit to scan an original once only and make up to 99 copies. This feature improves workflow, reduces operation noise from the copier, and provides higher reliability by reducing wear and tear on the scanning mechanism. If the unit does not function properly during use, or if a function cannot be used, see "TROUBLESHOOTING THE UNIT" (p.50).
CONNECTING THE POWER CORD If you use the unit in a country other than the country where the unit was purchased, you will need to make sure that your local power supply is compatible with your model. If you plug the unit into an incompatible power supply, irreparable damage to the unit will result. 1 Ensure that the power switch of the unit is in the OFF position. Insert the attached power cord into the power cord socket at the rear of the unit.
About the scan head The scan head lamp remains on constantly when the unit is in the ready condition (when the start ( ) indicator is illuminated). The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not indicate unit trouble. Initial settings of operation panel When the unit power is on, the operation panel will revert to the initial settings when the time set with the "Auto clear time" setting (p.
ORIGINAL PLACEMENT Using the original table • The original table can read up to A4 original. • Image loss 4mm can occur at the leading and trailing edges of the copies. Also image loss 4.5mm in total can occur along the other edges of the copies. • When copying a book or an original which has been folded or a crumpled original, press down the original cover lightly. If the original cover is not securely closed, the copies may be striped or blurred.
Using the SPF The SPF is designed to hold up to 50 originals measuring from A5 to A4 and weighting from 56 to 90 g/m2. • Before feeding originals in the original feeder tray, be sure to remove any staples or paper clips from them. • Before placing curled or wavy originals into the original feeder tray, be sure to flatten them. If not, original misfeeds may result. • The SPF ( ) indicator on the operation panel will light up.
SET THE COPY QUANTITY Set the number of copies using the two copy quantity ( from the original table or from the SPF if installed. , ) keys when copying • Press the clear ( ) key to clear an entry if a mistake is made. • A single copy can be made with the initial setting, i.e., when "0" is displayed. • Press the right copy quantity key to set the unit digit from 0 to 9. This key will not change the tens digit. • Press the left copy quantity key to set the tens digit from 1 to 9.
Automatic exposure adjustment This automatic exposure level will remain in effect until you change it again by this procedure. The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the SPF respectively. 18 1 When adjusting the automatic exposure level for copying from the SPF, place an original in the original feeder tray and make sure that the SPF ( ) indicator lights up.
REDUCTION/ENLARGEMENT/ZOOM Three preset reduction ratios and two enlargement ratios can be selected. The zoom function enables copy ratio selection from 25% to 400% in 1% increments. 1 Set the original and check the paper size. 2 Use the copy ratio selector key and/or ZOOM ( select the desired copy ratio. , ) keys to • To verify a zoom setting without changing the zoom ratio, press and hold down the copy ratio display (%) key.
4 INSTALLING THE SOFTWARE This chapter explains how to install and configure the software that is required for the printer and scanner functions of the machine. The procedure for viewing the Online Manual is also explained. • The screen images in this manual are mainly for Windows XP. With other versions of Windows, some screen images may be different from those in this manual. • This manual refers to the CD-ROM that accompanied the machine simply as "CD-ROM".
BEFORE INSTALLATION Hardware and software requirements Check the following hardware and software requirements in order to install the software. Computer type IBM PC/AT or compatible computer equipped with a USB 2.
INSTALLING THE SOFTWARE • In the following explanations it is assumed that the mouse is configured for right hand operation. • The scanner function only works when using a USB cable. • If an error message appears, follow the instructions on the screen to solve the problem. After the problem is solved, the installation procedure will continue. Depending on the problem, you may have to click the "Cancel" button to exit the installer.
7 To install all of the software, click the "Standard" button and go to step 12. To install particular packages, click the "Custom" button and go to next step. 8 Click the "MFP Driver" button. Click the "Display Readme" button to show information on packages that are selected. 4 9 Select "Connected to this computer" and click the "Next" button. Follow the on-screen instructions. When "The installation of the SHARP software is complete." appears, click the "OK" button and go to step 12.
10 You will return to the window of step 8. If you wish to install Button Manager or Sharpdesk, click the "Utility Software" button. If you do not wish to install the Utility Software, click the "Close" button and go to step 12. After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer. Installing the Utility Software 11 Click the "Button Manager" or the "Sharpdesk" button.
After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer. 13 Make sure that the power of the machine is turned on, and then connect the USB cable (p. 26). Windows will detect the machine and a Plug and Play screen will appear. 14 Follow the instructions in the plug and play window to install the driver. Follow the on-screen instructions.
Connecting a USB cable Follow the procedure below to connect the machine to your computer. A USB cable for connecting the machine to your computer is not included with the machine. Please purchase the appropriate cable for your computer. • USB is available with a PC/AT compatible computer that was originally equipped with USB and had Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or Windows Vista preinstalled. • Do not connect the USB cable before installing the printer driver.
3 Click the "Printer Driver" button. 4 Select "Connected via the network" and click the "Next" button. Click the "Display Readme" button to show information on packages that are selected. 4 5 Click the "Add Network Port" button. If you are using Windows 98/Me/2000/XP, you can also click the "Add Network Port" button and select the printer to be shared by browsing the network in the window that appears. (On Windows Vista, the "Add Network" Port" button does not appear.
7 In the printer port selection window, verify the network printer that is shared and whether the machine is to be used as the default printer, make the selections and click the "Next" button. Follow the on-screen instructions. • If you are using Windows Vista and a security warning window appears, be sure to click "Install this driver software anyway".
INDICATORS ON THE OPERATION PANEL To configure the appropriate settings in the print server, see the operation manual or help file of your operating system. The ONLINE indicator and the start ( scanner. ) indicator indicate the state of the printer or SCAN indicator ONLINE indicator Start indicator Power save indicator Start indicator On: Indicates the unit is ready for copying or scanning is being performed. Blinking: The indicator blinks in the following situations: • When a print job is interrupted.
USING THE PRINTER MODE For problems with the printer function, see the online manual or the help file for the driver. Opening the printer driver from the start menu Open the printer driver setup screen by the method shown below. 1 Click the "start" button. 2 Click "Control Panel", select "Printers and Other Hardware", and then click "Printers and Faxes". • On Windows Vista, click "Control Panel", and then click "Printer". • On Windows 98/Me/2000, select "Settings" and click "Printers".
How to print 1 Make sure that the paper of the desired size and type is loaded in the tray. The procedure for loading paper is the same as for loading copy paper. See "LOADING PAPER" (p.7). 2 Open the document you intend to print, and select "Print" from the application's "File" menu. 3 Make sure that "SHARP AR-xxxx" is selected as the current printer. If you intend to change any print setting, click the "Preferences" button to open the setting dialog. On Windows 98/Me, click the "Properties" button.
USING THE SCANNER MODE Button Manager is a software program that works with the scanner driver to enable scanning from the machine. To scan using the machine, Button Manager must be linked with the scan menu on the machine. Follow the steps below to link Button Manager to scanner events. For problems with the scanner function, see the online manual or the help file for the driver.
Windows 98/Me/2000 To scan directly into an application using the Button Manager on Windows 98, Windows Me and Windows 2000. Set the Event Manager properties to send only to Button Manager as shown below. 1 Click the "Start" button, select "Control Panel" from "Settings", and open "Scanners and Cameras" in start menu. In Windows Me, it occasionally happens that the "Scanners and Cameras" icon does not appear immediately after installation of the MFP driver is completed.
Scan Button Destination Setting Dialog Box After you have completed the Button Manager settings in Windows, configure the scan settings in Button Manager. To configure the scan settings in Button Manager, right click the ( ) icon in the Taskbar and select "Setting" from the menu that appears. For details on configuring the scan settings in Button Manager, see the online manual or the help file.
Flow of the Button Manager setting The Button Manager can directly handle an AR-xxxx (where xxxx is the model name of your unit) series device event and start your selected application according to the scan setting made on the AR-xxxx (where xxxx is the model name of your unit) operation panel (SC1, SC2, SC3, SC4, SC5, SC6). This will scan directly into your application from the device. Scanner SCAN key pressed. Event Manager Button Manager Windows OS No Selection dialog is displayed.
All About The Windows Event Manager and scanner events in Windows 98, Windows Me, Windows 2000, Windows XP and Windows Vista Windows Platforms provide a mechanism for software to handle external events for a scanner device like the SHARP AR-xxxx (where xxxx is the model name of your unit) series products. This mechanism is controlled by the device manager on a device basis.
Using the SCAN key to begin scanning • Scanning is not possible during a copy job. • If the SCAN ( ) key is pressed during a print job, the scan job will be stored. • When scanning an original that has been placed in the SPF, only one original can be placed unless you are using Sharpdesk. 1 Press the SCAN ( ) key. The unit enters scan mode. 2 Place the original you wish to scan on the document glass/SPF.
4 Press the start ( ) key. Scanning will start and the scanned data will be transferred to the application. • If the following screen appears, select Button Manager and click "OK". Button Manager starts and the application associated with Button Manager starts. If you want only Button Manager to start in this case, set up Button Manager for use in Windows as explained in "Setting up the Button Manager" (p.32).
Using the SHARP TWAIN 1 Place the original(s) you wish to scan on the document glass/SPF. For the procedure for placing the original, see "ORIGINAL PLACEMENT" (p.15). 2 After starting Sharpdesk, click the "File" menu and select "Select Scanner". 3 Select "SHARP MFP TWAIN S", and click the "Select" button. WIA-SHARP AR-xxxx If you use more than one scanning device, select the scanner you want to use through the application.
Scanning with the "Scanner and Camera Wizard" in Windows XP Windows XP includes as a standard feature an image scanning function. The procedure for scanning with the "Scanner and Camera Wizard" is explained here. To cancel scanning, click the "Cancel" button in the screen that is displayed. 1 Place the original you wish to scan on the document glass/SPF. 2 Click the "start" button, select "Control Panel", and click "Printers and Other Hardware", and then click "Scanners and Cameras" in the start menu.
HOW TO USE THE ONLINE MANUAL The online manual provides detailed instructions for operating the unit as a printer or scanner and a list of methods for dealing with printing or scanner problems. To access the online manual, your computer must have Acrobat Reader 6.0 or a later version. 1 Turn on your computer. 2 Insert the supplied CD-ROM into your CD-ROM drive. 3 Click the "start" button, click "My Computer" ( double-click the CD-ROM ( ) icon.
5 SPECIAL FUNCTIONS This chapter describes the special functions of this unit. Use these functions as needed. DESCRIPTION OF SPECIAL FUNCTIONS Toner save mode (page 42) Reduces toner consumption by approximately 10%. Power save modes (page 43) The unit has two power save modes of operation: preheat mode and auto power shut-off mode. Preheat mode When the unit enters the preheat mode, the power save ( ) indicator will light up and other indicators will remain on or off as before.
3 To enter the toner save mode, press the light ( ) key. The light and dark indicator marked "1" will light up, indicating the toner save mode is selected. 4 Press the exposure mode selector key. The PHOTO ( ) indicator will stop blinking and will light up steadily. The light and dark indicator marked "3" will light up. The toner save mode is now active. To return to the standard mode, repeat the procedure but use the dark ( ) key to select exposure level "5" in step 3.
Program No. Mode Parameters 6 SPF automatic original discharge time (if installed) 1 3 5 5 min., *2 60 min., 4 240 min., 6 30 min., 120 min.
6 MAINTENANCE This chapter describes how to replace the toner cartridge and how to clean unit. Be sure to use only genuine SHARP parts and supplies. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered, and tested to maximise the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.
3 Gently pull the toner cartridge out while pressing the lock release lever. Toner cartridge lock release lever • After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge. • Dispose of the old toner cartridge in accordance with local regulations. 4 Remove the toner cartridge from the bag.
6 Close the front cover and then the side cover by pressing the round projections near the side cover open button. The indicator ( ) will go out and the start ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.
CLEANING THE UNIT Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to regularly clean the unit. Do not spray flammable cleaner gas. Gas from the spray may come in contact with the internal electrical components or high-temperature parts of the fusing unit, creating a risk of fire or electrical shock. • Before cleaning, be sure to turn the power switch off and remove the power cord from the outlet. • Do not use thinner, benzene or other volatile cleaning agents.
Transfer charger If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. 1 Turn the power switch off. (p.14) 2 Open the multi-bypass, then the side cover while pressing the side cover open button. 3 Take the charger cleaner out by holding the tab. Set the charger cleaner onto the right end of the transfer charger, gently slide the cleaner to the left end, and then remove it. Repeat this operation two or three times.
7 TROUBLESHOOTING THE UNIT This chapter describes misfeed removal and troubleshooting. TROUBLESHOOTING If any problem occurs, check the list below before contacting your authorised service representative. For problems with the printer function or the scanner function, see the online manual or the Help file for the printer/scanner driver. Problem Possible cause Solution Unit plugged in? Plug the unit into a grounded outlet. Power switch on? Turn the power switch on.
STATUS INDICATORS When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page. Be sure to use only genuine SHARP parts and supplies. Indication Cause and remedy Developer Steadily replacement required lit indicator Steadily Toner cartridge lit replacement required indicator Blinking Developer is required.
MISFEED REMOVAL When the misfeed ( ) indicator blinks or blinks in the display, the unit will stop because of a misfeed. If a misfeed occurs when using the SPF, a number may appear in the display after a minus sign. This indicates the number of the originals that must be returned to the original feeder tray after a misfeed. Return the required number of originals. Then this number will disappear when copying is resumed or the clear ( ) key is pressed.
A: Misfeed in the paper feed area 1 Gently remove the misfed paper from the paper feed area as shown in the illustration. When the misfeed ( ) indicator blinks, and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to "B: Misfeed in the fusing area". The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury.
2 Gently remove the misfed paper from under the fusing unit as shown in the illustration. If the paper cannot be removed, proceed to "C: Misfeed in the transport area". The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury. • Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may cause smudges on copies. • Do not remove the misfed paper from above the fusing unit.
4 5 Raise the fusing unit release lever, close the front cover and then close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the start ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.
(B) Open the original cover and rotate the roller rotating knob to remove the misfed original from the exit area. If the misfed original cannot be easily removed, proceed to (C). Roller (C) If the original does not move easily into the exit area, remove it in the direction of the arrow while rotating the knob. A number may appear in the display after a minus sign, indicating the number of the originals that must be returned to the original feeder tray.
SCAN HEAD LOCKING SWITCH The scan head locking switch is under the original table. If the switch is locked ( the unit will not operate. Unlock the switch ( ) as shown below. ), Grasp here and turn in the direction of the arrow. A Lock Unlock To lock the scan head locking switch, hold up the catch in illustration A and turn the center knob counter-clockwise 90 degrees until you hear a click.
8 OPTIONS SYSTEM CONFIGURATION A number of options are available for the unit which allow you to configure a system to meet your particular needs. The options include the following. Single Pass Feeder (AR-SP9) 250-sheet paper feed unit (AR-D33) AR-203E SINGLE PASS FEEDER (AR-SP9) The single pass feeder (SPF) holds up to 50 originals for automatic feeding. The procedures for placing originals in the SPF, cleaning the SPF, and removing a misfeed are explained in the following sections.
IF A PAPER MISFEED OCCURS IN THE MAIN UNIT WHEN USING THE SPF If a paper misfeed occurs in the main unit paper path when making copies with original(s) through the SPF, the SPF will automatically stop scanning. Manually remove the misfed paper(s) in the main unit. You can check the number of originals that must be returned to the document feeder tray in the display on the operation panel. Follow the steps below to display the number of originals to be returned.
250-SHEET PAPER FEED UNIT (AR-D33) The paper feed unit provide the convenience of increased paper capacity for the unit and a greater choice of paper size readily available for copying. The procedures for loading paper in the paper tray of paper feed unit, changing the paper size, and selecting the paper tray are same as for the paper tray in the unit. See "LOADING THE PAPER TRAY" (p.8) and "Selecting the tray" (p.19).
9 APPENDIX SPECIFICATIONS Model AR-203E Type Digital multifunctional system, desk-top type Copy system Dry, electrostatic transfer Originals Sheets, bound documents Printer function Available - Cable required (USB) Scanner function Available - Cable required (USB) Paper tray 250 sheets Multi-bypass tray 50 sheets Paper output tray 200 sheets Original sizes Original feed Max. A4 Original table 1 sheet SPF Up to 50 sheets Copy / printing size A6 to A4 *1 Image loss Max. 4mm *2 Max.
Model Sensor AR-203E Colour CCD Scanning speed Max. 2.88ms/line Memory 8 MB Local voltage ±10% (For this copier power supply, see the name plate located on the back of the unit) Power supply Power consumption Overall dimensions Width Depth Weight (Approximately) *4 Width 1000 W 607.6mm 462.5mm 16kg 518mm Unit dimensions Depth 462.5mm Height 295.6mm Operating conditions Temperature: 10°C to 30°C Humidity: 20% to 85% Emulation SHARP GDI Interface port USB interface (USB 2.
Single pass feeder (AR-SP9) Acceptable originals Weight: 56g/m2 to 90g/m2 Size: A5 to A4 Capacity: Up to 50 sheets Power supply Drawn from the unit. Weight Approx.
ABOUT SUPPLIES AND OPTIONS When ordering supplies, please use the correct part numbers as listed below. Be sure to use only genuine SHARP parts and supplies. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package. Supply list Supply Part number Usable life Toner cartridge AR-208T Approx.
INDEX 2 D 250-sheet paper feed unit ....................60 Dark key .......................................... 6, 17 Developer replacement required indicator .................................... 6, 51, 56 Developer required .............................. 56 Display................................................... 6 Displaying total number of copies........ 44 A About supplies .....................................64 Alarm indicator - Developer replacement required indicator.............................
- Paper feed area...............................53 - SPF .................................................55 - Transport area.................................54 Multi-bypass tray..................................10 N Name - Operation panel.................................6 - Part names ........................................5 O ONLINE indicator .............................6, 29 ONLINE key .....................................6, 29 Online manual......................................
INDEX BY PURPOSE Cleaning the unit - Cabinet ............................................48 - Original cover ..................................48 - Original table ...................................48 - SPF .................................................48 - Transfer changer .............................49 Connecting a USB interface cable .......26 Copying................................................12 Displaying total number of copies ........44 Enlarging/reducing copies....................
MATERIAL SAFETY DATA SHEET Page : 1/4 Date Issued : Nov. 1, 2007 MSDS No. F-01601 1.PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-208NT/ AR-208T (Black Toner) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) (Name and Telephone Number) U.S.A.
MATERIAL SAFETY DATA SHEET Page : 2/4 Date Issued : Nov. 1, 2007 MSDS No. F-01601 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.
MATERIAL SAFETY DATA SHEET Page : 3/4 Date Issued : Nov. 1, 2007 MSDS No. F-01601 Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 3 : 15mg/m (Total Dust), 3 : 10mg/m (Total Dust), 3 5mg/m (Respirable Dust) 3 3mg/m (Respirable Dust) : Not required under intended use. : Not required under intended use. : Not required under intended use. : Not required under intended use.
MATERIAL SAFETY DATA SHEET Chronic Effect Page : 4/4 Date Issued : Nov. 1, 2007 MSDS No.
MATERIAL SAFETY DATA SHEET Page : 1/4 Date Issued : Nov.01, 2007 MSDS No. F-31601 1.PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-208ND / AR-208DV (Black Developer) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) (Name and Telephone Number) U.S.A.
MATERIAL SAFETY DATA SHEET Page : 2/4 Date Issued : Nov.01, 2007 MSDS No. F-31601 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.
MATERIAL SAFETY DATA SHEET Page : 3/4 Date Issued : Nov.01, 2007 MSDS No. F-31601 Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 3 : 15mg/m (Total Dust), 3 : 10mg/m (Total Dust), 3 5mg/m (Respirable Dust) 3 3mg/m (Respirable Dust) : Not required under intended use. : Not required under intended use. : Not required under intended use. : Not required under intended use.
MATERIAL SAFETY DATA SHEET Chronic Effect Page : 4/4 Date Issued : Nov.01, 2007 MSDS No.
A. Information on Disposal for Users (private households) 1. In the European Union Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin! Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment.
CAUTION CLASS 3B INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. VORSICHT UNSICHTBARE LASERSTRAHLUNG DER KLASSE 3B, WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN. ADVARSEL USYNLIG LASERSTRÅLING AF KLASSE 3B VED ÅBNING, NÅR SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING. Laserstrahl ADVARSEL USYNLIG KLASSE 3B LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
SHARP Manufacturing France S.A.
AR-203E OPERATION MANUAL AR-203E_v1
