MODEL AR-156 DIGITAL LASER COPIER OPERATION MANUAL Page • GETTING STARTED 3 • MAKING COPIES 12 • SPECIAL FUNCTIONS 20 • SUPPLIES AND USER MAINTENANCE 23 • COPIER TROUBLE? 27 • APPENDIX 36 • OPTIONAL EQUIPMENT 40
FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit.
CONTENTS 1 GETTING STARTED INTRODUCTION 3 CAUTIONS 4 MAIN FEATURES 5 PART NAMES 6 OPERATION PANEL 7 COPIER INSTALLATION 8 CAUTIONS ON HANDLING 9 LOADING COPY PAPER 10 2 MAKING COPIES NORMAL COPYING 12 – Stream feeding mode 16 EXPOSURE ADJUSTMENT/PHOTO COPYING REDUCTION/ENLARGEMENT/ZOOM 17 BYPASS FEED (including special paper) 18 3 16 SPECIAL FUNCTIONS DESCRIPTION OF SPECIAL FUNCTIONS 20 TONER SAVE MODE 20 USER PROGRAMS (power save modes, auto clear time, stream feeding mode) 21 – Setting the power sav
CONTENTS 4 SUPPLIES AND USER MAINTENANCE TONER CARTRIDGE REPLACEMENT – Toner cartridge life 25 USER MAINTENANCE 5 23 25 – Cabinet 25 – Original table and original cover – Transfer charger – When copier is not in use 25 26 26 COPIER TROUBLE? MISFEED REMOVAL 27 – A Misfeed in the paper feed area – B Misfeed in the fusing area 28 – C Misfeed in the transport area – D Misfeed in the RSPF 30 DEVELOPER REQUIRED 32 MAINTENANCE REQUIRED TROUBLESHOOTING 28 29 32 33 STATUS INDICATORS
GETTING STARTED This chapter provides basic information for using the copier. 1 INTRODUCTION Getting started This copier has been designed to provide intuitive operating ease while requiring a minimum amount of space. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. This copier can also be used as a laser printer if an optional printer expansion kit is installed.
CAUTIONS Follow the cautions below when using this copier. ● The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. ● Do not switch the copier rapidly on and off. After turning the copier off, wait 10 to 15 seconds before turning it back on. ● Copier power must be turned off before installing any supplies. ● 1 Getting started .● Place the copier on a firm, level surface.
MAIN FEATURES High-speed laser copying Since warm-up time is zero, copying can be started immediately after the power switch is turned on. ● First-copy time is only 9.6 seconds (normal mode). ● Copying speed is 15 copies/min., which adapts to business use, allowing improvement of working efficiency. 1 Getting started ● High-quality digital image ● High-quality image copying at 600 dpi can be performed. ● In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.
Original guides RSPF exit area PART NAMES Document feeder tray Original table Feeding roller cover Original cover 1 Getting started Operation panel Side cover Bypass tray Bypass tray guides Paper tray Front cover Side cover open button Handle Cover for optional printer interface * A printer expansion kit is optional.
OPERATION PANEL 1 Getting started Original to copy key and indicators : Two-sided copies from onesided originals. Turn on Long Edge or Turn on Short Edge can be selected. : Two-sided copies from twosided originals. (Can be selected only when the RSPF is used.) : One-sided copies from twosided originals. (Can be selected only when the RSPF is used.) Exposure mode selector key and indicators Use to sequentially select the exposure modes: AUTO, MANUAL or PHOTO. Selected mode is shown by a lit indicator. (p.
COPIER INSTALLATION Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
COPIER INSTALLATION Be sure to allow the required space around the machine for servicing and proper ventilation. 8"(20 cm) 4" (10 cm) 8"(20 cm) 4" (10 cm) 1 Getting started A small amount of ozone is produced within the copier during operation. The emission level is insufficient to cause any health hazard. NOTE: The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.
LOADING COPY PAPER Raise the handle of the paper tray and pull the paper tray out until it stops. 1 Getting started Adjust the paper guides on the paper tray to the copy paper width and length. Squeeze the lever of paper guide and slide the guide to match with the width of the paper. to the appropriate slot as marked on the tray. Move paper guide Paper guide B Paper guide A Fan the copy paper and insert it into the tray. Make sure the edges go under the corner hooks.
LOADING COPY PAPER Gently push the paper tray back into the copier. After loading copy paper, to cancel the blinking “P” without restarting copying, press the clear ( ) key. The “P” in the display will go out and the ready ( ) indicator will light up.
MAKING COPIES This chapter describes basic copying functions and some other copying functions using the bypass tray. NORMAL COPYING 2 Making copies This copier has two document input stations -reversing single pass feeder (RSPF) for automatic document feeding and an original table for manual handling of documents. The RSPF is designed to hold up to 30 originals measuring from 5-1/2" x 8-1/2" to 10" x 14" and weighing from 14 to 23 lbs.
NORMAL COPYING Turn the power switch on. The ready ( ) indicator will light up. ● The copier will enter a power save mode once the set time has elapsed without any copier operation after the last copy of a run is made or power is turned on. The settings of the power save modes can be modified. See page 21, USER PROGRAMS. ● The copier will return to the initial settings a preset amount of time after the last copy is made. The preset amount of time (auto clear time) can be changed.
NORMAL COPYING Original face up B. When using the original table: (1) Open the original cover. (2) Place an original face down on the original table. Align it with the original scale and the centering ( ) mark. Close the original cover. 2 Making copies Original scale mark When copying a book or an original which has been folded or a crumpled original, press down the original cover lightly. If the original cover is not securely closed, the copies may be striped or blurred.
NORMAL COPYING D. When copying in the two-sided to one-sided mode: Use the original to copy key to select the two-sided to one-sided copying mode. The originals must have been set in the RSPF in step 3. A B C D 2 Ensure that the desired paper tray is selected. Making copies ● Paper sizes that can be used in the duplex copy mode are letter, legal, and invoice. (When copying from the original table in the duplex copy mode, only letter size paper can be used.
NORMAL COPYING When making two-sided copies from the original table, place the second original on the original table and press the print ( ) key. 2 ● Making copies To cancel two-sided copying after scanning the first original, press the clear ( ) key. Stream feeding mode The stream feeding mode allows easy operation of continuous copying from the RSPF. If the stream feeding mode has been enabled using user program No.
NORMAL COPYING Set the number of copies using the copy quantity ( ( ) key. , ) keys and press the print 2 Making copies REDUCTION/ENLARGEMENT/ZOOM Three preset reduction ratios and two enlargement ratios can be selected. The zoom function enables copy ratio selection from 50% to 200% in 1% increments. Set the original and check the copy paper size. Use the copy ratio selector key and/or zoom ( ratio.
BYPASS FEED (including special paper) The bypass tray can automatically feed up to 50 sheets of standard copy paper and can also feed special papers such as transparency film and labels one sheet at a time. Copy paper measuring from 3-1/2" x 5-1/2" to 8-1/2" x 14" and in the weight range of 14 to 34.5 lbs. can be used in this tray. (For paper weighing from 28 to 34.5 lbs., 8-1/2" x 11" is the maximum size.) Place the original(s) face up in the document feeder tray or face down on the original table.
BYPASS FEED Print face Press the tray select ( ) key to select the bypass tray. Set the number of copies if using standard copy paper. Press the print ( ) key.
SPECIAL FUNCTIONS This chapter describes the special functions of this copier. Use these functions as needed. DESCRIPTION OF SPECIAL FUNCTIONS Toner save mode (page 20) Reduces toner consumption by approximately 10%. 3 Power save modes (page 21) Special functions The copier has two power save modes of operation: preheat mode and auto power shut-off mode.
TONER SAVE MODE Press and hold down the exposure mode selector key for approximately 5 seconds. The manual ( ) indicator will go out and the photo ( ) indicator will begin to blink. The exposure indicator marked “5” will light up, indicating the standard toner mode is active. To enter the toner save mode, press the light ( ) key. The exposure indicator marked “1” will light up, indicating the toner save mode is selected. 3 Special functions Press the exposure mode selector key twice.
USER PROGRAMS Press the print ( ) key. The entered program number will be steadily lit and the currently selected parameter number for the program will blink on the right side of the display. Select the desired parameter using the right copy quantity ( parameter number will blink on the right of the display. Program No. 3 Mode ) key. The entered Parameters Special functions 1 Auto clear time 0 3 OFF 90 sec. 1 4 30 sec. * 2 120 sec. 5 60 sec. 10 sec. 2 Preheat mode 0 30 sec. 1 60 sec.
SUPPLIES AND USER MAINTENANCE This chapter describes how to replace the toner cartridge . Be sure to use only genuine SHARP parts and supplies. TONER CARTRIDGE REPLACEMENT When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner cartridge replacement required ( ) indicator blinks, the toner cartridge must be replaced before copying can be resumed.
TONER CARTRIDGE REPLACEMENT Remove the toner cartridge from the bag. Hold the cartridge on both sides and shake it horizontally four or five times. 4 or 5 times Gently insert the toner cartridge along the guides until it locks in place while pushing the lock release lever. Pull out the shutter and remove it from the toner cartridge as shown in the illustration. 4 Supplies and user maintenance Close the front cover and then the side cover by pressing the round projections near the side cover open button.
TONER CARTRIDGE REPLACEMENT Toner cartridge life To find out the approximate quantity of toner remaining, follow the procedure below. Press and hold down the light ( ) and dark ( 5 seconds until all the alarm indicators ( the display. , ) keys simultaneously for more than , and ) blink and “– –” appears in Press and hold down the copy ratio display ( ) key for more than 5 seconds. The approximate quantity of toner remaining will be indicated in the display as a percentage.
USER MAINTENANCE Transfer charger If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. Turn the power switch off. Ensure that the bypass tray is open and then open the side cover while pressing the side cover open button. Take the charger cleaner out by holding the tab. Set the charger cleaner onto the right end of the transfer charger, gently slide the cleaner to the left end, and then remove it.
COPIER TROUBLE? This chapter describes misfeed removal and troubleshooting. MISFEED REMOVAL When the misfeed ( ) indicator blinks or blinks in the display, the copier will stop because of a misfeed. If a misfeed occurs when using the RSPF, a number may appear in the display after a minus sign. This indicates the number of the originals that must be returned to the document feeder tray after a misfeed. Return the required number of originals.
MISFEED REMOVAL A Misfeed in the paper feed area Gently remove the misfed paper from the paper feed area as shown in the illustration. When blinks in the display and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to “B Misfeed in the fusing area”. The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury.
MISFEED REMOVAL ● Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. ● Do not remove the misfed paper from above the fusing unit. Unfixed toner on the paper may stain the paper transport area, resulting in smudges on copies. Raise the fusing unit release lever and then close the side cover by pressing the round projections near the side cover open button.
MISFEED REMOVAL Rotate the feeding roller in the direction of the arrow and gently remove the misfed paper from the exit area. Feeding roller Raise the fusing unit release lever, close the front cover and then close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the ready ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover.
MISFEED REMOVAL Roller rotating knob With the RSPF, pull out the reversing tray to remove the misfed original. With the RSPF, after removing the misfed original from the exit area, be sure to insert the reversing tray into the exit area until it locks in place. 5 Copier trouble? (C) If the original does not move easily into the exit area remove it in the direction of the arrow while rotating the knob.
DEVELOPER REQUIRED When the indicator lights up, the developer should be replaced.DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN AUTHORIZED SHARP SERVICE TECHNICIAN. Contact your service center as soon as possible. MAINTENANCE REQUIRED When indicator lights up, service by an authorized SHARP service technician is required. Contact your service center as soon as possible.
TROUBLESHOOTING If any problem occurs, check the list below before contacting your SHARP service center. Problem Possible cause Copier plugged in? Power switch on? Side cover closed securely? Front cover closed? Copier does not operate. Blank copies Power save ( indicator on. ) Dust, dirt, smudges appear on copies. Striped copies Paper misfeeds frequently. Images rub off the copy easily.
STATUS INDICATORS When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page. Be sure to use only genuine SHARP parts and supplies. Indication Cause and remedy Developer replacement Steadily Developer is required. Contact your SHARP service center as soon as possible.
AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the RSPF respectively. When adjusting the automatic exposure level for copying from the RSPF, place an original in the document feeder tray and make sure that the RSPF ( ) indicator lights up. When adjusting the level for copying from the original table, make sure that no original is left in the document feeder tray.
APPENDIX SPECIFICATIONS 6 Appendix 36 Type Digital laser copier, desk-top type Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original size Max. 10" x 14" (5-1/2" x 8-1/2" to 10" x 14" for RSPF) Copy sizes 3-1/2" x 5-1/2" to 8-1/2" x 14" (Feed copy paper lengthwise only.) Image loss: Max. 5/32" (4 mm) (leading and trailing edges) Max. 11/64" (4.5 mm) (along the other edges in totals) Max.
SPECIFICATIONS AC 120V (±10%), 60 Hz (±2%) Power consumption 1,000 W Overall dimensions 31.9" (W) x 19" (D) (809 mm (W) x 483 mm (D)) Weight (Approximately) 50.7 lbs. (23 kg) Toner cartridge included Copier dimensions 20.
SUPPLIES Types and sizes of copy paper For best results, use only paper recommended by SHARP. Type of paper feeding Type of media Size Weight Paper tray Standard paper Letter (8-1/2" x 11") Legal (8-1/2" x 14") Invoice (5-1/2" x 8-1/2") A4 (210 mm x 297 mm) B5 (182 mm x 257 mm) A5 (148.5 mm x 210 mm) 15 lbs. to 21 lbs. Bypass tray Standard paper and thick paper Letter (8-1/2" x 11") Legal (8-1/2" x 14") Invoice (5-1/2" x 8-1/2") A4 (210 mm x 297 mm) B5 (182 mm x 257 mm) A5 (148.
SUPPLIES Proper storage 1. Store the supplies in a location that is: ● clean and dry, ● at a stable temperature, ● not exposed to direct sunlight. 2. Store copy paper in the wrapper and lying flat. ● Paper stored out of the wrapper or in packages standing on end may curl or get damp, resulting in paper misfeeds.
OPTIONAL EQUIPMENT SYSTEM CONFIGURATION A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following. GDI expansion kit (AR-PG1)* PCL expansion kit (AR-PB9)* * This option is not used for the copier operation. For description of this option, see the separate manual.
250-SHEET PAPER FEED UNIT (AR-DE9) The paper feed unit provide the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying. Part names Side cover Tray Loading copy paper The method of loading copy paper for the paper tray of the paper feed unit is the same as for the paper tray in the copier. See page 10. The method of changing the copy paper size is also the same for the paper tray in the copier. See page 10.
250-SHEET PAPER FEED UNIT (AR-DE9) Close the lower side cover. Close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the ready ( ) indicator will light up. Specifications Copy paper size Paper weight Paper capacity Weight Dimensions Power supply 5-1/2" x 8-1/2" to 8-1/2" x 14" 15 lbs. to 21 lbs. One paper tray with capacity for 250 sheets of 21 lb. bond paper Approx. 6.6 lbs. (3 kg) 19.6" (W) x 15.6" (D) x 3.
INDEX 2 250-sheet paper feed unit . . . . . . . . . . . 41 A Auto clear . . . . . . . . . . . . . . . . . . . . 20, 21 Automatic exposure adjustment . . . . . . . 35 Auto power shut-off mode . . . . . . . . 20, 21 B Bypass tray . . . . . . . . . . . . . . . . . . . . . . 18 C Cautions . . . . . . . . . . . . . . . . . . . . . . . . . 4 Cautions on handling . . . . . . . . . . . . . . . . 9 Charger cleaner . . . . . . . . . . . . . . . . . . . 26 Copier trouble? . . . . . . . . . . . . . . . . . . .
INDEX R Ready indicator . . . . . . . . . . . . . . . . . . . . 7 Reduction . . . . . . . . . . . . . . . . . . . . . . . 17 Replacement – toner cartridge . . . . . . . . . . . . . . . . . . 23 Reversing single pass feeder (RSPF) . . . . . . . . . . . . . . . . . . . . . . . . . 12 S Special paper . . . . . . . . . . . . . . . . . . . . . 38 Specifications – copier . . . . . . . . . . . . . . . . . . . . . . . . 36 – paper . . . . . . . . . . . . . . . . . . . . . . . . . 38 Status indicators . . . . . . .
Date Issued:Nov. 1, 2000 MATERIAL SAFETY DATA SHEET MSDS No. F-01001 Section 1. Product Identification Product: AR-152NT/T/FT/ST (Black Toner) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3. Ingredients Ingredients Styrene-Acrylate copolymer Carbon black Iron oxide Metal Complex dye Section 4.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
Date Issued :Nov. 1, 2000 MATERIAL SAFETY DATA SHEET MSDS No. F-31001 Section 1. Product Identification Product AR-152ND/DV/SD (Black Developer) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3. Ingredients Ingredients Iron powder Styrene-Acrylate copolymer Carbon black Section 4.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
AR-156 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.