Specifications

ManualsBrandsSharp ManualsComputer equipmentAR-PG1

CODE: 00ZAR15OPTA1E

DIGITAL COPIER OPTIONS

AR-SP3 (SPF)

AR-FX3 (FAX)

AR-DE9 (1 TRAY UNIT)

MODEL AR-PG1 (GDI + USB Kit)

∗ For the specifications, operational descriptions, circuit

diagrams, and Parts Guide of the AR-FX3, refer to the AR-F151

Service Manual and Parts Guide.

[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 2 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . 2 - 1

[ 3 ] AR-SP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[ 4 ] AR-DE9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1

[ 5 ] AR-PG1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

● PARTS GUIDE

CONTENTS

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with specified

ones for maintaining the safety and performance of the set.

SHARP CORPORATION

This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

AR-SP3

AR-FX3

AR-DE9

AR-PG1

AR-SP3

Summary of content (47 pages)

PAGE 1
AR-SP3 CODE: 00ZAR15OPTA1E AR-SP3 DIGITAL COPIER OPTIONS AR-FX3 AR-DE9 MODEL AR-SP3 (SPF) AR-FX3 (FAX) AR-DE9 (1 TRAY UNIT) AR-PG1 (GDI + USB Kit) ∗ For the specifications, operational descriptions, circuit diagrams, and Parts Guide of the AR-FX3, refer to the AR-F151 Service Manual and Parts Guide. AR-PG1 CONTENTS [ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1 [ 2 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . 2 - 1 [ 3 ] AR-SP3 . . . . . . . . . . . . . . . . . .
PAGE 2
AR-SP3 Part names [1] GENERAL Side cover 1. List of available options Model AR-150 AR-155 AR-F151 Option AR-SP3 (SPF) ∗1 AR-FX3 (FAX) ∗1 AR-DE9 (1 TRAY UNIT) ∗1 Tray AR-PG1 (GDI + USB Kit) Specifications : Option available : Option not available ∗1: The option setup is provided in the models for Europe. FAX and SPF are incompatible. Copy paper size 5-1/2″ × 8-1/2″ to 8-1/2″ × 14″ Paper weight 15 lbs. to 21 lbs. Paper capacity One paper tray with capacity for 250 sheets of 21 lb.
PAGE 3
AR-SP3 3) Remove the Mylar sheet from the rear cabinet. ● Remove the Mylar sheet that covers the hole for the actuator of sensor unit. [2] UNPACKING AND INSTALLATION 1. AR-SP3 Instalation Manual 4) Remove the hinge guides L and R. ● Remove the screws (two for each) and then remove the hinge guides L and R. 5) Attach the hinge guides L and R.
PAGE 4
AR-SP3 7) Connect the SPF with the copier using the relay harness. <1> Fit the snap band to the position shown in the illustration. <2> Attach the core to the relay harness. At this time, take care on the core position and twist the harness two or three times. <3> Secure the relay harness with the harness clamp. <4> Connect the connector. (Connect the connectors by aligning the black lines.) 10) Attach the sensor unit.
PAGE 5
AR-SP3 2. AR-FX3 Installation Manual 13) Attach the SPF to the copier. ● Attach the SPF by inserting the hinge guide sections of the SP3 into the hinge guides L and R. 1 2 2 Circuit standard label, 1 sheet 14) Insert the power plug into the outlet and turn the main switch of the copier to the “ON” position. 15) Perform SIM setting. ● Execute simulation [2] of [26] and enter [1]. 16) Check the ON/OFF operation of the open detection sensor and book detection sensor.
PAGE 6
AR-SP3 2) Remove the Mylar sheet from the rear cabinet. ● Remove the Mylar sheet that covers the hole for the actuator of sensor unit. 6) Attach the sensor unit. ● While pushing up the sensor unit fully, secure it to the PWB holder with a screw (M3 × 8). M3X8 3) Remove the hinge guides L and R. ● Remove the screws (two for each) and then remove the hinge guides L and R. 7) Replace the line cover.
PAGE 7
AR-SP3 10) Attach the fax PWB. ● While ensuring that the connector of the fax PWB is securely connected to that of the copier, attach the fax PWB to the PWB cover with seven screws (M3 × 6) and connect the relay harness connector. Connect the relay harness to the connector of the fax PWB. (Connect the connectors by aligning the black lines.) 13) Attach the cover to the rear cabinet. <1> Align the arrow marks as shown in the illustration. <2> Then slide the cover to the left.
PAGE 8
AR-SP3 16) Insert the power plug into the outlet and turn the main switch of the copier to the “ON” position. 3) Remove the OP gear cover and rubber feet from the bottom of the copier. ● Remove the screw and remove the OP gear cover. Then, take off and remove the rubber feet. 17) Perform SIM setting. Execute simulation [2] of [26] and enter [1]. 18) Check the ON/OFF operation of the open detection sensor and book detection sensor.
PAGE 9
AR-SP3 6) Attach the rear cover. ● Attach the rear cover to its original position and secure it with the screw (M4 × 12). 9) Remove the paper tray lock for packing. ● Remove the paper tray lock for packing that secures the turning plate in the paper tray by rotating it in the direction of the arrow and store it in the specified position. 10) Set the paper tray side guide. ● Squeeze the lever of the paper tray side guide to slide the guide to the position for the paper size to be used.
PAGE 10
AR-SP3 3) Attach the GDI interface PWB. ● Fit the connector of the GDI PWB into the mounting position of the copier, secure the side A with three screws, and then secure the front B with two screws. 4. AR-PG1 A. Installation Manual A B M3X8 M3X8 4) Attach the GDI harness. ● Attach the GDI harness so that the blue lines face forward and also face toward the GDI interface side. Note: Be careful about the direction of the blue lines.
PAGE 11
AR-SP3 6) Attach the rear cover. ● Align the arrow marks as shown in the illustration and then slide the cover to the left. Then, secure the cover with a screw. (3) Installing the printer driver The software for your printer is provided on CD-ROM. Before installing the printer driver, be sure to check the following items.
PAGE 12
AR-SP3 6) “Install from Disk” window will appear. Insert the installation CDROM into the CD-ROM drive. Type R:\ (if the CD-ROM is designated as drive R) and click the OK button. Proceed to step 7. 4) When using Windows 98 on a personal computer with plug & play*, the “Add New Hardware Wizard” window will appear. Click the Next button and follow the on-screen instructions. ● If the “Add New Hardware Wizard” window does not appear, proceed to step 8.
PAGE 13
AR-SP3 9) The installation program will start. To select a different folder, select Browse and type in the path and folder name where the printer driver will be installed. Click OK and say YES to create the folder, select the Next button to continue. To install the printer driver to the default folder, click the Next button. a. Uninstall AR-150 Series The printer driver can be uninstalled. If the driver is uninstalled, printing can no longer be performed on the printer.
PAGE 14
AR-SP3 [3] AR-SP3 1. Operational descriptions A. Outline The SPF (Single Path Feeder) is installed to the AL-1000/1200 as a standard provision, and it automatically copies up to 30 sheets of documents of a same size. (Only one set of copies) B.
PAGE 15
AR-SP3 D. Cases where a document jam is caused a. b. c. d. When When When When SPPD is ON (document remaining) when the power is turned on. SPPD is not turned ON within about 1.5 sec (at 100% copy) after starting the document feed operation. SPPD is not turned on within about 4.7 sec (at 100% copy) after turning on SPPD. the SPF document jam release door or the OC cover is opened during document transport (SPF motor rotating). 1) Remove the belt, the paper feed frame SP, and two harnesses.
PAGE 16
AR-SP3 A. Sensor PWB C. Clutch 1) Remove two screws from the bottom of the pickup unit. 2) Remove the upper cover. 1) 2) 3) 4) Remove the E-ring. Remove the pulley and bush. Slide the bush in the arrow direction. Lift the clutch, and 5) remove the clutch. 2 2 1 5 1 3 4 1 1) Remove two screws. 2) Remove the sensor PWB. 3) Remove the harness. 1 1 1) Remove the E-ring. 2) Remove the parts. 3 2 1 B. Pickup solenoid 1) Remove two screws. 2) Remove the pickup solenoid 2 D.
PAGE 17
AR-SP3 * When installing the takeup roller, hang the projection of the takeup roller unit on the solenoid arm. 1) Remove the parts. 2) Remove the manual paper feed roller. 3) Remove the pickup roller. 4) Remove the parts. F. SPF motor 1) 2) 3) 4) 5) 6) 4 Remove Remove Remove Remove Remove Remove the harness. four screws. the drive unit. the belt. two screws. the SPF motor. 6 3 1 2 1 5 1 5 2 3 2 4 1 Transport unit removal 1) Remove two screws. 2) Remove the document tray unit.
PAGE 18
AR-SP3 1) 2) 3) 4) H. PS roller 1) Remove the parts. 2) Remove the PS roller. Open the right cabinet. Remove three screws. Remove one connector. While tilting down the 2nd connection arm A, pull and remove the paper feed unit toward you. C D 1 D 2 3 4 1 B I. Paper exit roller A 1 1) Remove the parts. 2) Remove the paper exit roller. 2 1 * * When installing, securely insert two bosses C on the machine side and two bosses D on the paper feed unit side. Be sure to fix the earth B.
PAGE 19
AR-SP3 C. Paper feed solenoid E. Paper feed clutch 1) Remove the screw. 2) Remove the connector. 3) Remove the paper feed solenoid. 1) Remove the E-ring. 2) Remove the paper feed clutch. 3) Remove the parts. 2 3 A 2 1 1 3 D. Transport roller 1) Remove two E-rings. 2) Remove the transport roller. 4 * 1 When installing, fit the cut surface A. F. 2nd paper feed roller 1) Remove the E-ring and the parts. 2) Remove the 2nd paper feed roller.
PAGE 20
AR-SP3 2. Interface 1. Electrical section A. PARALLEL INTERFACE A. GDI/USB PWB This printer uses a bi-directional parallel interface. Use the supplied interface cable. Personal Computer Connector 36-pin DDK 57LE-40360-730B (D29) female connector or equivalent connector Cable Shielded type bi-directional parallel interface For best results,, use a printer interface cable which is IEEE1284 compliant. Pin configuration The pin numbers and signal names are listed in the following table. GND Pin No.
PAGE 21
AR-SP3 B. USB INTERFACE Connector 4-pin DDK DUSB-BRA42-T11 Type-B connector Cable Shielded twisted pair cable (2 m (6 feet) Max.: high-speed transmission equivalent) 2 1 3 4 Pin configuration The pin numbers and signal names are listed in the following table. Pin No. Signal name 1 +5V 2 – DATA 3 +DATA 4 GND 3. Print Area The print area of this printer is shown below. A. 600 dpi B.
PAGE 22
(2-B1) /1284-EN USB-ON /USB-EN 3.3V (2-B3) (2-E3) A 5V1 5V1 2 5 – 3 B 3 5 7 9 12 14 16 18 /STB (2-D3) (2-A2) (2-A2) (2-A3) (2-A2) /USB-EN /AUTOFD /SLCTIN /INIT C614 100p C615 5V1 100p C616 0.1u C621 100p 100p C617 1000p C609 100p (2-A2) (2-A2) C (2-A2) (2-A3) (2-A2) (2-A3) PARAAD2 PARAAD0 (2-A3) PARAAD3 PARAAD1 (2-A3) PARAAD7 PARAAD4 (2-A2) PARAAD5 (2-A2) SLCT PARAAD6 (2-A2) /FAULT 1 DAP202K D607 D608 DAP202K D606 1.
PAGE 23
A USB-IN PDATA11 PCONTROL2 PDATA2 BUSY nAUTOFD PDATA12 5 – 4 24 23 25 20 19 18 17 5 10kJ R511 26 C 0.1u C511 27 5V-USB 3.3V 29 0.1u C520 PDATA16 30 2 VDD5 1 PCONTROL1 IC503A GND 5V2 (2-D3) 31 TC7SH08FU 4 VDD 32 B (1-A4) nINIT 5V2 GND 28 0.
PAGE 24
AR-150P PARTS GUIDE CODE:00ZAR150PT/P1 MODEL AR-SP3 AR-FX3 AR-DE9 AR-PG1 CONTENTS 1 AR-SP3-1(Exterors) 9 AR-SP3(Packing material & Accessories) 2 AR-SP3-2(Pick up unit) F AR-FX3(Packing material & Accessories) 3 AR-SP3-3(Transport unit) G AR-DE9(Packing material & Accessories) 4 AR-FX3-1(Base tray unit) H AR-PG1(Packing material & Accessories) 5 AR-FX3-2(Fax panel pick up unit) I AR-FX3(Fax panel PWB) 6 AR-FX3-3(Fax transport unit) J AR-FX3(Fax PWB) 7 AR-DE9(2nd frame unit) K AR-PG1(GDI/US
PAGE 25
AR-150P DEFINITION The definition of each Rank is as follows and also noted in the list A : Parts necessary to be stocked as High usage parts. B : Parts necessary to be stocked as Standard usage parts. C : Low usage parts. D : Parts necessary for refurbish. E : Unit parts recommended to be stocked for efficient after sales service. Please note that the lead time for the said parts may be longer than normal parts. S : Consumable parts.
PAGE 26
AR-150P 1 AR-SP3-1(Exterors) 11 3 1 15 13 22 2 13 13 22 4 4 5 5 8 501 13 14 5 6 17 7 16 35 17 5 33 18 21 25 28 24 23 34 19 19 36 22 31 27 29 37 26 24 20 31 23 32 20 28 27 22 20 31 30 31 31 FCP03950 –2–
PAGE 27
AR-150P 2 AR-SP3-2(Pick up unit) NO.
PAGE 28
AR-150P 3 AR-SP3-3(Transport unit) NO.
PAGE 29
AR-150P 4 AR-FX3-1(Base tray unit) NO.
PAGE 30
AR-150P 4 AR-FX3-1(Base tray unit) 3 3 6 5 43 44 2 1 9 3 4 29 8 42 3 41 36 12 34 39 13 14 39 37 35 38 15 32 19 16 29 18 19 16 21 22 18 23 24 33 31 20 26 25 31 27 26 29 25 30 28 31 FCP03953 –6–
PAGE 31
AR-150P 5 AR-FX3-2(Fax panel pick up unit) NO.
PAGE 32
AR-150P 5 AR-FX3-2(Fax panel pick up unit) 1 26 2 12 39 3 18 5 16 14 15 13 17 13 6 4 21 19 7 24 20 8 31 25 23 13 22 9 32 18 27 28 30 29 31 10 10 41 10 11 31 40 44 45 40 47 46 37 50 18 42 51 45 48 47 45 18 –8– 49 FCP03954
PAGE 33
AR-150P 6 AR-FX3-3(Fax transport unit) NO.
PAGE 34
AR-150P 7 AR-DE9(2nd frame unit) NO.
PAGE 35
AR-150P 8 AR-DE9(2nd paper feeding unit) NO.
PAGE 36
AR-150P 9 AR-SP3(Packing material & Accessories) NO.
PAGE 37
AR-150P 10 AR-FX3(Packing material & Accessories) NO.
PAGE 38
AR-150P 11 AR-DE9(Packing material & Accessories) NO.
PAGE 39
AR-150P 13 AR-FX3(Fax panel PWB) NO.
PAGE 40
AR-150P 14 AR-FX3(Fax PWB) NO. PARTS CODE 42 V C K Y C Y 1 C B 3 3 3 K PRICE NEW RANK MARK AB 43 V C K Y C Y 1 C F 1 0 4 Z AA VCKYCY1EF104Z VCKYCY1EF104Z VCKYCY1HB103K VCKYCY1HB331K VCKYCY1HF473Z VCQYNU1HM473K VCQYNU1HM332J VCQYNA1HM473K VCQYNU1HM683J VHDDAN202U/-1 VHDDAP202U/-1 VHDDSS133//-1 VHDEK14////-1 VHD1SS355//-1 VHD10E1////-1 VHDRB501V40-1 VHEHZ27-1//-1 VHERD2.7EB2-1 VHERD4.
PAGE 41
AR-150P 14 AR-FX3(Fax PWB) NO.
PAGE 42
AR-150P ■ Index PARTS CODE [C] CBTN-0037QS01 CBTN-0040QS01 CBTN-0041QS01 CCAB-0027QS01 CFRM-0009QS53 " CFRM-0011QS51 " CFRM-0013QS51 " CPWBF0009QS51 CPWBF0009QS52 CPWBF0046QS51 " CPWBX0040QS53 CROLP0015QS01 CSOU-0004QS51 [D] DHAI-0053QSZZ DHAI-0054QSZZ DHAI-0055QSZZ DHAI-0084QSZ1 DHAI-0158QSZZ DHAI-0159QSZ1 DHAI-0160QSZZ DHAI-0161QSZ2 DHAI-0162QSZZ DHAI-0173QSZZ DUNT-0084QS11 " DUNT-0130QSZ1 [G] GCAB-0008QSZZ GCOVA0005QSZZ GCOVA0006QSZZ GCOVA0007QSZZ GCOVA0008QSZZ GLEGG0064FCZZ [J] JBTN-0036QSZZ JBTN-003
PAGE 43
AR-150P PARTS CODE NGERH0193FCZZ " NGERH0972FCZZ " NGERH0990FCZZ " " NGERH0992FCZZ " " NGERH1132FCZZ NGERH1207FCZZ NGERR0377FCZZ " NPLYZ0010QSZZ " NPLYZ0146FCZZ " NROLM0022QSZZ " NROLM0023QSZZ " NROLP0010QSZZ " NROLP0011QSZZ " NROLP0019QSZ1 NROLP0024QSZZ " NROLP1060FCZZ NROLR0922FCZZ " NSFTZ0009QSZZ " NSFTZ0010QSZZ " NSFTZ0011QSZZ " NSFTZ0012QSZZ " [P] PBRSR0003QSZZ " PCOVP0036QSZZ " PCOVP0037QSZZ PCOVP0038QSZZ PCOVP0042QSZZ PCOVP0043QSZZ PCOVP0045QSZZ PCOVP0046QSZZ PCUSS0010QSZ1 " " " PFILW0009QSZZ PGIDH0
PAGE 44
AR-150P PARTS CODE SSAKA0019SCZZ SSAKA2011KCZZ " " SSAKA3442QCZZ " SSAKH0021SCZZ SSAKH3012KCZZ " [T] TCADZ0075QSZZ TCADZ0076QSZZ TCADZ0077QSZZ TCADZ0078QSZZ TINSE0258QSZZ TINSE0305QSZZ TLABH0152QSZZ TTAG-0002QSZZ [U] UBATL2034SCZZ [V] VCCCCY1EH102J VCCCCY1HH101J " VCCCCY1HH150J VCCCCY1HH180J VCCCCY1HH201J VCCCCY1HH220J VCCCCY1HH330J VCCCCY1HH561J VCCCTQ1HH332J VCCCTV1HH330J VCCCTV1HH471J VCEAGA0JW107M VCEAGA1AW226M VCEAGA1CW106M VCEAGA1CW107M VCEAGA1CW226M VCEAGA1CW476M VCEAGU1CW106M VCEAGU1CW476M VCEAJU1C
PAGE 45
AR-150P PARTS CODE VRS-TS2AD680J VRS-TX2HD511J VRSCY1DR5622F VRSCY1JD1542F VRSCY1JD2153F VRSCY1JD2433F VRSCY1JD3740F VRSCY1JD3921F VRSCY1JD4642F VRSCY1JD4872F VRSCY1JD5112F VS2SC3382-/-1 VS2SC3708-/-1 VSDTA143EK/-1 VSP50PB518P// VVLHLM3212-01 [X] XBBSE30P08000 " XBPSD30P05K00 " XBPSD30P06KS0 " XEBSD26P06000 XEBSD30P08000 " " " " " " " " XEBSD30P10000 XEBSD30P12000 " " XEBSD40P10000 " XEBSD40P12000 XEBSE40P12000 " XEBSE40P14000 " XEBSE40P16000 XEPSD30P08X00 " " XHBSD30P06000 XHBSD40P08000 XHBSE30P08000 XPSS
PAGE 46
AR-SP3 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
PAGE 47
AR-SP3 COPYRIGHT © 1999 BY SHARP CORPORATION All rights reserved. Printed in Japan. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.