MODEL AR-M162 AR-M207 DIGITAL MULTIFUNCTIONAL SYSTEM OPERATION MANUAL (for general information and copier) Page PART 1: GENERAL INFORMATION • BEFORE USING THE PRODUCT • TROUBLESHOOTING AND MAINTENANCE • PERIPHERAL DEVICES AND SUPPLIES 12 24 40 PART 2: COPIER OPERATION AR-M162 • COPY FUNCTIONS • CONVENIENT COPY FUNCTIONS • APPENDIX 45 64 73 Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product.
Pegasus-E_Copy_Sec.book 0 ページ 2006年2月15日 水曜日 午後1時33分 Caution: For complete electrical disconnection, pull out the main plug. The socket-outlet should be installed near the equipment and should be easily accessible. FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the machine's serial number located on the back of the unit.
Pegasus-E_Copy_Sec.
Part_1.
CHAPTE~1.FM 3 ページ 2006年4月14日 金曜日 午前9時46分 Notes • Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your nearest SHARP Service Department. • This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest SHARP Service Department.
Pegasus-E_Copy_Sec.book 4 ページ 2006年2月15日 水曜日 午後1時33分 CONTENTS Part 1: General Information PRODUCT CONFIGURATIONS ................................................................................................................ 3 CAUTIONS................................................................................................................................................. 6 ● CAUTIONS ON USING........................................................................................................
Pegasus-E_Copy_Sec.book 5 ページ 2006年2月15日 水曜日 午後1時33分 CONTENTS Part 2: Copier Operation 4 COPY FUNCTIONS NORMAL COPYING ........................................ 45 ● ● ● ● ● 6 APPENDIX SPECIFICATIONS ........................................... 73 MAKING A COPY DARKER OR LIGHTER ....48 SELECTING THE TRAY.................................49 SETTING THE NUMBER OF COPIES ...........49 SELECTING THE ORIGINAL SIZE ................50 USING THE BYPASS TRAY TO COPY A SPECIAL SIZE ORIGINAL.................
Chapter00.fm 6 ページ 2006年4月11日 火曜日 午後12時4分 CAUTIONS Follow the cautions below when using this machine. CAUTIONS ON USING Warning: Fusing unit • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes. Caution: • Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it back on. • Place the machine on a firm, level surface.
Chapter00.fm 7 ページ 2006年4月11日 火曜日 午後12時4分 CAUTIONS LASER INFORMATION Wave length 785 nm +10 nm -15 nm Pulse times North America: (3.1 µs ± 3.1 ns)/7 mm Europe: (3.7 µs ± 3.7 ns)/7 mm Output power Max 0.8 mW At the production line, the output power of the scanner unit is adjusted to 0.8 MILLIWATT PLUS 10 % and is maintained constant by the operation of the Automatic Power Control (APC).
CHAPTE~1.FM 8 ページ 2006年4月13日 木曜日 午後2時11分 INSTALLATION REQUIREMENTS Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved. 1. The machine should be installed near an accessible power outlet for easy connection. 2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.
Chapter00.fm 9 ページ 2006年4月11日 火曜日 午後12時4分 MANUALS PROVIDED WITH THE PRODUCT Multiple manuals are provided for use of the machine. Please read each manual as appropriate for the functions that you wish to use. Operation manual (for general information and copier) (this manual): The first half of this manual contains general information on the machine, including safety precautions and the procedures for loading paper, removing misfeeds, and performing regular maintenance.
Pegasus-E_Copy_Sec.book 10 ページ 2006年2月15日 水曜日 午後1時33分 MAIN FEATURES High-speed laser copying • First-copy time*1 at 300 dpi*2 is only 7.2 seconds. • Copying speed is 20 (AR-M207) or 16 (AR-M162) copies per minute. This provides a big boost to workplace productivity. *1 Measured after the machine has warmed up following power-on, copying using the document glass (8-1/2" x 11" (A4) paper fed from machine tray 1).
Pegasus-E_Copy_Sec.book 11 ページ 2006年2月15日 水曜日 午後1時33分 MAIN FEATURES Fax function (option) Installation of the optional facsimile expansion kit enables the plain-paper, Super G3 laser fax function to be used. Network connection (option) The optional network expansion kit (AR-NB3) can be installed to enable the machine to be used as a network printer and network scanner.
Pegasus-E_Copy_Sec.book 1 12 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT This chapter contains basic information required for use of the machine. Please read this chapter before using the machine. PART NAMES AND FUNCTIONS (5) (15) (10) (11) (9) (1) (6) (2) (7) (3) (7) (8) (4) (17) (14) (1) USB 2.0 port (USB-2) Connect to your computer to this port to use the printer and scanner functions. (2) USB 1.
Pegasus-E_Copy_Sec.book 13 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT (23) (24) (25) (29) (30) (26) 1 (21) (28) (31) (27) (32) (22) (15) Document cover (when installed) Open to make a copy from the document glass. (26) Right side cover (when the SPF is installed) Open to remove misfed originals. (16) Side cover Open to remove misfed paper. (27) Fusing unit release levers To remove the paper misfed in the fusing unit, push down on these levers and remove the paper.
Pegasus-E_Copy_Sec.book 14 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT OPERATION PANEL (1) (2) (3) (4) 26 27 28 29 41 30 42 43 44 45 COPY A 31 B 32 F 36 G 37 K C 33 H 38 L D 34 I 39 M E J 40 N P 46 35 Q 47 U R 48 V W SPEAKER REDIAL/PAUSE O SHIFT S 49 T 50 XYZ SP SPEED COMM. SETTING SYMBOL SPACE/– ON LINE DATA PRINT SCAN LINE DATA FAX (13) (1) Keys for fax function (when the fax option is installed) These are used in fax mode.
Pegasus-E_Copy_Sec.book 15 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT (5) (6) (7) (8) (9) (10) (11) (12) FAX STATUS BACK COPY EXPOSURE PAPER ZOOM OK ABC DEF GHI JKL MNO PQRS TUV WXYZ AUTO % OUTPUT DUPLEX @.
Pegasus-E_Copy_Sec.book 16 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT Display (base screen) Example: Copy mode (1) (2) Icons appearing in the special function icon display (3) (4) Ready to copy. 812 x11 AUTO 100% 812 x11 (5) AUTO (6) (7) * The display shown is the AR-M207 (when the optional RSPF is installed) display. (1) Exposure display Indicates the selected exposure mode. (2) Special function icon display Icons of enabled special functions will appear.
Pegasus-E_Copy_Sec.book 17 ページ 2006年2月15日 水曜日 午後1時33分 TURNING THE POWER ON AND OFF The power switch is located on the left side of the machine. POWER ON POWER OFF Turn the power switch to the "ON" position Make sure that the machine is not in operation and then turn the power switch to the "OFF" position. • It will take about 45 seconds for the machine to warm up. • When the power switch is turned to the "ON" position, the message "System check.
Pegasus-E_Copy_Sec.book 18 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT Default settings The machine is set at the factory to return all settings to the default settings one minute after a copy job is finished (auto clear function) or when the [CA] key is pressed. When the settings return to the default settings, any functions that were selected are canceled. The auto clear time can be changed in the key operator programs. (See the "Key operator's guide".
Pegasus-E_Copy_Sec.book 19 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT Special paper Follow these guidelines when using special paper. • Use SHARP recommended transparency film and label sheets. Using other than SHARP recommended paper may result in misfeeds or smudges on the output. • There are many varieties of special paper available on the market, and some cannot be used with this machine. Before using special paper, contact a SHARP service center.
Pegasus-E_Copy_Sec.book 20 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT Loading paper in the bypass tray 1 Open the bypass tray. Important points when inserting paper in the bypass tray • Up to 100 sheets of standard copy paper can be set in the bypass tray. • Be sure to place 5-1/2" x 8-1/2" (A6 and B6) size paper and envelopes horizontally as shown in the following diagram. Pull out the bypass tray extension to load 8-1/2" x 14" and 11" x 17" (B4 and A3) size paper.
Pegasus-E_Copy_Sec.book 21 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT CHANGING THE PAPER SIZE SETTING OF A TRAY If the size of the loaded paper is different from the size shown in the display, follow the steps below to change the paper size setting of the tray. The paper size setting cannot be changed during copying, printing, fax printing (when the fax option is installed), or interrupt copying, or when a misfeed has occurred.
Pegasus-E_Copy_Sec.book 22 ページ 2006年2月15日 水曜日 午後1時33分 BEFORE USING THE PRODUCT DISABLING (ENABLING) AUTO TRAY SWITCHING When auto tray switching is enabled and paper runs out during copying or printing, the job will continue using paper from a different tray if that tray has the same size of paper in the same orientation. (This function does not operate when using the bypass tray or when a fax is being printed.) This function has been enabled at the factory.
Pegasus-E_Copy_Sec.book 23 ページ 2006年2月15日 水曜日 午後1時33分 AUDITING MODE When auditing mode is enabled, a count is kept of the pages printed by each account. The page counts can be viewed in the display. This function is enabled in the key operator programs. (For the counts in copy, print, and scan modes, see the "Key operator's guide". For the counts in fax mode, see the "Operation manual (for facsimile)" that accompanies the optional facsimile expansion kit.
Pegasus-E_Copy_Sec.book 2 24 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE This chapter explains general troubleshooting and maintenance procedures such as removing misfeeds, replacing the toner cartridge, and cleaning the machine, as well as troubleshooting for the copy function. For troubleshooting for the fax function, printer function, and scanner function, see the respective manuals for each function. TROUBLESHOOTING MACHINE/COPYING PROBLEMS The machine does not operate. ..........
Pegasus-E_Copy_Sec.book 25 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING MACHINE/COPYING PROBLEMS Check the following troubleshooting list before requesting service as many problems can be fixed by the user. If you are unable to solve the problem by checking the list, turn off the power switch, unplug the power cord. Problems related to general use of the machine and copying are described below. If a problem occurs in printer or scanner mode, see the "Operation manual (for printer and scanner)".
Pegasus-E_Copy_Sec.book 26 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution The original was placed in the wrong position. → Place the original correctly. The paper size used for the copy is different from the selected paper size (part of the image is cut off or too much of the page is blank). An appropriate ratio was not used for the size of the original and the size of the paper.
Pegasus-E_Copy_Sec.book 27 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE Problem Cause and solution Was the SPF (or document cover) opened completely when the original was placed on the document glass? → Open the SPF completely and then place the original on the document glass. Close the SPF (or document cover). Page 45 The original is curled or folded. → The original size cannot be correctly detected if the original is curled or folded. Straighten the original.
Pegasus-E_Copy_Sec.book 28 ページ 2006年2月15日 水曜日 午後1時33分 INDICATORS AND DISPLAY MESSAGES If one of the following messages appears in the display, take prompt action as instructed by the message. Message Action (Maintenance icon) It is time for regular maintenance. Contact your SHARP service center. (Developer replacement required icon) Developer is required. Contact your SHARP service center as soon as possible. Maintenance required. Call for service. Maintenance required soon.
Pegasus-E_Copy_Sec.book 29 ページ 2006年2月15日 水曜日 午後1時33分 REMOVING MISFEEDS When a misfeed occurs during copying, the message " Check the location and remove the misfeed. Note Clear paper path." and the location of the misfeed will appear. The paper may tear when you remove a misfeed. In this event, be sure to remove all torn pieces of paper from the machine, taking care not to touch the photoconductive drum (the green part). Any scratches or damage to the surface of the drum will cause dirty copies.
Pegasus-E_Copy_Sec.book 30 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE 2 Open and close the SPF. Opening and closing the cover clears the misfeed display. Copying cannot be resumed until this step is performed. A message may appear indicating the number of originals which must be returned to the document feeder tray. Return the originals to the document feeder tray and press the [START] key ( ). MISFEED IN THE BYPASS TRAY 1 Carefully remove the misfed paper from the bypass tray.
Pegasus-E_Copy_Sec.book 31 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE MISFEED IN THE MACHINE To remove a paper misfeed from the machine, the bypass tray and then the side cover must be opened. Check whether the misfeed occurred in A, B, or C below and then follow the misfeed removal procedure for that location. 1 Open the bypass tray and then the side cover. 2 Determine where the misfeed occurred. Location B If paper is misfed here, go to "Misfeed in B" (page 32).
Pegasus-E_Copy_Sec.book 32 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE Misfeed in B 1 Open the front cover. 4 Lift the fusing unit release levers. 5 Close the front cover and the side cover. Push gently on both ends of the front cover. 2 Turn the roller rotating knob in the direction of the arrow. The message " Clear paper path." will be cleared and copying will be possible.
Pegasus-E_Copy_Sec.book 33 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE Misfeed in C 1 Lower (1) in the illustration, open the fusing unit paper guide, and remove the misfed paper. 3 Close the side cover. The message " Clear paper path." will be cleared and copying will be possible. Be careful not to tear the misfed paper during removal. (1) Warning 2 Note The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or injury.
Pegasus-E_Copy_Sec.book 34 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE MISFEED IN TRAY 2 Note 1 • Make sure that there is no misfed paper in the tray before pulling it out. (Page 31) • Also use the following procedure to remove misfeeds that occur in the 250-sheet paper feed unit and the 2 x 250-sheet paper feed unit. Open the side cover. Grasp the handle to open the side cover. 5 Gently push tray 2 into the machine. Push the tray in completely.
Pegasus-E_Copy_Sec.book 35 ページ 2006年2月15日 水曜日 午後1時33分 REPLACING THE TONER CARTRIDGE When the toner replacement icon ( ) appears, little toner remains. Obtain a replacement cartridge as soon as possible. When the message " Add toner. Can not copy or print." appears in the display, the toner cartridge must be replaced before copying can be resumed. Follow the steps below to replace the toner cartridge.
Pegasus-E_Copy_Sec.book 36 ページ 2006年2月15日 水曜日 午後1時33分 CHECKING THE TOTAL OUTPUT COUNT To check the total number of pages output in copy, print, and fax modes and the total scan count in scanner mode, hold down the [COPY] key when the machine is in the standby state. The counts will appear while the key is held down. The total output count and the total scan count can be used as a guideline for cleaning. When the total output count and the total scan count exceed "999,999", the counts return to "0".
Pegasus-E_Copy_Sec.book 37 ページ 2006年2月15日 水曜日 午後1時33分 CLEANING THE MACHINE CLEANING THE DOCUMENT GLASS AND SPF/DOCUMENT COVER If the document glass, SPF, underside of the document cover, or the scanner for originals coming from SPF (A) (the long narrow glass surface on the right side of the document glass) become dirty, the dirt may appear on copies. Always keep these parts clean. (A) Wipe with a clean, soft cloth. If necessary, moisten the cloth with water or a small amount of neutral detergent.
Pegasus-E_Copy_Sec.book 38 ページ 2006年2月15日 水曜日 午後1時33分 TROUBLESHOOTING AND MAINTENANCE CLEANING THE TRANSFER CHARGER If white or black lines appear in copies or the image is blotchy, the transfer charger may be dirty. Follow the steps below to clean the charger. 1 Turn the power switch off. 5 Place the charger cleaner on the transfer charger and gently slide the cleaner in the direction indicated by the arrow two or three times.
Pegasus-E_Copy_Sec.book 39 ページ 2006年2月15日 水曜日 午後1時33分 ADJUSTING THE DISPLAY CONTRAST The contrast of the display can be adjusted as explained below. 1 Press the [SPECIAL FUNCTION] key. DUPLEX SPECIAL FUNCTION DUPLEX SCAN DUPLEX SCAN ACC. The special function screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 4 Adjust the contrast with the [ ] or [ ] key. To reset the contrast to the default setting, press the [C] key.
Pegasus-E_Copy_Sec.book 3 40 ページ 2006年2月15日 水曜日 午後1時33分 PERIPHERAL DEVICES AND SUPPLIES Optional equipment and supplies are explained in this chapter. To purchase optional equipment and supplies, contact your dealer or SHARP service. OPTIONAL EQUIPMENT Convenient optional equipment can be installed on the machine as needed. Note • As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice.
Pegasus-E_Copy_Sec.book 41 ページ 2006年2月15日 水曜日 午後1時33分 PERIPHERAL DEVICES AND SUPPLIES REVERSING SINGLE PASS FEEDER / SINGLE PASS FEEDER For the names of the parts of the RSPF / SPF, see "PART NAMES AND FUNCTIONS" (page 12). Specifications Model AR-SP6N Acceptable originals AR-RP6N Weight 15 lbs. to 24 lbs.
Pegasus-E_Copy_Sec.book 42 ページ 2006年2月15日 水曜日 午後1時33分 STORAGE OF SUPPLIES Standard supplies for this product that are to be replaced by the user are paper and toner cartridge. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.
Pegasus-E_Copy_Sec.
Pegasus-E_Copy_Sec.
Pegasus-E_Copy_Sec.book 4 45 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS This chapter explains the basic procedures for making copies, including selection of the copy ratio and other copy settings. NORMAL COPYING This section explains how to make a regular copy. If "Auditing mode" has been enabled (page 23), enter your 5-digit account number. Copying from the document glass 1 Open the SPF and place the original face down on the document glass.
Pegasus-E_Copy_Sec.book 46 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS 5 Press the [START] key ( copying. WXYZ ) to begin Note The copy will be delivered to the center tray. @.-_ READ-END • The center tray can hold a maximum of 250 sheets (150 sheets when the job separator tray kit is installed). • About one minute after copying ends, "Auto clear" (page 18) activates and restores the copy settings to the default settings. The setting for "Auto clear" can be changed in the key operator programs.
Pegasus-E_Copy_Sec.book 47 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS Auto paper select mode When auto paper select mode is enabled, "AUTO" appears in the paper size display. This function automatically selects paper that is the same size as the original (5-1/2" x 8-1/2", 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14", 11" x 17", A5, B5, B5R, A4, A4R, B4, A3 paper).
Pegasus-E_Copy_Sec.book 48 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS MAKING A COPY DARKER OR LIGHTER The copy exposure can be adjusted as needed to the original. Three exposure modes are available: "AUTO", "TEXT" and "PHOTO". When "TEXT" or "PHOTO" is selected, the exposure can be manually adjusted to 5 levels. Auto This is the default exposure mode. In this mode, the characteristics of an original being copied are "read" by the exposure system and exposure adjustments are made automatically.
Pegasus-E_Copy_Sec.book 49 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS SELECTING THE TRAY By default the auto paper select function (page 47) operates, and thus the appropriate tray is automatically selected when the original is placed on the document glass or in the document feeder tray, or when the original size is specified.
Pegasus-E_Copy_Sec.book 50 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS SELECTING THE ORIGINAL SIZE If you loaded a non-standard size* original or the original size was not correctly detected, set the original size manually. Perform the following steps after placing the document in the document feeder tray or on the document glass. Note 1 * Standard sizes: The following sizes can be detected correctly: 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2" (A3, B4, A4, A4R, A5).
Pegasus-E_Copy_Sec.book 51 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS USING THE BYPASS TRAY TO COPY A SPECIAL SIZE ORIGINAL When the bypass tray is being used for copying and an original that is placed on the document glass is detected as being a special size, the display will prompt the user to set the original size. To make a copy in this type of situation, follow the steps below. 1 2 POSURE Load paper in the bypass tray and place the original on the document glass. Press the [OK] key.
Pegasus-E_Copy_Sec.book 52 ページ 2006年2月15日 水曜日 午後1時33分 REDUCING OR ENLARGING A COPY There are three ways to enlarge and reduce copies: • Automatic selection of a ratio according to the paper size: Auto ratio selection • Specifying a ratio from 25% to 400%: Preset ratios/zoom • Selecting the vertical and horizontal ratios separately: XY zoom Note When the SPF is being used, the zoom copy ratio range is 50% to 200%.
Pegasus-E_Copy_Sec.book 53 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS 3 Select a preset ratio with the [ ] or [ ] key, or set the ratio (zoom) with the [ ] or [ ] key. GH 4 Press the [OK] key. BACK You will return to the base screen.
Pegasus-E_Copy_Sec.book 54 ページ 2006年2月15日 水曜日 午後1時33分 SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEPARATELY (XY zoom copying) Separate ratio settings can be selected for the length and width of a copy. Example: Reduction only in the horizontal direction Original Copy • This feature cannot be used with the 2 in 1 / 4 in 1 feature or card shot feature. • To use the XY zoom feature and the dual page copy feature simultaneously, set the dual page copy feature first and then the XY zoom feature.
Pegasus-E_Copy_Sec.book 55 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS 7 Press the XY ZOOM 121% ZOOM 100% X: 121% 95% Y: 100% [ ]:X Y @.-_ FUNCTION ACC. #-C 11 key. READ-E Select any other copy settings as needed and press the [START] key ( ). WXYZ @.-_ READ-END The vertical ratio can now be selected. 8 Set the vertical ratio with the [ ], [ ], [ ], or [ ] keys. A preset ratio can be selected with the [ ] or [ ] keys. The ratio can be adjusted in increments of 1% with the [ ] or [ ] keys.
Pegasus-E_Copy_Sec.book 56 ページ 2006年2月15日 水曜日 午後1時33分 TWO-SIDED COPYING TWO-SIDED COPYING The machine is capable of the following types of automatic two-sided copying. The copy paper is turned over automatically, allowing two-sided copying to be accomplished with ease.
Pegasus-E_Copy_Sec.book 57 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS TWO-SIDED COPYING OF ONE-SIDED ORIGINALS • Paper sizes that can be used are 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, A3, B4, A4, A4R, B5, B5R and A5. • Automatic two-sided copying is not possible when the bypass tray is used.
Pegasus-E_Copy_Sec.book 58 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS Copying from the document glass 1 Place the original for the front side of the copy on the document glass, and close the SPF. 6 Make sure that the desired paper tray is selected. 7 Set the number of copies and press the [START] key ( ). WXYZ 2 Press the [DUPLEX] key.
Pegasus-E_Copy_Sec.book 59 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS TWO-SIDED COPIES OF TWO-SIDED ORIGINALS (ONLY WHEN USING THE RSPF) • Paper sizes that can be used are 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, A3, B4, A4, A4R, B5, B5R and A5. • Automatic two-sided copying is not possible when the bypass tray is used. • This copy function cannot be used in combination with dual page copy.
Pegasus-E_Copy_Sec.book 60 ページ 2006年2月15日 水曜日 午後1時33分 COPY FUNCTIONS ONE-SIDED COPIES OF TWO-SIDED ORIGINALS (ONLY WHEN USING THE RSPF) • Paper sizes that can be used are 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, A3, B4, A4, A4R, B5, B5R and A5. • Automatic two-sided copying is not possible when the bypass tray is used. • This copy function cannot be used in combination with dual page copy.
Pegasus-E_Copy_Sec.book 61 ページ 2006年2月15日 水曜日 午後1時33分 TWO-SIDED COPIES USING THE BYPASS TRAY Follow the steps below to perform two-sided copying manually. Example: Copying original A and original B onto both sides of the paper 1 1 2 1 If you are using the AR-M207 The AR-M207 is equipped standard with an automatic two-sided copying function that automatically turns over the paper.
Pegasus-E_Copy_Sec.book 62 ページ 2006年2月15日 水曜日 午後1時33分 DUAL PAGE COPY (Dual page copy) The dual page copy function produces separate copies of open bound original pages. This function is convenient when you wish to make a separate copy of each page of a book or other bound document. Original • • • • 8-1/2" x 11" (A4) paper can be used for dual page copying. When rotation copy is enabled, 8-1/2" x 11"R (A4R) paper can also be used.
Pegasus-E_Copy_Sec.book 63 ページ 2006年2月15日 水曜日 午後1時33分 INTERRUPTING A COPY RUN (Interrupt copying) A copy run can be temporarily interrupted to allow another copy job to be performed. (Interrupt copying) When the other job is finished, the copy run will resume using the original copy settings. • Interrupt copying is not possible when the document glass is being used for a copy job and "NO SORT" is selected. • When 2 in 1 or 4 in 1 is selected, interrupt copying is not possible.
Pegasus-E_Copy_Sec.book 5 64 ページ 2006年2月15日 水曜日 午後1時33分 CONVENIENT COPY FUNCTIONS This chapter explains convenient copy functions. Select convenient copy functions after pressing the [COPY] key to select copy mode.
Pegasus-E_Copy_Sec.book 65 ページ 2006年2月15日 水曜日 午後1時33分 CONVENIENT COPY FUNCTIONS 1 Place the originals in the document feeder tray or the first original on the document glass. If the originals are placed in the document feeder tray, sort mode will be automatically selected. This can be changed to no sort in the key operator programs. (See the "Key operator's guide".) If the first original is placed on the document glass, no sort mode will be automatically selected.
Pegasus-E_Copy_Sec.book 66 ページ 2006年2月15日 水曜日 午後1時33分 COPYING MULTIPLE ORIGINALS ONTO A SINGLE SHEET OF PAPER (2 in 1 / 4 in 1 copy) Multiple originals can be copied onto a single sheet of paper in a selected layout. This function is convenient when you wish to present multiple pages in a compact format, or show a view of all pages in a document. One of two layouts can be selected for 2 in 1 copy, and one of four layouts can be selected for 4 in 1 copy.
Pegasus-E_Copy_Sec.book 67 ページ 2006年2月15日 水曜日 午後1時33分 CONVENIENT COPY FUNCTIONS 5 Select "2in1/4in1" with the [ ] or [ ] key. Select the borderline setting with the [ ] or [ ] key. SPECIAL MODES DUAL PAGE COPY 2in1/4in1 XY ZOOM [OK]:CHANGE GH PQR DUPLEX SPECIAL FUNCTION DUPLEX SCAN 6 10 2in1/4in1 OFF 2in1 4in1 [OK]:CHANGE The 2 in 1 / 4 in 1 selection screen will appear. BORDER Select solid line, broken line, or none. Press the [OK] key. OK 2in1 PATTERN 1 11 Press the [OK] key.
Pegasus-E_Copy_Sec.book 68 ページ 2006年2月15日 水曜日 午後1時33分 CREATING MARGINS WHEN COPYING (Margin shift) The margin shift function shifts the image to create a margin at the edge of the paper. By default the function creates a 1/2" (10 mm) margin at the left edge of the paper. Margin (top) Margin (left edge) A A A A Original Copy Original Copy • You can select whether to create a margin at the top edge or at the left edge of the paper.
Pegasus-E_Copy_Sec.book 69 ページ 2006年2月15日 水曜日 午後1時33分 ERASING SHADOWS AROUND THE (Erase copy) EDGES OF A COPY This feature is used to erase shadows that appear around the edges of copies of books and other thick originals. (Edge erase) The feature can also erase the shadow that appears down the center of books and other originals that open up. (Center erase) Both the shadow lines around the edges of copies and the shadow at the center can be erased.
Pegasus-E_Copy_Sec.book 70 ページ 2006年2月15日 水曜日 午後1時33分 CONVENIENT COPY FUNCTIONS 7 Select the erasure width with the [ ] or [ ] key. If you select 0" (0 mm), the printed result is the same as when "OFF" is selected. 8 Press the [OK] key. OK 9 Select other copy settings as needed and press the [START] key ( ). WXYZ @.-_ READ-END 70 You will return to the base screen. To cancel an edge erase setting, return to the edge erase settings screen and select "OFF".
Pegasus-E_Copy_Sec.book 71 ページ 2006年2月15日 水曜日 午後1時33分 CARD SHOT When copying a card, this function allows you to print the front and back sides of the card next to each other on a single sheet of paper. This function creates 2 in 1 images of the front and back side of the card and centers them on the paper. Original Copy CARD CARD Front of card Back of card CARD Example: Landscape 8-1/2" x 11" size Example: Portrait 8-1/2" x 11" size • Paper cannot be fed from the bypass tray.
Pegasus-E_Copy_Sec.book 72 ページ 2006年2月15日 水曜日 午後1時33分 CONVENIENT COPY FUNCTIONS 8 Press the [START] key ( WXYZ ). The front side of the card is scanned. @.-_ READ-END 9 Turn the original over on the document glass. 10 Press the [START] key ( ). Copying will start after both sides of the original have been scanned.
Pegasus-E_Copy_Sec.book 6 73 ページ 2006年2月15日 水曜日 午後1時33分 APPENDIX SPECIFICATIONS Name Digital Multifunctional System AR-M162 AR-M207 Type Desktop Photoconductive type OPC drum Document glass type Fixed Copy system Laser electrostatic method Originals Sheets, bound documents, max. original size 11" x 17" (A3) Copy sizes Max. 11" x 17" (A3), min. 5-1/2" x 8-1/2" (A5) (5-1/2" x 8-1/2" (A5) can only be fed from tray 1 and the bypass tray) Image loss: Max.
Pegasus-E_Copy_Sec.book 74 ページ 2006年2月15日 水曜日 午後1時33分 APPENDIX Overall dimensions 23-15/64" (W) x 23-7/16" (D) (590 mm (W) x 595 mm (D)) (with bypass tray folded) Weight Approx. 65.5 lbs. (29.
Pegasus-E_Copy_Sec.book 75 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Page : 1/4 Date Revised : Aug.18, 2003 Date Issued : Jun. 1, 2003 MSDS No. F-01211 1.PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-202NT / AR-202T / AR-202ST / AR-202FT / AR-202ST-C / AR-203ST-C / AR-016T/ AR-016ST / AR-016FT / AR-016RT (Black Toner) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below.
Pegasus-E_Copy_Sec.book 76 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Page : 2/4 Date Revised : Aug.18, 2003 Date Issued : Jun. 1, 2003 MSDS No. F-01211 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur.
Pegasus-E_Copy_Sec.book 77 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Page : 3/4 Date Revised : Aug.18, 2003 Date Issued : Jun. 1, 2003 MSDS No. F-01211 Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 3 : 15mg/m (Total Dust), 3 : 10mg/m (Total Dust), 3 5mg/m (Respirable Dust) 3 3mg/m (Respirable Dust) : Not required under intended use.
Pegasus-E_Copy_Sec.book 78 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Chronic Effect Page : 4/4 Date Revised : Aug.18, 2003 Date Issued : Jun. 1, 2003 MSDS No.
Pegasus-E_Copy_Sec.book 79 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Page : 1/4 Date Issued :Jun. 1, 2003 MSDS No. F-31211 1.PRODUCT AND COMPANY IDENTIFICATION Product Name Supplier Identification : AR-202ND / AR-202DV / AR-202SD / AR-202SD-C (Black Developer) : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. Area (Country) (Name and Telephone Number) U.S.A.
Pegasus-E_Copy_Sec.book 80 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Page : 2/4 Date Issued :Jun. 1, 2003 MSDS No. F-31211 3.HAZARDS IDENTIFICATION Most Important Hazards and Effects of the Products Human Health Effects : There are no anticipated carcinogenic effects from exposure based on animal tests performed using toner. When used as intended according to instructions, studies do not indicate any symptoms of fibrosis will occur. Environmental Effects : No data are available.
Pegasus-E_Copy_Sec.book 81 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Page : 3/4 Date Issued :Jun. 1, 2003 MSDS No. F-31211 Exposure Limit Values OSHA-PEL(USA) ACGIH-TLV(USA) Personal Protective Equipment Respiratory Protection Hand Protection Eye Protection Skin Protection Other Protective Equipment 3 : 15mg/m (Total Dust), 3 : 10mg/m (Total Dust), 3 5mg/m (Respirable Dust) 3 3mg/m (Respirable Dust) : Not required under intended use. : Not required under intended use.
Pegasus-E_Copy_Sec.book 82 ページ 2006年2月15日 水曜日 午後1時33分 MATERIAL SAFETY DATA SHEET Chronic Effect Page : 4/4 Date Issued :Jun. 1, 2003 MSDS No.
Pegasus-E_Copy_Sec.book 83 ページ 2006年2月15日 水曜日 午後1時33分 INDEX Symbols / Numbers E [ ] key .....................................................................15 2 in 1 / 4 in 1 copy .....................................................66 250-sheet paper feed unit / 2 x 250-sheet paper feed unit .....41 2-sided printing..........................................................18 Envelopes ................................................................ 20 Erase copy ...................................
Pegasus-E_Copy_Sec.book 84 ページ 2006年2月15日 水曜日 午後1時33分 O T Offset function .....................................................63, 65 [OK] key ....................................................................14 ONLINE indicator ......................................................14 Operation in copy, print, scan, and fax modes..........16 Operation panel...................................................12, 14 Original guides ....................................................
Pegasus-E_Copy_Sec.book 85 ページ 2006年2月15日 水曜日 午後1時33分 INDEX BY PURPOSE Convenient copy functions 2 in 1 / 4 in 1 copy .....................................................66 Card shot...................................................................71 Erase copy ................................................................69 Margin shift................................................................68 Rotation copy ............................................................64 Sort mode...........
Pegasus-E_Copy_Sec.
Pegasus-E_Copy_Sec.
Pegasus-E_Copy_Sec.
Pegasus-E_Copy_Sec.book 89 ページ 2006年2月15日 水曜日 午後1時33分 For users in the USA This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
AR-M162/AR-M207 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163. www.sharpusa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 This manual has been printed using a vegetable-based soy oil ink to help protect the environment.
00-1_Cover1.
00-2_Cover2.fm 1 ページ 2005年11月21日 月曜日 午前9時31分 Warranty While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual. © Copyright SHARP Corporation 2006. All rights reserved.
Pegasus-E_Setup_Eng.book 1 ページ 2005年1月14日 金曜日 午前10時30分 INTRODUCTION Thank you for purchasing this product. This manual explains how to install the printer driver and utilities that are required for the printer and scanner functions. The optional network expansion kit (AR-NB3) enables the machine to be used as a network scanner and network printer. The optional PS3 expansion kit (AR-PK1/N) enables the machine to be used as a PostScript compatible printer.
Chapter00.fm 2 ページ 2005年1月24日 月曜日 午前8時50分 ABOUT THE CD-ROMS This product includes CD-ROMs that are provided standard with the machine and CD-ROMs that are provided with the optional network expansion kit (AR-NB3). For Windows ■ CD-ROM provided standard with the machine There are two CD-ROMs that are provided with the machine.
Chapter00.fm 3 ページ 2005年1月24日 月曜日 午前8時50分 ■ CD-ROMS in the network expansion kit (AR-NB3) The optional network expansion kit includes the following four CD-ROMs: 1. "Software CD-ROM (1)" included in the network expansion kit • PCL5e and PCL6 drivers, and PS driver • Printer Status Monitor • Printer Administration Utility • NICManager • PC-FAX driver • Macintosh PPD File 3.
Chapter00.fm 4 ページ 2005年1月24日 月曜日 午前8時50分 3. "Sharpdesk" CD-ROM Sharpdesk is an integrated software environment that makes it easy to manage document and image files, and launch applications. For information on the "Sharpdesk" CD-ROM and how to install Sharpdesk, see the "Sharpdesk installation guide" that accompanies the network expansion kit. Sharpdesk (Desktop Document Management Software) Sharpdesk is used to manage images scanned from the machine and files created in various software programs.
Pegasus-E_Setup_Eng.book 5 ページ 2005年1月14日 金曜日 午前10時30分 CONTENTS INTRODUCTION ........................................................................................................................................ 1 ● SOFTWARE LICENSE ..................................................................................................................................... 1 ● ABOUT THE CD-ROMS ......................................................................................................................
Chapter00.fm 6 ページ 2005年11月11日 金曜日 午後5時1分 SETUP IN A MACINTOSH ENVIRONMENT HARDWARE AND SOFTWARE REQUIREMENTS ................................................................................ 32 APPLETALK SETTINGS ......................................................................................................................... 32 INSTALLING THE PPD FILE................................................................................................................... 32 ● INSTALLATION IN MAC OS X .
Chapter01.fm 7 ページ 1 2005年11月21日 月曜日 午前9時32分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) BEFORE INSTALLATION HARDWARE AND SOFTWARE REQUIREMENTS Before installing the software, see "HARDWARE AND SOFTWARE REQUIREMENTS" on page 43 to make sure your computer meets the hardware and software requirements. INSTALLATION ENVIRONMENT AND USEABLE SOFTWARE The software that can be installed varies depending on your operating system version and type of connection to the machine.
Pegasus-E_Setup_Eng.book 8 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) INSTALLATION METHOD 1 Use this procedure to install the software in the following environments: 1. The printer is connected by USB cable. 2. Windows version: Windows 98/Windows Me/Windows 2000*/Windows XP* The following procedure uses Windows XP as an example. Follow the same steps to install the software on other operating systems.
Pegasus-E_Setup_Eng.book 9 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) 8 When the "Finish" screen appears, click the [Close] button. When "Now connect the MFP interface cable to the PC." appears, click the [OK] button. Caution Note 9 If you are using Windows 2000/XP If a warning message regarding the Windows logo test or digital signature appears, be sure to click the [Continue Anyway] or [Yes] button.
Pegasus-E_Setup_Eng.book 10 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) INSTALLATION METHOD 2 Use this procedure to install the software in the following environments: 1. The printer is connected by USB cable or parallel cable. 2. Windows version: Windows XP Note To install this software, you must have administrator's rights. Custom installation Installation methods 2 through 4 are for custom installations of the software.
Pegasus-E_Setup_Eng.book 11 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) 10 The files required for installation of the MFP driver are copied (if "MFP Driver" was selected in Step 8). 14 Connect the machine to your computer with the interface cable. (Page 44) • If you are using a USB cable, make sure the machine power is turned on and then connect the cable.
Pegasus-E_Setup_Eng.book 12 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) INSTALLATION METHOD 3 Use this procedure to install the software in the following environments: 1. The printer is connected by USB cable. 2. Windows version: Windows 98/Windows Me/Windows 2000* Note 1 * To install this software, you must have administrator's rights. Make sure that the USB cable is not connected to the machine. If the cable is connected, a Plug and Play window will appear.
Pegasus-E_Setup_Eng.book 13 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) 8 If you wish to install Button Manager, Sharpdesk, or the PC-FAX driver, click the [Utility Software] button in step 5. If you do not wish to install any of the above software components, go to step 10. 9 Click the [Button Manager] button, the [Sharpdesk] button, or the [PC-FAX Driver] button. • To view information on the software, click the [Display Readme] button.
Pegasus-E_Setup_Eng.book 14 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) INSTALLATION METHOD 4 Use this procedure to install the software in the following environments: 1.The printer is connected by parallel cable. 2.Windows version: Windows 95/Windows 98/Windows Me/Windows NT 4.0*/Windows 2000* Note 1 * To install this software, you must have administrator's rights.
Pegasus-E_Setup_Eng.book 15 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) 10 Select the printer port and click the [Next] button. 16 Click the [Sharpdesk] button. • To view information on the software, click the [Display Readme] button. • Follow the on-screen instructions. Select [LPT1] for the printer port. Note Note 11 If [LPT1] does not appear, another printer or peripheral device is using [LPT1].
Pegasus-E_Setup_Eng.book 16 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) USING THE MACHINE AS A SHARED PRINTER VIA A SERVER The machine can be used as a shared printer in a Windows 95/98/Me/NT 4.0/2000/XP network environment. Note that the Windows network environment must already be established. Follow these steps to install the printer driver in the client computer. Ask your network administrator for the server name and printer name of the machine on the network.
Pegasus-E_Setup_Eng.book 17 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) 8 Select the network printer that is shared and click the [OK] button. 1 Note Ask your network administrator for the server name and printer name of the machine on the network. 9 In the printer port selection window, verify the network printer that is shared and click the [Next] button.
Pegasus-E_Setup_Eng.book 18 ページ 2005年1月14日 金曜日 午前10時30分 SETTING UP BUTTON MANAGER Button Manager is a software program that works with the scanner driver to enable scanning from the operation panel of the machine. To scan using the operation panel of the machine, Button Manager must be linked with the destination that appears in the display. Follow the steps below to link Button Manager to machine scanner events.
Pegasus-E_Setup_Eng.book 19 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) WINDOWS 98/ME/2000 1 Click the [Start] button, select [Settings], and then click [Control Panel]. 2 Double-click the [Scanners and Cameras] icon. Note 3 6 Select [Sharp Button Manager G] in "Send to this application". If the [Scanners and Cameras] icon does not appear in Windows Me, click [view all Control Panel options]. 1 Select [SHARP AR-XXXX] and click the [Properties] button.
Pegasus-E_Setup_Eng.book 20 ページ 2005年1月14日 2 金曜日 午前10時30分 INSTALLING THE SOFTWARE (FOR OPTIONS) INSTALLATION FOR A NETWORK CONNECTION The procedures for installing the software when the machine is used as a network printer using the optional network expansion kit (AR-NB3) are explained in this chapter. Refer to the following table for the installation procedure to follow depending on whether you are using a Windows environment (TCP/IP network) or a Macintosh environment.
Pegasus-E_Setup_Eng.book 21 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT HARDWARE AND SOFTWARE REQUIREMENTS Before installing the software, see "HARDWARE AND SOFTWARE REQUIREMENTS" on page 43 to make sure your computer meets the hardware and software requirements. SETTING THE IP ADDRESS OF THE MACHINE Before installing the printer driver, be sure to set the IP address of the machine.
Pegasus-E_Setup_Eng.book 22 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT 7 Click the [Administrator Tools] button. 10 Click the [Print Server Card Setup] button. If the machine is being used in a DHCP environment or the IP address has otherwise already been set, go to step 15. 8 11 If the IP address has not been set (the IP address is set to "0.0.0.0"), a message will appear prompting you to set the IP address. Click the [Yes] button.
Pegasus-E_Setup_Eng.book 23 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT 17 Configure the settings and then click the [Update] button. Be sure to ask your network administrator for the correct IP address, subnet mask, and default gateway to be entered. 18 Your changes to the settings appear. Make sure that the changes are correct and then click the [OK] button. 19 Restart the machine. 2 Power off the machine and then power it back on. 20 Select [Search] from the [File] menu.
Pegasus-E_Setup_Eng.book 24 ページ 2005年1月14日 金曜日 午前10時30分 INSTALLING THE SOFTWARE INSTALLING THE PRINTER DRIVER (STANDARD INSTALLATION) Note Caution If you wish to install the display font or specify the machine's IP address by direct entry when installing the printer driver, select [Custom installation]. (Page 26) To use the machine as a network printer in Windows NT 4.0, "TCP/IP Protocol" must be installed on your computer. If this is not installed, see Windows NT 4.0 Help to install them.
Pegasus-E_Setup_Eng.book 25 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT 9 Printers connected to the network are detected. Select the machine and click the [Next] button. 13 Check the contents of the window and click the [Next] button. Installation of the printer driver begins. Caution If you are using Windows 2000/XP/Server 2003 If a warning message regarding the Windows logo test or digital signature appears, be sure to click the [Continue Anyway] or [Yes] button.
Pegasus-E_Setup_Eng.book 26 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT CUSTOM INSTALLATION If you wish to install the display font or specify the machine's IP address by direct entry when installing the printer driver, select [Custom installation]. 1 Insert the network expansion kit "Software CD-ROM (1)" into your computer's CD-ROM drive. 2 Click the [start] button, click [My Computer] ( ), and then double-click the [CD-ROM] icon ( ). In Windows 95/98/Me/NT 4.
Pegasus-E_Setup_Eng.book 27 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT 11 12 A confirmation window appears. Check the contents and then click the [Next] button. 16 Installation of the printer driver begins. When the printer driver selection window appears, select the printer driver to be installed and click the [Next] button. Select the checkboxes of the printer drivers to be installed. Check the contents of the window and click the [Next] button.
Pegasus-E_Setup_Eng.book 28 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT USING THE MACHINE AS A SHARED PRINTER VIA A SERVER If the printer server in a Windows NT server environment, NetWare server environment, or other environment is configured to share the printer (the machine), follow the steps below to install the printer driver in each client computer. Ask your network administrator for the server name and printer name of the machine on the network.
Pegasus-E_Setup_Eng.book 29 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT 9 Select [Shared Printer] and click the [Next] button. 10 For the port to be used, select the machine (configured as a shared printer), and click the [Next] button. You can also click the [Add Network Port] button and select the printer to be shared (the machine) by browsing the network in the window that appears. 13 Follow the on-screen instructions. Note This completes the installation.
Pegasus-E_Setup_Eng.book 30 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A WINDOWS ENVIRONMENT INSTALLING THE PS DISPLAY FONTS The fonts used by the PS printer driver are contained in the "PRINTER UTILITIES" CD-ROM that accompanied the PS3 expansion kit (AR-PK1/N). Install these fonts as needed for the PS printer driver. 1 Insert the PS3 expansion kit (AR-PK1/N) "PRINTER UTILITIES" CD-ROM into your computer's CD-ROM drive. If your computer is configured for CD-ROM auto start, the installation window appears.
Chapter02.fm 31 ページ 2005年1月24日 月曜日 午前8時51分 USING THE PPD FILE The PPD file enables the machine to print using the standard PS driver of the operating system. Install the PPD file as needed. Use the Add Printer Wizard in Windows to install the PPD file. Be sure to read the Readme file (Readme.txt) before installing the PPD file. The Readme file is in the "EnglishA" or "English" folder. For the location of the folder, see step 4.
Chapter02.fm 32 ページ 2005年11月11日 金曜日 午後5時2分 SETUP IN A MACINTOSH ENVIRONMENT HARDWARE AND SOFTWARE REQUIREMENTS Before installing the PPD file for Macintosh, see "HARDWARE AND SOFTWARE REQUIREMENTS" on page 43 to make sure your computer meets the hardware and software requirements. Operating system Mac OS 8.6 to 9.2.2, 10.1.5, 10.2.8, 10.3.3 to 10.4 CPU and RAM The requirements of the operating system must be satisfied. Note • If Mac OS X v10.1 has not been updated to version 10.1.
Chapter02.fm 33 ページ 2005年11月22日 火曜日 午後1時27分 SETUP IN A MACINTOSH ENVIRONMENT 5 Double-click the [AR-NB3-1] icon ( Note 6 ). 9 Click the [Install] button. Installation of the PPD file begins. • If the "Authenticate" window appears, enter the password and click the [OK] button. • If you are using Mac OS X v10.1.5, click the lock icon ( ), enter the password, and click the [OK] button. Click the [Continue] button. Note 10 7 The License Agreement window will appear.
%JCRVGT HO ࡍࠫ 㧞㧜㧜㧡ᐕ㧝㧞㧝㧞ᣣᦐޓᣣޓඦᓟ㧞ᤨ㧝㧢ಽ SETUP IN A MACINTOSH ENVIRONMENT INSTALLATION IN MAC OS 8.6 TO 9.2.2 1 Insert the network expansion kit "Software CD-ROM (1)" into your computer's CD-ROM drive. 2 Double-click the [CD-ROM] icon ( on the desktop. 3 Double-click the [MacOS] folder. 4 Double-click the [Installer] icon ( The installer window will appear. 5 Click the [Install] button. Note 6 The License Agreement window will appear.
Chapter02.fm 35 ページ 2005年11月11日 金曜日 午後5時2分 CONFIGURING THE PRINTER DRIVER Follow the steps below to configure the machine's printer driver. MAC OS X V10.2 TO 10.4 1 Make sure that the machine is powered on. 2 Select [Applications] from the [Go] menu. 7 Click the machine's model name in the list. 2 3 Double-click the [Utilities] folder. 4 Double-click the [Print Center] icon ( ).
Pegasus-E_Setup_Eng.book 36 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A MACINTOSH ENVIRONMENT 10 Click the [Add] button. The machine is added to the list of printers. 11 Click the name of the machine in the "Printer List" window, and select [Show Info] from the [Printers] menu. The "Printer info" window will appear. 12 Select [Installable Options] from the menu. 13 Set the printer configuration based on the options that have been installed, and then click the [Apply Changes] button.
Pegasus-E_Setup_Eng.book 37 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A MACINTOSH ENVIRONMENT MAC OS X v10.1.5 1 Make sure that the machine is powered on. 2 Select [Applications] from the [Go] menu. 3 Double-click the [Utilities] folder. 4 Double-click the [Print Center] icon ( ). 7 Click the machine's model name in the list. The name of the machine that appears is the name that was entered in the AppleTalk settings when the network settings were configured.
Pegasus-E_Setup_Eng.book 38 ページ 2005年1月14日 金曜日 午前10時30分 SETUP IN A MACINTOSH ENVIRONMENT MAC OS 8.6 TO 9.2.2 1 Select [Chooser] from the Apple Menu. 2 Click the [LaserWriter 8] icon. • The model name of your network-connected machine ([SCxxxxxx]) appears in the "Select a PostScript Printer" list on the right. The name of the machine that appears is the name that was entered in the AppleTalk settings when the network settings were configured.
Pegasus-E_Setup_Eng.book 39 ページ 2005年1月14日 3 金曜日 午前10時30分 TROUBLESHOOTING AND USEFUL INFORMATION TROUBLESHOOTING If the software cannot be installed correctly or if you need to remove the software, check the following items on your computer. Troubleshooting information can also be found in the README files for each of the software programs. To view a README file for a software program, click the [Display Readme] button in the software selection window that appears during installation.
Pegasus-E_Setup_Eng.book 40 ページ 2005年1月14日 金曜日 午前10時30分 TROUBLESHOOTING AND USEFUL INFORMATION MFP driver cannot be installed (Windows 2000/XP) Plug and play screen does not appear (when using a USB cable) If the MFP driver cannot be installed in Windows 2000/XP, follow these steps to check your computer's settings.
Pegasus-E_Setup_Eng.book 41 ページ 2005年1月14日 金曜日 午前10時30分 TROUBLESHOOTING AND USEFUL INFORMATION The MFP driver cannot be correctly installed by Plug and Play (Windows 2000/XP) In Windows 2000/XP, if the MFP driver cannot be correctly installed by Plug and Play (for example, Plug and Play takes place without copying the required files for the MFP driver installation from the installer), follow these steps to remove unneeded devices. To install the MFP driver, see "INSTALLING THE SOFTWARE" (page 7).
Pegasus-E_Setup_Eng.book 42 ページ 2005年1月14日 金曜日 午前10時30分 CONFIGURING THE PRINTER DRIVER (Windows environment) After installing the MFP driver (printer driver) or the printer driver for an option, make sure that the printer driver is set as the default printer and that the number of trays on the machine and the paper size of each tray are configured in the printer driver. 1 Click the [start] button, click [Control Panel], click [Printers and Other Hardware], and then click [Printers and Faxes].
Chapter03.fm 43 ページ 2005年11月11日 金曜日 午後5時3分 CHECKING THE IP ADDRESS There are several settings where the IP address must be entered or checked. To check the IP address of the machine, hold down the status button on the network expansion kit for at least 2 seconds to print out a Printer Setting List. Status button Caution HOW TO RESET THE NETWORK EXPANSION KIT To reset the network expansion kit, power on the machine while holding down the status button on the network expansion kit.
Pegasus-E_Setup_Eng.book 44 ページ 2005年1月14日 金曜日 午前10時30分 CONNECTING TO A COMPUTER Connecting a usb cable Please purchase a USB cable (shielded) that complies with the following standard. The USB interface on the machine complies with the USB 2.0*/1.1 standard. * when the dual function board is installed. USB-2: USB 2.0 port USB-1: USB 1.1 port Note • The machine's USB 2.0 port will transfer data at the speed specified by the USB 2.0 only if the Microsoft USB 2.
Pegasus-E_Setup_Eng.book 45 ページ 2005年1月14日 金曜日 午前10時30分 USING THE PC-FAX TRANSMISSION FUNCTION (when the fax option is installed in the Windows environment) To fax a document using the PC-FAX function, follow the same procedure as when you print the document from an application. First select the installed PC-FAX driver as the "printer" and then begin printing. Image data for fax transmission will be generated and the image will be sent as a fax.
TINSE1538QSZZ_Cover1-4 00-4_Cover3_4.fm 1 ページ 2005年11月21日 月曜日 午前9時32分 00-1_Cover1.fm 0 ページ 2005年11月11日 金曜日 午後5時0分 SOFTWARE SETUP GUIDE SOFTWARE SETUP GUIDE DIGITAL MULTIFUNCTIONAL SYSTEM Page • INTRODUCTION • CONTENTS • INSTALLING THE SOFTWARE (THAT ACCOMPANIES THE MACHINE) 1 5 7 • INSTALLING THE SOFTWARE 20 (FOR OPTIONS) • TROUBLESHOOTING AND USEFUL INFORMATION This manual has been printed using a vegetable-based soy oil ink to help protect the environment.
MODEL AR-M162 AR-M207 DIGITAL MULTIFUNCTIONAL SYSTEM KEY OPERATOR'S GUIDE Page • PURPOSE OF THE KEY OPERATOR PROGRAMS • PROGRAMMING A KEY OPERATOR CODE • KEY OPERATOR PROGRAM LIST • USING THE KEY OPERATOR PROGRAMS CHINA KS1 537QSZZ 1 2 3 4
Pegasus-E_Keyope_Sec.
Pegasus-E_Keyope_Sec.book 1 ページ 2006年2月15日 水曜日 午後2時35分 PURPOSE OF THE KEY OPERATOR PROGRAMS The key operator programs are used by the administrator of the machine to enable or disable functions to suit the needs of your workplace. This manual explains only the key operator programs that are common to all the functions of the machine, (copy, fax, printer and network scanner functions), as well as key operator programs that are specifically for the copy function.
Pegasus-E_Keyope_Sec.book 2 ページ 2006年2月15日 水曜日 午後2時35分 PROGRAMMING A KEY OPERATOR CODE 1 Press the [SPECIAL FUNCTION] key. DUPLEX SPECIAL FUNCTION DUPLEX SCAN DUPLEX SCAN ACC. The special function screen will appear. 2 SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST Select "KEY OPERATOR PRG." with the [ ] or [ ] key. GH PQR DUPLEX SPECIAL FUNCTION DUPLEX SCAN 5 Press the [OK] key. OK KEY OP.
01_Keyope.fm 3 ページ 2006年4月11日 火曜日 午後12時56分 KEY OPERATOR PROGRAM LIST A list of basic programs used for the machine and a list of programs used for the copy function are shown below.
Pegasus-E_Keyope_Sec.book 4 ページ 2006年2月15日 水曜日 午後2時35分 USING THE KEY OPERATOR PROGRAMS 1 Press the [SPECIAL FUNCTION] key. DUPLEX SPECIAL FUNCTION DUPLEX SCAN DUPLEX SCAN ACC. The special function screen will appear. 2 PQR SPECIAL FUNCTION 3 MODE SELECT KEY OP. # CHANGE COPIER PRINTER SCANNER Example: The screen when "COPIER" is selected. GH DUPLEX SCAN 6 SPECIAL FUNCTION PAPER SIZE SET DISPLAY CONTRAST TOTAL COUNT KEY OPERATOR PRG. Press the [OK] key.
Pegasus-E_Keyope_Sec.book 5 ページ 2006年2月15日 水曜日 午後2時35分 ACCOUNT CONTROL TOTAL/ACCOUNT These programs are used to control use of the machine by account. To access one of these programs, select "ACCOUNT CONTROL" in the mode selection screen, select the desired program in the account control screen, and press the [OK] key. AUDITING MODE This program is used to enable auditing mode for copy, print, and scan mode. To enable auditing mode for fax mode, see the "Operation manual (for facsimile)".
Pegasus-E_Keyope_Sec.book 6 ページ 2006年2月15日 水曜日 午後2時35分 Resetting a single account Deleting an account number 1 Select "RESET 1 ACC." with the [ key and then press the [OK] key. 2 Select the desired account with the [ [ ] key. ] 1 Select "DELETE" with the [ ] or [ and then press the [OK] key. ] or 2 If you wish to delete all account numbers, select "DELETE ALL ACC." and press the [OK] key. ] or [ If "---,---" appears for a page limit, a limit has not been set.
Pegasus-E_Keyope_Sec.book 7 ページ 2006年2月15日 水曜日 午後2時35分 ACCOUNT LIMIT This program is used to set limits for the number of pages that can be printed by each account in print mode and copy mode. Select "ACCOUNT LIMIT" and press the [OK] key. The following screen appears. ACCOUNT LIMIT SINGLE ACC. LIMIT ALL ACC. LIMIT Limiting the number of pages used by an account 1 Select "SINGLE ACC. LIMIT" with the [ ] or [ ] key and then press the [OK] key.
01_Keyope.fm 8 ページ 2006年2月21日 火曜日 午後3時39分 Select "WAITING COPY LAMP SETTING" and press the [OK] key. The following screen will appear. COPY LAMP SETTING ON OFF 1 Select "ON" or "OFF" with the [ key. 2 Press the [OK] key. Select "MEM. FOR PRINTER" and press the [OK] key. The following screen will appear. MEM. FOR PRINTER 30% 40% 50% 60% ] or [ ] 1 Select the desired percentage with the [ or [ ] key. 2 Press the [OK] key.
Pegasus-E_Keyope_Sec.book 9 ページ 2006年2月15日 水曜日 午後2時35分 Select "AUTO CLEAR" and press the [OK] key. The following screen will appear. System requirements for USB 2.0 (Hi-Speed mode) AUTO CLEAR The USB port (USB-2) on the machine supports USB 2.0 Hi-Speed mode. The following system is required to use USB 2.0 (Hi-Speed mode): The computer is running Windows XP/2000 and the Microsoft USB 2.0 driver is pre-installed, or the USB 2.
Pegasus-E_Keyope_Sec.book 10 ページ 2006年2月15日 水曜日 午後2時35分 Select "MESSAGE TIME" and press the [OK] key. The following screen will appear. MESSAGE SHORT NORMAL LONG TIME (3 sec.) (6 sec.) (9 sec.) 1 Select the desired display time with the [ ] or [ ] key. 2 Press the [OK] key. KEY TOUCH SOUND This program is used to set the volume of the key touch sound that is heard each time a key is pressed. The initial factory setting is "LOW". Select "KEY TOUCH SOUND" and press the [OK] key.
Pegasus-E_Keyope_Sec.book 11 ページ 2006年2月15日 水曜日 午後2時35分 To enable the setting, select "DISABLE PAPER SIZE SET" and press the [OK] key so that a checkmark appears in the checkbox. Select "AUTO POWER SHUT-OFF TIMER" and press the [OK] key. The following screen will appear. AUTO POWER OFF To disable the setting, select "DISABLE PAPER SIZE SET" once again and press the [OK] key so that the checkmark is cleared from the checkbox. ENERGY SAVE These programs are used to configure energy saving settings.
01_Keyope.fm 12 ページ 2006年2月21日 火曜日 午後3時39分 COPY SETTINGS ERASE ADJUST These programs are used to enable various copy functions. To access one of these programs, select "COPIER" in the mode selection screen, select the desired program in the copy settings screen, and press the [OK] key. This is used to set the default erasure width. The factory default setting is "1/2 inch (10 mm)". EXPOSURE ADJUST This program is used to adjust the exposure level when "AUTO" is used for the exposure mode.
01_Keyope.fm 13 ページ 2006年2月21日 火曜日 午後3時39分 Select "DEFAULT TRAY SET" and press the [OK] key. The following screen will appear. DEFAULT TRAY SET TRAY 1 TRAY 2 TRAY 3 TRAY 4 1 2 Select the tray with the [ ] or [ ROTATION COPY If the orientation of the original does not match that of the paper, the image can be rotated. Rotation copy operates when automatic paper selection or automatic ratio selection operates. The function is initially enabled (factory default setting). Note ] key.
Pegasus-E_Keyope_Sec.book 14 ページ 2006年2月15日 水曜日 午後2時35分 RESOLUTION IN AUTO/TEXT MODE This program is used to set the resolution used when the exposure mode is set to "AUTO" or "TEXT". When "300dpi" is selected, the first copy time is shorter than when "600dpi" is selected. The factory default setting is "300dpi". Select "LIMIT OF COPIES" and press the [OK] key. The following screen will appear. LIMIT OF COPIES 99 copies 999 copies Select "RESOLUTION IN AUTO/TEXT MODE" and press the [OK] key.
Pegasus-E_Keyope_Sec.
Pegasus-E_Keyope_Sec.
Pegasus-E_Keyope_Sec.
AR-M162/AR-M207 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163. www.sharpusa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 This manual has been printed using a vegetable-based soy oil ink to help protect the environment.