MODEL AR-5015 N AR-5120 DIGITAL LASER COPIER OPERATION MANUAL Page • GETTING STARTED • MAKING COPIES • STATUS INDICATORS • GENERAL INFORMATION • OPTIONAL EQUIPMENT AR-5015 N AR-5120 2 13 28 36 55
CAUTIONS Follow the cautions below when using this copier. ● The fusing area is hot. Exercise care in this area when removing misfed paper. ● Do not look directly at the light source. Doing so may damage your eyes. ● Place the copier on a firm, level surface. ● Do not install the copier in a humid or dusty location. ● When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.
CONTENTS Page GETTING STARTED ● ● ● ● ● INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . 4 – Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 – Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 COPIER INSTALLATION . . . . . . . . . . . . . . . .
INTRODUCTION GETTING STARTED This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarise yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. Some models may not be available in some countries. Introduction AR-5120 is equipped with two paper trays while AR-5015 N is equipped with one paper tray.
MAIN FEATURES ● Copying speed is 15 copies/min. (AR-5015 N) or 20 copies/min. (AR-5120), which adapts to business use, allowing improvement of working efficiency. GETTING STARTED High-speed laser copying ● First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on). High-quality digital image ● High-quality copying at 600 dpi is performed. In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.
PART NAMES AND FUNCTIONS GETTING STARTED Overall layout Part names and functions Platen cover Place the original on the original table and close the platen cover before copying starts. Paper tray Holds 250 sheets of copy paper. (AR-5120 is equipped with two paper trays.) Original table Place the document to be copied here. Side cover Open to remove misfeeds and to service the copier. Handles Use to move the copier. Side cover handle Lift and pull to open the side cover.
PART NAMES AND FUNCTIONS GETTING STARTED Part names and functions Toner cartridge lock release lever Use to unlock the toner cartridge. Toner cartridge Contains toner. Photoconductive drum Copy images are formed on the photoconductive drum. Fusing unit release levers Lower to remove misfed paper. The fusing unit is hot. Take care in removing paper. Paper guide Open to remove misfed paper. Roller rotating knob Turn to remove misfed paper. Accessories Operation manual . . . . . . . . . . . . . . . . . .
PART NAMES AND FUNCTIONS Operation panel GETTING STARTED Part names and functions Not used INTERRUPT ( ) key and indicator (p. 25) Interrupts a copy run. Copy quantity display Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are made. Also see items and . ZOOM indicator (p. 17) Lights up when a zoom ratio is set. Copy ratio display ( ) key (p. 17) Press and hold down during standby to display the copy ratio in the copy quantity display.
PART NAMES AND FUNCTIONS GETTING STARTED Zero key Use as part of numeric keys to enter copy quantity. Press during a continuous copy run to display the number of copies completed in the current run. Press and hold during standby to display the total output count. 1st display Press and hold down the key. 2nd display 12,345 sheets output Note: A3 size copies are counted as two copies. CLEAR ( ) key Clears the copy quantity display or terminates a copy run.
COPIER INSTALLATION GETTING STARTED Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
CAUTIONS ON HANDLING GETTING STARTED Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object. Cautions on handling Store spare toner cartridges in a cool dry place without removing from the package before use. If they are exposed to direct sunlight or excessive heat, poor copies may result. Do not touch the photoconductive drum (green portion).
LOADING COPY PAPER GETTING STARTED To save space, this copier has been designed with one (AR-5015 N) or two (AR-5120) adjustable front-loading trays, which are easily opened for paper loading. For best results, use only SHARP recommended paper. (See page 50.) The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the paper tray is not installed or is improperly installed.
LOADING COPY PAPER GETTING STARTED Loading copy paper Changing the copy paper size in the tray Left guide 1 Gently lift and pull out the paper tray until it stops. 2 Push the pressure plate down until it locks in place. 3 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper. 4 Move the left guide to the appropriate slot as marked on the tray. ● A5 copy paper cannot be used in the lower paper tray of AR-5120.
LOADING COPY PAPER GETTING STARTED Loading copy paper 8 To set the selected paper size, press the PAPER SIZE ) key. ENTER ( ● The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light ) key up steadily. All other indicators except the START ( indicator will go out. If copying is being performed, paper size setting cannot be made .
AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 39 for setting the auditing mode. 2 ● As each digit is entered, the dashes in the copy quantity display will disappear. ● After the number is entered, the copy quantity display will change to 0. ● If an unassigned number is entered, “––– ” will appear again in the copy quantity display, indicating that the number was not accepted.
NORMAL COPYING Power on 1 MAKING COPIES 2 Turn the power switch on. ● It will take about 35 seconds for the copier to warm up. However, you can make desired settings and press the START ( ) key during warm-up. Copying will start after warm-up. ● If the copier has been programmed in the auditing mode, the START key ( ) indicator will not light up and “––– ” will appear in the copy quantity display. Enter an assigned 3-digit account number. See page 13.
NORMAL COPYING ● For photographs, select PHOTO ( ) and then adjust with the light ( ) and dark ( ) keys as desired. ● There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously. Set the number of copies using the numeric keys.
REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE ( ) key or manually with the PRESET RATIO selector ( , ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. Automatic MAKING COPIES 1 Place the original on the original table and close the platen cover.
REDUCTION/ENLARGEMENT/ZOOM Manual 2 Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio. ● To select a preset reduction or enlargement copy ratio, press the or key repeatedly until the indicator for the desired copy ratio is lit. Preset reduction ratios are: 86%, 81%, 70%, and 50%. B. Preset enlargement ratios are: 115%, 122%, 141%, and 200%. C. Zoom ratios: Any ratio from 50% to 200% can be set, in 1% increments.
BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. For special purpose papers, the original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies.
BYPASS FEED (special paper) ) key to select the bypass 5 Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper or envelopes. 6 Press the START ( ) key. 19 Bypass feed (special paper) Press the TRAY SELECT ( tray.
TWO-SIDED COPYING Two-sided copies can be made on this copier using the bypass tray. MAKING COPIES 1 Place the first original on the original table and make a copy. ● Two-sided copying 2 3 Replace the first original with the second original and close the platen cover. ● Make sure that the first and second originals are oriented in the same way on the original table.
XY ZOOM Original Copy The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.) Press the XY-ZOOM ( 3 Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the vertical direction.
XY ZOOM MAKING COPIES 5 Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the horizontal direction in a similar manner as for the vertical direction. 6 Press the copy ratio display ( ) key. ● The selected ratio for the horizontal direction will be entered and the display will change to the copy quantity display. ● To verify the copy ratios, press and hold down the copy ratio display ( ) key. The vertical and horizontal ratios will be alternately displayed.
B/W REVERSE Original Copy The B/W REVERSE feature is used to reverse black and white areas. 1 Place the original on the original table and close the platen cover. 2 Press the B/W REVERSE ( 3 Check the copy paper size. 4 Make all other desired copier selections and press the START ( ) key. B/W reverse When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the MANUAL mode. Other exposure modes cannot be selected.
DUAL PAGE COPY Original Copy The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the original table. It is especially useful when copying books and other bound documents. If the AUTO IMAGE feature has been selected, this feature cannot be selected. To use the DUAL PAGE COPY feature with the XY ZOOM feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.
INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. ● ● 2 3 4 When the copier stops, remove the original(s) and set the original(s) for interrupt copying. 5 Press the START ( 6 When all INTERRUPT copies are finished, press the INTERRUPT ( ) key again to cancel the INTERRUPT mode, and remove the original used for interrupt copying. Select the desired available copier functions. Set the number of copies.
AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the optional SPF respectively. To set the level for the optional SPF, place an original in the document feeder tray and make sure that the SPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the SPF indicator does not light up.
TONER SAVE MODE This mode reduces toner consumption by approximately 10% in the automatic and manual exposure modes. Copies will be lighter but still adequate for general use. Selection of this mode does not affect the PHOTO mode. Follow the procedure below for setting the toning level. / / ) key to / ● The MANUAL ( ) indicator will go out and the PHOTO ( indicator will begin to blink. ) ● The exposure indicator marked “5” will light up, indicating that the standard toner mode is active.
TONER CARTRIDGE REPLACEMENT When the toner cartridge replacement required ( ) indicator lights up, replacement of the toner cartridge will be needed soon. Obtain a new cartridge. When the toner cartridge replacement required ( ) indicator blinks, the toner cartridge must be replaced before copying can be resumed. Replace the toner cartridge by following the procedure below. For best copying results, be sure to use only SHARP products. The package of SHARP toner has the Genuine Supplies label.
TONER CARTRIDGE REPLACEMENT 5 Gently insert the toner cartridge along the guides until it locks in place while pushing the lock release lever. If dirt or dust is adhered to the toner cartridge, remove it before installing the cartridge. 7 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. The indicator will go out. When closing the covers, be sure to close the front cover securely and then close the side cover.
MISFEED REMOVAL The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location. If paper is accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. For misfeeds in optional equipment, see its section of the operation manual. First confirm the misfeed location. AR-5015 N AR-5120 ( P. 58) ( P. 58) ( P. 30, 33) ( P. 30, 33) ( P.
MISFEED REMOVAL 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to B. Misfeed in the fusing area . If the misfed paper is seen from this side, proceed to C. Misfeed in the transport area . If paper is misfed here, proceed to A. Misfeed in the paper feed area . Misfeed in the paper feed area 1 Push gently on both sides of the front cover and open it. 2 Carefully remove the misfed paper.
MISFEED REMOVAL Roller rotating knob 2 Turn the roller rotating knob in the direction of the arrow. 3 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. Return the release levers to their operating positions. Fusing unit release lever The fusing unit is hot. Take care in removing paper. ● STATUS INDICATORS ● 4 Do not touch the photoconductive drum (green portion) when removing the misfed paper.
MISFEED REMOVAL 3 Close the side cover by pressing the handle on the cover. ● The misfeed ( ) indicator will go out. Misfeed in the paper tray (upper paper tray in AR-5120) Gently lift and pull out the paper tray and remove the misfed paper. 2 Close the paper tray. 3 Lift slightly on the side cover and slide the cover out until it stops. Close the side cover by pressing the handle on the cover.
MISFEED REMOVAL Misfeed in the lower paper tray (AR-5120 only) STATUS INDICATORS 1 Grasp the handle of the lower side cover and gently open the cover. 2 Remove the misfed paper. 3 If the misfed paper is not seen in step 2, gently lift and pull out the lower paper tray and remove the misfed paper. ● Misfeed removal ● 34 Be careful not to tear the misfed paper during removal. Be careful not to tear the misfed paper during removal. 4 Close the paper tray. 5 Close the lower side cover.
DEVELOPER REQUIRED When the indicator lights up, the developer should be replaced. DEVELOPER REPLACEMENT SHOULD ONLY BE DONE BY AN AUTHORISED SHARP SERVICE TECHNICIAN. Contact your service centre as soon as possible. STATUS INDICATORS MAINTENANCE REQUIRED Developer required/ When the indicator lights up, service by an authorised SHARP service technician is required. Contact your service centre as soon as possible.
USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. List of user programs This copier has the following user programs. Program No. GENERAL INFORMATION User programs Program name Description 1 Auto clear time Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made.
USER PROGRAMS Setting the user programs 1 Press and hold the light ( ) key for more than 5 , , , seconds until all the alarm indicators ( , and ) blink and “– –” appears in the copy quantity display. 2 Enter a program number using the numeric keys. ● The selected program number will blink in the copy quantity display. ● If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. ● The program numbers are shown in the table below. ) key.
USER PROGRAMS 4 Select the desired parameter using the numeric keys. ● The entered parameter number will blink on the right side of the copy quantity display. ● The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min., press key 2. Program name ● Parameters Auto clear time 0 5 OFF 10 sec. 1 30 sec. *2 60 sec. 3 90 sec. 4 120 sec. Preheat mode 0 OFF 1 30 sec. 2 60 sec. *3 90 sec. 4 120 sec. 2 60 min.
USER PROGRAMS Settings for auditing accounts Settings of user programs No. 10 to 15 varies with the program number. For setting of all programs, first follow steps 1 to 3 in “Setting the user programs” on page 37 to select a program. (1. Press the light ( ) key for more than 5 seconds. 2. Enter a program number (10 to 15) using the numeric keys. 3. Press the START ( ) key.) Then follow the appropriate instructions for the program. Program No.
USER PROGRAMS Program No. 12: Account number change Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “12E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37. 1. Use the copy ratio display ( number to be changed. ● 2. Use the key to advance through the account numbers.
USER PROGRAMS Program No. 14: Number of copies per account Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “14E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37. 1. Use the copy ratio display ( number. ● 2.
USER PROGRAMS Program No. 15: Resetting account Program No. 15 is used to reset all accounts or to reset any desired individual account. When program No. 15 is entered, “0” will blink on the right side of the copy quantity display. ● If no account number has been registered, “15E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37. 1. To reset an individual account, press the 0 key. To reset all accounts, press key 1. 2. Press the START ( 3.
POWER SAVE MODES The copier has two power save modes to reduce overall power consumption thereby reduce the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode. ● User programs The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. for preheat mode and 30 min. for auto power shut-off mode.
POWER SAVE MODES Setting the power save modes The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 37. ● The copier will enter the preheat mode first and then the auto power shut-off mode after a preset time has elapsed when no copier operation has been made.
USER MAINTENANCE Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Original table and platen cover Stains or dirt on the original table or platen cover will also be copied. Wipe the original table and platen cover with a soft, clean cloth. ● If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. ● If an optional SPF is installed, wipe the scanning window on the original table.
USER MAINTENANCE Transfer charger cleaning If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. Charger cleaner GENERAL INFORMATION 3 Gently lift and pull out the paper tray (upper paper tray in AR-5120) and take the charger cleaner out by holding the tab. 4 Set the charger cleaner onto the transfer charger and gently slide the cleaner in the direction indicated by the arrow two or three times.
COPIER TROUBLE? Problem Solution ● Copier plugged in? Plug the copier into a grounded outlet. See page 8. ● Power switch ON? Turn the power switch ON. See page 14. Copies are too dark or too light. ● Copy density properly adjusted? See pages 14 and 26. Blank copies ● Is the original placed face down? Place the original face down on the original table. ● Paper too heavy? Use copy paper within the specified range. See page 50. ● Paper damp? Replace with dry copy paper.
COPIER TROUBLE? Problem Copies are smudged or dirty. Paper size for a paper tray cannot be set. Power is on but copying is not possible. GENERAL INFORMATION Copier trouble? 48 Solution ● Original table or platen cover dirty? Clean regularly. See page 45. ● Original smudged or blotchy? Use a clean original. ● Is the indicator on? Developer is required. Contact your SHARP service centre as soon as possible. See page 35. ● Is the indicator on? Maintenance is required.
COPIER TROUBLE? Problem Solution ● Is blinking in the copy quantity display? A toner cartridge is not installed. Install a toner cartridge. If "CH" is blinking even if a cartridge is installed properly, contact your SHARP service centre immediately. ● Is steadily lit in the copy quantity display? The side cover is open. Close the front and side covers securely. ● Is the indicator blinking? The toner cartridge must be replaced. See page 28, TONER CARTRIDGE REPLACEMENT.
SUPPLIES Types and sizes of copy paper Size Weight Capacity (80 g/m2 paper) Paper tray A5* to A3 56 to 80 g/m2 250 sheets Bypass tray Ordinary paper: A6 to A3 Envelopes: International DL (110 x 220 mm) International C5 (162 x 229 mm) Commercial 10 (4-1/8" x 9-1/2") 56 to 128 g/m2** (Ordinary paper) 100 sheets * A5 copy paper cannot be used in the lower paper tray of AR-5120. ** For paper weighing from 105 to 128 g/m2, A4 is the maximum size that can be fed through the bypass tray.
SUPPLIES Genuine supplies statement Standard supplies for this copier that are to be replaced by the user are copy paper and toner cartridge. For best copying results, be sure to use only SHARP products. Only genuine SHARP consumables carry the Genuine Supplies label. GENUINE SUPPLIES Proper storage 1. ● clean and dry, ● at a stable temperature, ● not exposed to direct sunlight. Store copy paper in the wrapper and lying flat.
SPECIFICATIONS GENERAL INFORMATION Specifications 52 Type Digital laser copier, desktop Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. A3 Copy sizes Max. A3 Min. A6 Image loss: Max. 4 mm (leading and trailing edges) Max. 4 mm (along other edges in total) Copying speed (at 100% copy ratio) AR-5015 N: 15 copies/min. (A4) 12 copies/min. (A4R) 10 copies/min. (B4) 9 copies/min. (A3) Continuous copy Max.
SPECIFICATIONS Overall dimensions (with bypass tray folded) 590 mm (W) x 531 mm (D) Weight AR-5015 N: Approx. 32 kg AR-5120: Approx. 36.5 kg Toner cartridge included Copier dimensions AR-5015 N: 590 mm (W) x 531 mm (D) x 470 mm (H) AR-5120: 590 mm (W) x 531 mm (D) x 552 mm (H) Operating conditions Temperature: 15°C to 30°C Humidity: 20% to 85% Acoustic noise emission (measurement according to ISO 7779) Sound power level LWA Operating: 6.1 [B], Standby: 3.
MEMO GENERAL INFORMATION 54
OPTIONAL EQUIPMENT CONTENTS ● Page SINGLE PASS FEEDER (AR-SP2) . . . . . . . . . . . . . . . . . . . . . . 56 ● Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ● Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 ● Using the SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 ● Misfeed removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SINGLE PASS FEEDER (AR-SP2) The single pass feeder (SPF) holds up to 30 originals for automatic feeding.
SINGLE PASS FEEDER (AR-SP2) Using the SPF ● ● ● Be sure to remove any staples or paper clips from the originals. Damaged or crumpled originals may misfeed in the SPF. It is recommended that these originals be copied from the original table. Before placing curled or wavy originals into the document feeder tray, be sure to flatten them. If not, original misfeeds may result.
SINGLE PASS FEEDER (AR-SP2) Misfeed removal If an original misfeed occurs in the SPF, the copier will stop and the red indicator which indicates an original misfeed will blink. A B C Location A Feeding roller cover 1 Open the feeding roller cover and pull the original gently to the left and out from the document feeder tray. Close the feeding roller cover. 2 If the misfed original cannot be removed in step 1, open the right side cover and remove the misfed original. Close the right side cover.
INDEX A Auto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 36 Automatic exposure adjustment . . . . . . . . . . . . . . . . . . 26 Auto power shut-off mode . . . . . . . . . . . . . . . . . . . . . . 43 B B/W reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 C Cautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Copier trouble? . . . . . . . . . .
INDEX S Special paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications – copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Storage of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MEMO 61
CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CLASS 1 LASER PRODUCT LASER KLASSE 1 Laserstrahl LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. CAUTION INVISIBLE UNNGÅ EKSPONERING FOR STRÅLEN. ADVERSEL USYNLIG AVOID EXPOSURE TO BEAM. OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND VORSICHT UNSICHTBARE SICHERHEITSVERRIEGELUNG ÜBERERÜCKT.
In some areas, the “POWER” switch positions are marked “ I ” and “ ” on the copier instead of “ON” and “OFF”. If your copier is so marked, please read “ I ” for “ON” and “ ” for “OFF”. Caution! For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible. Warning This is a Class A product.
AR-5015 N/AR-5120 SHARP CORPORATION Printed on 100% post-consumer recycled paper PRINTED IN CHINA 2002L KS TINSE0806QSZZ
