HINA KS➀ QSZZ AL-1633_1644_EX.
AL-1633_1644_EX.book 1 ページ 2003年10月23日 木曜日 午後8時21分 Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from copying by national law. Other items may be prohibited by local law. ● Money ● Stamps ● Bonds ● Stocks ● Checks ● Passports ● Driver's licenses ● Bank drafts In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF".
AL-1633_1644_EX.book 1 ページ 2003年10月23日 木曜日 午後8時21分 CONTENTS CAUTIONS................................................................................................................................................. 3 ● ● ● ● ● CAUTIONS ON USING..................................................................................................................................... 3 IMPORTANT POINTS WHEN SELECTING AN INSTALLATION SITE ...........................................................
AL-1633_1644_EX.book 2 ページ 5 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING 8 APPENDIX TROUBLESHOOTING ..................................... 45 SPECIFICATIONS ........................................... 70 ● MACHINE/COPYING PROBLEMS.................46 ● PRINTING AND SCANNING PROBLEMS .....49 SOFTWARE LICENSE .................................... 73 INDICATORS AND DISPLAY MESSAGES .... 53 MISFEED REMOVAL....................................... 54 ● MISFEED IN THE SPF (only on the SPF model) ..............
AL-1633_1644_EX.book 3 ページ 2003年10月23日 木曜日 午後8時21分 CAUTIONS Follow the cautions below when using this machine. CAUTIONS ON USING Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes. Caution: • Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it back on. • Machine power must be turned off before installing any supplies.
AL-1633_1644_EX.book 4 ページ 2003年10月23日 木曜日 午後8時21分 The machine should be installed near an accessible power outlet for easy connection and disconnection. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. Note Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.
AL-1633_1644_EX.book 5 ページ 2003年10月23日 木曜日 午後8時21分 ENVIRONMENTAL INFORMATION As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. USING THE MANUAL This machine has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all machine features, be sure to familiarise yourself with this manual and the machine.
AL-1633_1644_EX.book 6 ページ 2003年10月23日 木曜日 午後8時21分 CONVENTIONS USED IN THIS MANUAL Warning Warns the user that injury may result if the contents of the warning are not properly followed. Caution Cautions the user that damage to the machine or one of its components may result if the contents of the caution are not properly followed. Notes provide information relevant to the machine regarding specifications, functions, performance, operation and such, that may be useful to the user.
AL-1633_1644_EX.book 7 ページ 2003年10月23日 木曜日 午後8時21分 MAIN FEATURES High-speed laser copying • First-copy time*1 at 300 dpi*2 is only 7.2 seconds . • Copying speed is 16 copies per minute. This is ideal for business use and provides a big boost to workplace productivity. *1 First-Copy time may vary depending on the power-supply voltage, ambient temperature, and other operating conditions. *2 "dpi" ("dots per inch") is unit that is used to measure resolution.
AL-1633_1644_EX.book 8 ページ 2003年10月23日 木曜日 午後8時21分 Chapter 1 1 BEFORE USING THE MACHINE This chapter contains basic information that should be read before using the machine. PART NAMES AND FUNCTIONS 1 1 15 2 16 3 6 5 3 9 4 7 10 14 8 1 2 3 4 5 6 7 8 Document feeder cover (only on the SPF model) /document cover (only on the document cover model) Open to make copies from the document glass. (p.21) Document glass Place an original that you wish to copy/scan face down here. (p.
AL-1633_1644_EX.book 9 ページ 2003年10月23日 木曜日 午後8時21分 BEFORE USING THE MACHINE 24 17 18 23 19 22 20 21 1 28 27 25 29 26 17 to 21 are only on the SPF model. 16 17 18 19 20 21 22 23 24 Parallel port Connect to your computer to use the printer function. (Software Setup Guide) Document feeder tray Place the original(s) that you wish to copy/scan face up here. Holds up to 40 originals. Original guides Adjust to the size of the originals.
AL-1633_1644_EX.book 10 ページ 2003年10月23日 木曜日 午後8時21分 BEFORE USING THE MACHINE OPERATION PANEL 1 1 2 2 3 4 5 3 4 5 6 AL-1633 23 1 2 3 4 5 6 7 8 SCAN MENU key Use to scan by means of the provided Button Manager software. (p.34) SCAN key ( ) / indicator Press to switch the machine to scanner mode and scan by means of the provided Button Manager software.(p.33) The indicator blinks during scanning and transmission of the scanned data.
AL-1633_1644_EX.book 11 ページ 2003年10月23日 木曜日 午後8時21分 BEFORE USING THE MACHINE 6 8 (Two-tray model only) 9 10 11 7 ACC.#-C AUTO A3 A4 A4 A5 B4 EXTRA 17 18 19 20 21 22 23 24 25 26 17 14 15 ZOOM 25 400% INTERRUPT 1 AUTO % ENTER 16 13 200% 141 122 115 100% 86 81 70 50% AUTO 1 3 5 12 18 19 20 21 22 ORIGINAL SIZE ENTER key ( ENTER ) / ORIGINAL SIZE indicators Use to enter the original size. (p.19) The selected original size will light up.
AL-1633_1644_EX.book 12 ページ 2003年10月23日 木曜日 午後8時21分 CHECKING PACKED COMPONENTS AND ACCESSORIES Open the carton and check to ensure that the following components and accessories are included. Operation manual and software CD-ROM Power cord TD cartridge Drum cartridge (installed in machine) Machine Note • If anything is not included or is damaged, contact your authorised service representative. • Save the carton and packing materials.
AL-1633_1644_EX.book 13 ページ 2003年10月23日 木曜日 午後8時21分 SET-UP 1 Remove all pieces of tape, then open the SPF or the document cover and remove the protective material. 2 Use a coin (or other suitable object) to remove the screw. Note 3 5 Store the pressure plate lock which has been removed in step 5 and the screw which has been removed in step 2 in the front of the paper tray. Pressure plate lock To store the pressure plate lock, rotate the lock to fix it on the relevant location.
AL-1633_1644_EX.book 14 ページ 2003年10月23日 木曜日 午後8時21分 INSTALLING THE TD CARTRIDGE 1 Push gently on both ends of the front cover and open it. 4 Insert the TD cartridge along the guides until it locks in place. If there is any dirt or dust on the TD cartridge, remove it before installing the cartridge. 2 Remove the new TD cartridge from the bag. Hold the cartridge on both sides and shake it horizontally four or five times. 5 Close the front cover.
AL-1633_1644_EX.book 15 ページ 2003年10月23日 木曜日 午後8時21分 POWER ON AND OFF The power switch is located on the left side of the machine. POWER ON POWER OFF Turn the power switch to the "ON" position Make sure that the machine is not in operation and then turn the power switch to the "OFF" position. It will take about 45 seconds for the machine to warm up. While the machine is warming up, the POWER SAVE indicator ( ) will blink. (The POWER SAVE indicator ( ) will go off when the machine is ready to copy.
AL-1633_1644_EX.book 16 ページ 2003年10月23日 木曜日 午後8時21分 LOADING PAPER The paper required indicator ( ) will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed. PAPER For best results, use only SHARP recommended paper.
AL-1633_1644_EX.book 17 ページ 2003年10月23日 木曜日 午後8時21分 BEFORE USING THE MACHINE LOADING PAPER Make sure that the machine is not copying or printing, and then follow these steps to load paper. Loading the paper tray 1 Gently lift and pull out the paper tray until it stops. 5 Gently push the paper tray into the machine. 1 2 Push the pressure plate down until it locks in place. Push the centre of the pressure plate down until it locks into place.
AL-1633_1644_EX.book 18 ページ 2003年10月23日 木曜日 午後8時21分 BEFORE USING THE MACHINE Loading the bypass tray 1 3 Unfold the bypass tray. Insert the paper (print face down) all the way into the bypass tray. To prevent a misfeed, verify once more that the paper guides are adjusted to the width of the paper. When feeding large paper such as B4 and A3, pull out the bypass tray extension. 2 Note If you loaded paper in the bypass tray, press the [TRAY SELECT] key ( ) to select the bypass tray.
AL-1633_1644_EX.book 19 ページ 2003年10月23日 木曜日 午後8時21分 BEFORE USING THE MACHINE Envelopes Do not use the following envelopes, as misfeeds will occur. • Envelopes with metal tabs, clasps, strings, holes, or windows. • Envelopes with rough fibres, carbon paper, or glossy surfaces. • Envelopes with two or more flaps. • Envelopes with tape, film, or paper attached to the flap. • Envelopes with a fold in the flap. • Envelopes with glue on the flap to be moistened for sealing. • Envelopes with labels or stamps.
AL-1633_1644_EX.book 20 ページ 2003年10月23日 木曜日 午後8時21分 BEFORE USING THE MACHINE 4 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper, and move the left guide to the appropriate slot as marked on the tray. Left guide Front guide • The front guide is a slide-type guide. Grasp the locking knob on the guide and slide the guide to the indicator line of the paper to be loaded. • The left guide is an insert-type guide.
AL-1633_1644_EX.book 21 ページ 2 2003年10月23日 木曜日 午後8時21分 Chapter 2 COPY FUNCTIONS This chapter explains basic copying functions such as normal copying, reduction or enlargement, and exposure adjustment. NORMAL COPYING This section explains how to make a regular copy. If "Auditing mode" has been enabled (p.43), enter your 3-digit account number. Copying from the document glass 1 Open the document cover/SPF, and place the original.
AL-1633_1644_EX.book 22 ページ 2003年10月23日 木曜日 午後8時21分 COPY FUNCTIONS Copying from the SPF (only on the SPF model) 1 2 Make sure that an original has not been left on the document glass. Close the SPF. 5 Press the [START] key ( copying. The copy is delivered to the paper output tray. Adjust the original guides to the size of the original(s). Note 3 Set the original(s) face up in the document feeder tray. ● Insert the original into the document feeder tray as far as it will go.
AL-1633_1644_EX.book 23 ページ 2003年10月23日 木曜日 午後8時21分 COPY FUNCTIONS Auto paper select mode (Two-tray model only) When the AUTO PAPER SELECT indicator ( AUTO ) lights up, "Auto paper select mode" is enabled. This function automatically selects the paper that is the same size as the original A5, A4, A4R, B4, A3 paper. "Auto paper select mode" can be disabled in the user programs. (p.38) • The sizes of paper that can be loaded vary by country and region.
AL-1633_1644_EX.book 24 ページ 2003年10月23日 木曜日 午後8時21分 COPY FUNCTIONS MAKING A COPY DARKER OR LIGHTER Automatic exposure adjustment is initially enabled. This function automatically adjusts the copy image according to the original being copied. If you wish to select the exposure level yourself, follow the steps below. (Select from two original types and five exposure levels for each original type.) The exposure level used in automatic exposure adjustment can also be changed.
AL-1633_1644_EX.book 25 ページ 2003年10月23日 木曜日 午後8時21分 COPY FUNCTIONS SETTING THE NUMBER OF COPIES Press the numeric keys to set the number of copies. Important note when making a large number of copies ● The set number of copies appears in the display. A maximum of 999 copies (factory default setting) can be set. ● If you wish to make only a single copy, copying is possible with the display showing "0". Note The maximum number of copies can be changed in the user programs. (p.
AL-1633_1644_EX.book 26 ページ 2003年10月23日 木曜日 午後8時21分 COPY FUNCTIONS 4 Press the [AUTO IMAGE] key ( AUTO % ). The AUTO IMAGE indicator ( AUTO % ) lights up and the appropriate ratio for the original size and paper size is selected. (The indicator of the selected ratio will light up.) AUTO % Note 5 Set the number of copies and other copy settings, and then press the [START] key ( ). The copy will be delivered to the paper output tray.
AL-1633_1644_EX.book 27 ページ 2003年10月23日 木曜日 午後8時21分 COPY FUNCTIONS SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEPARATELY (XY ZOOM copying) The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. Example: Reduction only in the horizontal direction. Original Note Copy • To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature.
AL-1633_1644_EX.book 28 ページ 2003年10月23日 木曜日 午後8時21分 COPY FUNCTIONS 6 Use the [PRESET RATIO] selector keys ( , ) and [Zoom] keys ( , to change the copy ratio in the horizontal direction. ) Press the [PRESET RATIO] selector keys ( , ) to select a ratio close to the desired ratio, and then press the [Zoom] keys ( , ) to adjust the ratio in increments of 1%. The ratio appears in the display. 7 Press the [Copy ratio display] key ( ).
AL-1633_1644_EX.book 29 ページ 2003年10月23日 木曜日 午後8時21分 TWO-SIDED COPYING USING THE BYPASS TRAY To perform manual two-sided copying, follow these steps. Example: Copying originals A and B onto each side of one sheet of paper 1 2 1 Copy Original A Original B 1 3 Copy original A. Turn the copy of original A over, and without changing the position of the edge closest to you, insert it in the bypass tray. Insert the paper all the way in.
AL-1633_1644_EX.book 30 ページ 2003年10月23日 木曜日 午後8時21分 DUAL PAGE COPYING A dual page original can be automatically separated into two pages during copying. This feature is convenient for making copies of books and other dual page originals on individual sheets of paper. Original Note 1 • • • • • Copy A4 paper is used for dual page copying. When used in combination with XY ZOOM copying, enlargement is not possible. Dual page copying cannot be used in combination with the enlargement copying.
AL-1633_1644_EX.book 31 ページ 2003年10月23日 木曜日 午後8時21分 INTERRUPTING A COPY RUN (Interrupt copying) A copy run can be temporarily interrupted to allow another copy job to be performed. When the other job is finished, the copy run will resume using the original copy settings. Note 1 Interrupt copying is not possible when the user programs are being configured, or scanning is being performed. Press the [INTERRUPT] key ( interrupt the copy run.
AL-1633_1644_EX.book 32 ページ 3 2003年10月23日 木曜日 午後8時21分 Chapter 3 PRINTER/SCANNER FUNCTIONS The machine includes a USB 1.1 port and a parallel port as standard equipment. A computer can be connected to these ports to use the machine as a printer or a scanner. To use the machine as a printer or scanner, the printer driver or scanner driver must first be installed as explained in the "Software Setup Guide". Note • If a problem occurs in printer or scanner mode, see "TROUBLESHOOTING" (p.45).
AL-1633_1644_EX.book 33 ページ 2003年10月23日 木曜日 午後8時21分 PRINTER/SCANNER FUNCTIONS Pausing a print job To pause a print job during printing, press the [ON LINE] key ( ) on the operation panel to switch the machine off-line. Printing will be paused and the ON LINE indicator ( ) will blink. To cancel a print job, press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). To resume printing, press the [ON LINE] key ( ) to switch the machine online.
!Chapter3.fm 34 ページ 2004年2月5日 木曜日 午前10時45分 PRINTER/SCANNER FUNCTIONS 3 Press a [SCAN MENU] key to begin scanning. 1 Note 2 The display will show the number of the [SCAN MENU] key that you pressed, and the number will light and the SCAN indicator will be blinking. • To return to copy mode from scanner mode, press the [SCAN] key ( ) or [CLEAR ALL] key ( ).
AL-1633_1644_EX.book 35 ページ 2003年10月23日 木曜日 午後8時21分 OPERATION IN COPY, PRINTER, AND SCANNER MODES Some operations cannot be performed simultaneously when the machine is being used in printer mode, copy mode, or scanner mode.
AL-1633_1644_EX.book 36 ページ 4 2003年10月23日 木曜日 午後8時21分 Chapter 4 USER SETTINGS This chapter explains how to set the automatic exposure level, toner save mode, and the user programs, which are custom settings that control fine points of the machine’s operation. ADJUSTING THE AUTOMATIC EXPOSURE LEVEL The exposure level used in automatic exposure adjustment, which automatically adjusts the copy exposure according to the original, can be adjusted.
AL-1633_1644_EX.book 37 ページ 2003年10月23日 木曜日 午後8時21分 ENABLING TONER SAVE MODE Toner save mode can be enabled to reduce toner consumption by about 10%. 1 Press the [AUTO/TEXT/PHOTO] key ( AUTO / / ) to select "TEXT" ( ). 2 Hold down the [AUTO/TEXT/PHOTO] key ( AUTO / / ) until the PHOTO indicator ( ) blinks. AUTO 3 1 3 5 To enable toner save mode, press the [Light] key ( ). To disable toner save mode, press the [Dark] key ( ). 1 3 5 4 The exposure level indicators show the current setting.
AL-1633_1644_EX.book 38 ページ 2003年10月23日 木曜日 午後8時21分 CUSTOMISING SETTINGS (User programs) The user programs allow you to customise the machine to match your needs. USER PROGRAMS Program number 1 Program name Auto clear time Preheat mode 1: 1 min. 2: 5 min. 3: 30 min. 4: 60 min. 5: 120 min. 6: 240 min. 3 Auto power shut-off timer 1: 5 min. 2: 30 min. 3: 60 min. 4: 120 min. 5: 240 min.
AL-1633_1644_EX.book 39 ページ 2003年10月23日 木曜日 午後8時21分 USER SETTINGS Setting codes (factory default setting appears in bold) Program number Program name 19 Offset of paper output tray 0: OFF 1: ON 23 Resolution in Auto/Text mode 1: 300dpi 2: 600dpi 25 Key auto repeat 0: OFF 1: ON 26 27 28 29 1: Minimum (current response speed) 2: 0.5 sec. Key press time 3: 1.0 sec. 4: 1.5 sec. 5: 2.0 sec.
AL-1633_1644_EX.book 40 ページ 2003年10月23日 木曜日 午後8時21分 USER SETTINGS SELECTING A SETTING FOR A USER PROGRAM 1 Hold down the [Light] key ( ) until the alarm indicators ( , , , ) blink. 4 Enter the desired setting code by pressing a numeric key. • For the setting codes, see "USER PROGRAMS". (p.38 to p.39) • The selected setting code blinks. • For example, to select 90 seconds, press the [5] key. The display shows "- -" with the left hyphen blinking.
AL-1633_1644_EX.book 41 ページ 2003年10月23日 木曜日 午後8時21分 SETTINGS FOR AUDITING MODE AUDITING MODE When "Auditing mode" is enabled, a count is kept of the number of copies made by each account (up to 20 accounts can be established), and the counts can be displayed and totalled as necessary. In "Auditing mode", the display shows "- - -", and this indicates that a 3-digit account number must be entered in order to use the machine for copying.
AL-1633_1644_EX.book 42 ページ 2003年10月23日 木曜日 午後8時21分 USER SETTINGS SELECTING AUDITING MODE SETTINGS 1 Hold down the [Light] key ( ) until the alarm indicators ( , , , ) blink. The display shows "- -" with the left hyphen blinking. 1 3 5 2 Enter the program number with the numeric keys. READ END Note 3 • See "AUDITING MODE SETTINGS" (p.41) for the program numbers. • The selected program number blinks. • For example, to select "Auditing mode", enter "10".
AL-1633_1644_EX.book 43 ページ 2003年10月23日 木曜日 午後8時21分 USER SETTINGS Auditing mode Account number deletion (program No.10) (program No.13) 1 Use this procedure to delete account numbers. A single account number can be deleted, or all account numbers at once. If no account numbers have been established, the error code "13E" will appear in the display. Press the [1] key to enable "Auditing mode" or the [0] key to disable it, and then press the [START] key ( ).
AL-1633_1644_EX.book 44 ページ 2003年10月23日 木曜日 午後8時21分 USER SETTINGS Resetting account (program No.15) The copy count of a single account or all accounts can be reset to 0. If no account numbers have been established, the error code "15E" will appear in the display. Copying when "Auditing mode" is enabled When "Auditing mode" is enabled, "- - -" appears in the display. [Resetting all accounts] Press the [1] key and then press the [START] key ( ). The copy counts of all accounts will be deleted.
AL-1633_1644_EX.book 45 ページ 5 2003年10月23日 木曜日 午後8時21分 Chapter 5 TROUBLESHOOTING This chapter describes troubleshooting and misfeed removal. TROUBLESHOOTING If you experience difficulty using the machine, check the following troubleshooting guide before calling for service. Many problems can be easily resolved by the user. If you are unable to solve the problem using the troubleshooting guide, turn off the power switch and unplug the machine, and contact your authorised service representative.
AL-1633_1644_EX.book 46 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING MACHINE/COPYING PROBLEMS The following problems are related to the general operation of the machine and copying. Problem Cause and solution The machine is not plugged into a power outlet. → Plug the machine into a grounded outlet. Power switch OFF. – 15 → Turn the power switch ON. The POWER SAVE indicator ( Page ) is blinking. → Indicates that the machine is warming up.
AL-1633_1644_EX.book 47 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING Problem Cause and solution Misfeed occurs. → To remove the misfeed, see "MISFEED REMOVAL". The paper is outside of the specified size and weight range. Page 54 16 → Use copy paper within the specified range. Paper curled or damp. → Do not use curled or crimped paper. Replace with dry copy paper.
AL-1633_1644_EX.book 48 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING Problem Cause and solution The document glass or the underside of the document cover/SPF is dirty. Page 66 → Clean regularly. Copies are smudged or dirty. Original smudged or blotchy. – → Use a clean original. The scanner glass in the SPF is dirty. → Clean the long, narrow glass in the SPF. White or black lines appear on copies. The transfer charger is dirty. 67 → Clean the transfer charger.
AL-1633_1644_EX.book 49 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING PRINTING AND SCANNING PROBLEMS In addition to this section, troubleshooting information can also be found in the README files for each of the software programs. To view a README file, see the "Software Setup Guide". Problem Cause and solution Page The machine is set to off-line mode. → Press the [ON LINE] key ( ( ). ) to turn on the ON LINE indicator 32 The machine is not correctly connected with your computer.
AL-1633_1644_EX.book 50 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING Problem Printing is slow. The printed image is light and uneven. Cause and solution Simultaneous use of two or more application software programs. → Start printing after quitting all unused application software programs. Page – The paper is loaded so that printing takes place on the back side of the paper. → Some paper types have a front and back side.
AL-1633_1644_EX.book 51 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING Problem Cause and solution The document glass or the underside of the document cover/SPF is dirty. Page 66 → Clean regularly. The original is smudged or blotchy. → Use a clean original. – You have not specified a suitable resolution. → Make sure that the resolution setting in the scanner driver is appropriate for the original. – You are scanning a large area (for example an entire A3) at high resolution.
AL-1633_1644_EX.book 52 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING Problem Cause and solution Page If scanning is not possible, shut down your computer, turn off the machine’s power switch, and unplug the machine’s power cord. Next, start your computer, restore power to the machine, and try scanning again. If scanning is still not possible, check the following items. – Your application is not TWAIN/WIA compliant. → If your application is not TWAIN/WIA compliant, scanning will not be possible.
AL-1633_1644_EX.book 53 ページ 2003年10月23日 木曜日 午後8時21分 INDICATORS AND DISPLAY MESSAGES If one of the following indicators lights up or one of the following messages appears in the display, check the meaning of the indicator or message in the following table and take appropriate action.
AL-1633_1644_EX.book 54 ページ 2003年10月23日 木曜日 午後8時21分 MISFEED REMOVAL When a misfeed occurs, the misfeed indicator ( ) and a misfeed location indicator ( ) will blink and the machine will automatically stop. Check the blinking misfeed location indicator to identify the location of the misfeed and remove it. Note The paper may tear when you remove a misfeed. In this event, be sure to remove all torn pieces of paper from the machine, taking care not to touch the drum cartridge (the green part).
AL-1633_1644_EX.book 55 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING Section C Remove the misfed original from the exit area. 3 Return the originals indicated by the minus number in the display to the document feeder tray and press the [START] key ( ). Copying will resume from the originals that still remained when the misfeed occurred. If the misfed original cannot be easily removed from the exit area, open the moveable part of the document feeder tray and remove the original.
AL-1633_1644_EX.book 56 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING MISFEED IN THE MACHINE 1 Open the bypass tray and the side cover. 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, go to "B. Misfeed in the fusing area". If the misfed paper is visible here, go to "C. Misfeed in the transport area". If paper is misfed here, go to "A. Misfeed in the paper feed area". A.
AL-1633_1644_EX.book 57 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING B. Misfeed in the fusing area 1 Push gently on both ends of the front cover and open it. 2 Turn the roller rotating knob in the direction of the arrow. 4 Lift the fusing unit release levers, to return them to their operating position. 5 Close the front cover and side cover. Roller rotating knob 3 The misfeed indicator ( ) will go out. Carefully remove the misfed paper.
AL-1633_1644_EX.book 58 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING C. Misfeed in the transport area 1 Open the fusing paper guide by pressing down the projection on either side of the guide and remove the misfed paper. Be careful not to tear the misfed paper during removal. The fusing unit is hot. Do not touch Warning the fusing unit when removing misfed paper. Doing so may cause a burn or injury.
AL-1633_1644_EX.book 59 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING MISFEED IN THE UPPER PAPER TRAY Note 1 Make sure that there is no misfed paper in the tray before pulling it out. (p.56) Lift and pull out the upper paper tray and remove the misfed paper. Be careful not to tear the misfed paper during removal. 2 Open and close the side cover. The misfeed indicator ( ) will go out. Note 3 5 • When closing the side cover, press on the handle.
AL-1633_1644_EX.book 60 ページ 2003年10月23日 木曜日 午後8時21分 TROUBLESHOOTING MISFEED IN THE LOWER PAPER TRAY (Two-tray model only) Note 1 Make sure that there is no misfed paper in the tray before pulling it out. (p.56) Open the lower side cover. Grasp the handle to open the lower side cover. 2 Remove the misfed paper. Be careful not to tear the misfed paper during removal. 3 If the misfed paper is not seen in step 2, lift and pull out the lower paper tray and remove the misfed paper.
!Chapter5.fm 61 ページ 2003年10月24日 金曜日 午後2時46分 REPLACING THE TD CARTRIDGE When the TD cartridge replacement required indicator ( ) lights up, the TD cartridge will need replacement soon. Obtain a new cartridge. When the TD cartridge replacement required indicator ( ) blinks, the TD cartridge must be replaced before copying can be resumed. Replace the TD cartridge by following the procedure below. Note When the TD cartridge replacement indicator ( 1 Push on both ends of the front cover and open it.
!Chapter5.fm 62 ページ 2004年3月26日 金曜日 午前11時33分 TROUBLESHOOTING 6 Close the front cover. Note The TD cartridge replacement required indicator ( ) will go out. • Before closing the front cover, make sure that the TD cartridge is correctly installed. • When closing the front cover, gently hold both ends. REPLACING THE DRUM CARTRIDGE The useful life of the drum cartridge is approximately 30,000 copies.
!Chapter5.fm 63 ページ 2004年3月26日 金曜日 午前11時33分 TROUBLESHOOTING 5 Remove the new drum cartridge from the protective bag and gently insert the lead end of the drum cartridge along the guides. Do not touch the drum cartridge (green Caution portion). Doing so may damage the drum and cause smudges on copies. 6 Remove the protective cover from the drum cartridge and then push the cartridge all the way into the machine. 1 2 7 5 Insert the TD cartridge along the guides until it locks in place.
AL-1633_1644_EX.book 64 ページ 6 2003年10月23日 木曜日 午後8時21分 Chapter 6 ROUTINE MAINTENANCE This chapter explains how to keep the machine operating smoothly, including viewing copy count, and scan count, the toner level indicator or drum cartridge life, and cleaning the machine. CHECKING THE TOTAL OUTPUT COUNT CHECKING THE TOTAL OUTPUT COUNT From the "0" display, you can check the total output count, total copy count, and total scan count as explained below.
AL-1633_1644_EX.book 65 ページ 2003年10月23日 木曜日 午後8時21分 CHECKING THE TONER LEVEL AND DRUM CARTRIDGE LIFE TONER LEVEL DRUM CARTRIDGE LIFE The toner level is indicated by a 6-level display. Use it as a guideline for replacing the TD cartridge. To find out how many more copies can be made before the 30,000 mark is reached, follow the procedure described below. 1 Hold down the [Light] key ( ) until the alarm indicators ( , , , ) blink. 1 The display will show "- -".
AL-1633_1644_EX.book 66 ページ 2003年10月23日 木曜日 午後8時21分 ROUTINE MAINTENANCE CLEANING THE DOCUMENT GLASS AND SPF/ DOCUMENT COVER If the document glass, SPF underside of the document cover, or the scanner for originals coming from the SPF (the long narrow glass surface on the right side of the document glass) become dirty, the dirt may appear on copies. Always keep these parts clean. Stains or dirt on the document glass/SPF will also be copied.
AL-1633_1644_EX.book 67 ページ 2003年10月23日 木曜日 午後8時21分 ROUTINE MAINTENANCE CLEANING THE TRANSFER CHARGER If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. 1 Turn the power switch off. 2 Open the bypass tray and the side cover. 3 Lift and pull out the upper paper tray. 4 Take the charger cleaner out by holding the tab. 6 Return the charger cleaner to its original position. Close the upper paper tray.
AL-1633_1644_EX.book 68 ページ 7 2003年10月23日 木曜日 午後8時21分 Chapter 7 SUPPLIES STORAGE OF SUPPLIES Standard supplies for this product that are to be replaced by the user are paper, TD cartridge and drum cartridge. For best copying results, be sure to use only SHARP products. Only genuine SHARP consumables carry the Genuine Supplies label. GENUINE SUPPLIES SUPPLY PART NUMBERS PROPER STORAGE When ordering supplies, please use the correct part numbers as listed below.
!Chapter7.fm 69 ページ 2003年10月24日 金曜日 午後2時50分 MOVING INSTRUCTIONS When moving this machine, follow the procedure below. Note When moving this machine, be sure to remove the TD cartridge in advance. 1 Turn the power switch off and disconnect the power cord. 2 Push on both ends of the front cover and open it. 3 Pull the TD cartridge out while pulling up on the lock release lever. TD cartridge lock release lever Pull out the TD cartridge until the green strap handle can be grasped.
AL-1633_1644_EX.book 70 ページ 8 2003年10月23日 木曜日 午後8時21分 Chapter 8 APPENDIX SPECIFICATIONS Model AL-1633 AL-1644 Type Digital Multifunction System, Desktop Photoconductive type OPC drum Document glass type Fixed Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. A3 Copy size Max. A3 Min. A6 (A6 must be fed from the bypass tray) Image loss: Max. 4 mm (5/32") (leading and trailing edges) Max.
!Chapter8.fm 71 ページ 2004年3月26日 金曜日 午前11時33分 APPENDIX Operating conditions Temperature: 15°C to 30°C (59°F to 86°F), Humidity: 20% to 85% Noise level Sound Power Level LwA(1B=10dB) Copying: 6.2[B] Standby: 3.1[B] Sound Pressure Level LpA (bystander positions) Copying: 48[dB(A)] Standby: 16[dB(A)] Sound Pressure Level LpA (operator position) Copying: 50[dB(A)] Standby: 18[dB(A)] Noise emission measurement in accordance with ISO 7779. Emission concentration (measured according to RAL-UZ62) Ozone: 0.
AL-1633_1644_EX.book 72 ページ 2003年10月23日 木曜日 午後8時21分 APPENDIX Scanner Function Type Flatbed scanner Scanning method Document glass (AL-1633) / SPF (AL-1644) Light source Cold cathode fluorescent lamp Resolution* Basic: 600 dpi x 1200 dpi Setting range: 50dpi - 9600dpi Original types Sheet media, books Effective scanning area 297 mm (11.7") (Lengthwise) x 431 mm (17") (Width) Scanning speed 2.
AL-1633_1644_EX.book 73 ページ 2003年10月23日 木曜日 午後8時21分 SOFTWARE LICENSE PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. 1. License. The application, demonstration, system and other software accompanying this License, whether on disk, in read only memory, or on any other media (the "Software") and related documentation are licensed to you by SHARP.
AL-1633_1644_EX.book 74 ページ 2003年10月23日 木曜日 午後8時21分 6. Limited Warranty on Media. SHARP warrants the disks on which the Software is recorded to be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/or its Licensors and your exclusive remedy will be replacement of the disk which fails to meet the limited warranty provided by this Clause 6.
AL-1633_1644_EX.book 75 ページ 2003年10月23日 木曜日 午後8時21分 INDEX Symbols [ ] key....................................... 11, 28, 33, 34, 71 [ ] key......................................................... 11, 71 A About the operation manuals - Online Manual.................................................... 5 - Operation Manual .............................................. 5 - Software Setup Guide........................................ 5 Adjusting the automatic exposure level...................
AL-1633_1644_EX.book 76 ページ 2003年10月23日 木曜日 午後8時21分 N Normal copying - Document glass ............................................... 21 - SPF .................................................................. 22 Numeric keys ........................................ 11, 25, 40, 42 O Offset of paper output tray ...................................... 39 ON LINE indicator ............................................. 10, 32 ON LINE key .....................................................
AL-1633_1644_EX.book 77 ページ 2003年10月23日 木曜日 午後8時21分 INDEX BY PURPOSE Copying Automatic ratio selection ......................................... 25 Cancelling a copy run........................................ 21, 22 Copying, starting ............................................... 21, 22 Dual page copying .................................................. 30 Enlargement/reduction ............................................ 25 Exposure adjustment ..............................................
AL-1633_1644_EX.
AL-1633_1644_EX.
AL-1633_1644_EX.
AL-1633_1644_EX.
Cover4.