4GT15 14GT20 SERVICE MANUAL S30Y114GT15// COLOUR TELEVISION Chassis No. UA-1 (14GT15) (14GT20) MODELS 14GT15 14GT20 In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
14GT15 14GT20 SPECIFICATIONS Convergence................................................................. Self Convergence System Focus ............................................................ Electrostatic Focus High Bi-Potential Sweep Deflection ..................................................................................... Magnetic Intermediate Frequencies Picture IF Carrier .................................................................................. 38.9MHz Sound IF Carrier Frequency 5.
14GT15 14GT20 IMPORTANT SERVICE NOTES Maintenance and repair of this receiver should be done by qualified service personnel only. SERVICE OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE When servicing the high voltage system, remove static charge from it by Connecting a 10K ohm Resistor in series with an insulated wire(such as a test probe) between picture tube dag and 2nd anode lead. (AC line cord should be disconnected from AC outlet.) 1. 2. 3. 4.
14GT15 14GT20 ADJUSTMENT PRECAUTIONS This model's setting are adjusted in two different ways: through the I2C bus control and in the conventional analog manner. The adjustments via the I2C bus control include preset-only items and variable data. 1. Setting the service mode by the microprocessor. 1. Short JA 122 & JA 124 for 1 second and release to switch to the service mode position, and the microprocessor is in input mode. (Adjustment through the I2C bus control). (Use JWS Key to set as well). 2.
14GT15 14GT20 SERVICE MODE (1) In the Service Mode, Key is used to select the mode in the following order. AGC & GEOMETRIC MODE WHITE POINT ADJ. MODE SUB ADJ. MODE Y-DELAY ADJ. MODE MISC. OPTION MODE IC OPTION MODE OFFSET ADJ. MODE FORWARD : CH DOWN KEY REVERSE : CH UP KEY AGC & GEOMETRIC MODE WHITE POINT ADJ. MODE SUB ADJ. MODE ↓ AGC TAKE OVER POINT (AGC) ↓ VERTICAL SLOPE (V-LIN) ↓ VERTICAL AMP (V-AMP) ↓ VERTICAL SHIFT (V-CENT) ↓ HORIZONTAL SHIFT (H-CENT) ↓ S-CORRECTION (S-COR) ↓ W.P. RED STD.
14GT15 14GT20 Y-DELAY ADJ. MODE OFFSET ADJ.
14GT15 14GT20 USER DATA IN SERVICE MODE The flow of Mode lists as following, * Direct Key-in Step1 Mode RC COMMAND SERVICE-ITEM FUNCTION AGC CONTRAST DOWN V-LIN COLOUR DOWN V-AMP BRIGHTNESS DOWN V-CENT TINT DOWN H-CENT SHARPNESS DOWN EW / / SYSTEM HB BLUEBACK S-COR TIMER SUB-VOL CONTRAST UP SUB-CON COLOUR UP SUB-COL BRIGHTNESS UP SUB-BRI TINT UP TINT SUB TINT SHARPNESS UP SUB-SHP CHANNEL 1 DRI-GS CHANNEL 4 DRI-BS CHANNEL 7 CUT-R CHANNEL FLASH BACK CUT-G 7
14GT15 14GT20 AFTER SHORT JA 122 & JA 124 ,AND TURN ON THE MAIN POWER SWITCH,READ DATA FROM EEPROM ADDRESS 00H ~ 03H,AND COMPARE TO THE LIST BELOW, IF DIFFERENT, INITIALIZE THE EEPROM.
14GT15 14GT20 EEPROM ITEMS VERTICAL SCAN DISABLE BLACK STRETCH AUTOMATIC VOLUME LEVELING FAST FILTER IF-PLL ENABLE VERTICAL GUARD (RGB BLANKING) EHT TRACKING MODE (HCO) OVERSCAN SWITCH OFF AUTO COLOUR LIMIT FORCED COLOUR LIMIT SOUND SYSTEM M SOUND SYSTEM DK SOUND SYSTEM I SOUND SYSTEM BG PLAYBACK SECAM FE (RF) NTSC 3.58 FE (RF) NTSC 4.
14GT15 14GT20 SHIPPING SETTING & CHECKING (1) The following default data has been factory-set for the E2PROM.
14GT15 14GT20 PIF ADJUSTMENT No. Adjusting point 1 Tuner IFT ( PRESET ) Adjusting procedure/conditions 1. Get the tuner ready to receive the CH. E - 9 signal,but with no signal input. Adjust the PLL data. 2. Connect the sweep generator's output cable to the tuner antenna. ( RF SWEEP ) 3. Adjust the sweep generator's to 80dBuV. 4. Connect the response lead ( use LOW IMPEDANCE probe with wave detector ; see Fig.1 ) to the tuner's IF output terminal. ( This terminal must have the probe alone connected ). 5.
14GT15 14GT20 PURITY ADJUSTMENT No. Adjusting point 1 PURITY ADJ. Adjusting procedure/conditions 1. Receive the GREEN-ONLY signal. Adjust the beam current to about 500 µA. 2. Maintain the purity magnet at the zero magnetic field and keep the static convergence roughly adjusted. 3. Observe the points a, b as shown in Fig. 4-1 through the microscope. Adjust the landing to the A rank requirements. 4. Orient the raster rotation to 0 eastward. 5. Tighten up the deflection coil screws.
14GT15 14GT20 CONVERGENCE ADJUSTMENT No. Adjusting point 1 CONVERGENC ADJ. ( To be done after the purity adjustment. Adjusting procedure/conditions Waveform and others 1. Receive the "Crosshatch Pattern" signal. 2. Using the remote controller, call NORMAL mode. BGR B G R STATIC CONVERGENCE 1. Turn the 4-pole magnet to a proper opening angle in order to superpose the blue and red colours. 2.
GT15 14GT20 CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT No. Adjusting point 1 CRT CUTOFF ADJUSTMENT (I2C BUS CONTROL) Adjusting procedure/conditions 1. Switch TV to VIDEO mode,BLUE BACK OFF, with NO VIDEO signal. 2. Press R/C to set Picture Normal condition. 3. Connect the oscilloscope to Red OUT from IC801.(TP851) Range Sweep Waveform and others 3.0Vdc : 1 V/Div (DC) : 5 msec/Div 1V 4. Adjust SCREEN VR ,so that the tip of signal reach 3.0 Vdc + 0.1 Vdc.
14GT15 14GT20 HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT No. Adjusting point Adjusting procedure/conditions 1 V-SLOPE (I2C BUS CONTROL) 1. Receive Monoscope Pattern Signal. 2. Call the "V-LIN" mode. 3. Increase or decrease "V-LIN" by Volume key till the horizontal line in the center of monoscope is just at the position where the blanking starts. 2 V-SHIFT 50 (I2C BUS CONTROL) 1. Call the "V-CENT" mode. 2. Increase or decrease "V-CENT" by Volume key till the picture is centered.
14GT15 14GT20 NTSC CHROMA ADJUSTMENT No. Adjusting point 1 SUB-TINT (I2C BUS CONTROL) Adjusting procedure/conditions 1. Receive the "NTSC3.58 Colour Bar" signal through AV in. 2. Connect the oscilloscope to TP853 (Pin (5) of P882) BLUE-OUT. » Range : 100mV/div. (AC)(Use Probe 10:1) » Sweep time : 10 µsec/div. 3. Call the "SUB-TINT" mode in service mode. Adjust the "SUB-TINT" bus data to obtain the waveform shown as Fig. 9. 4. Clear the SERVICE mode.
14GT15 14GT20 FUNCTION OPERATION CHECKING (VIDEO AND AUDIO) No. Adjusting point Adjusting procedure/conditions 1 CONTRAST key 1. Receive "Monoscope Pattern" signal. 2. Set P-Mode to select CONTRAST. 3. Press Volume Up/Down key to check whether the CONTRAST effect is OK or not. 2 COLOUR key 1. Receive "Color Bar" signal. 2. Set P-Mode to select COLOUR. 3. Press Volume Up/Down key to check whether the COLOUR effect is OK or not. 3 BRIGHTNESS key 1. Receive "Monoscope Pattern" signal. 2.
14GT15 14GT20 FUNCTION OPERATION CHECKING (VIDEO AND AUDIO) (Continued) No. Adjusting point Adjusting procedure/conditions 9 COLOUR SYSTEM 1. Receive the "PAL COLOUR BAR" signal, press the COLOUR SYSTEM key to select modes except PAL, check the COLOUR is not working properly. Then, select the "PAL" mode. Check again its colour so that it is working properly. 2. Receive "NTSC 4.43/3.58 COLOUR BAR" signal through AV, press COLOUR SYSTEM key to select modes except N4.43/3.
14GT15 14GT20 MEMORY MAP ADDRESS (HEX) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F D7 D6 D5 DATA D4 D3 PASS WORD PASS WORD PASS WORD PASS WORD D2 D1 D0 MICON DEFAULT 55 4F 43 A1 E2PROM E2PROM CHASSIS CTV FINAL LAST INITIAL RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE SETTING DATA REMARK 00-FF 00-FF 00-FF 00-FF AGC TAKE-OVER V-SLOPE V-A
14GT15 14GT20 ADDRESS (HEX) 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F MICON E2PROM E2PROM CHASSIS CTV FINAL LAST INITIAL D3 D2 D1 D0 DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE SETTING DATA REMARK SHARPNESS-OFFSET (SECAM) 04 00-0F SHARPNESS-OFFSET (N443) 0C 00-0F SHARPNESS-OFFSET (N358) 08 00-0F DATA D7 D6 FCO SCM ACL N443 SM HP2
14GT15 14GT20 ADDRESS (HEX) 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF D7 DATA D5 D4 D3 D2 D1 TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TU
14GT15 14GT20 ADDRESS (HEX) C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF D7 DATA D5 D4 D3 D2 D1 TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-S
14GT15 14GT20 ADDRESS (HEX) 100 101 102 103 104 105 106 107 108 109 10A 10B 10C 10D 10E 10F 110 111 112 113 114 115 116 117 118 119 11A 11B 11C 11D 11E 11F 120 121 122 123 124 125 126 127 128 129 12A 12B 12C 12D 12E 12F 130 131 132 133 134 135 136 137 138 139 13A 13B 13C 13D 13E 13F MICON E2PROM E2PROM CHASSIS CTV FINAL LAST INITIAL DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE SETTING DATA REMARK POS 46 POS 47 DATA D7 D6 D5 D4 D3 D2 TUNING FREQUENCY (HIGHER PART) TUNING FREQU
14GT15 14GT20 ADDRESS (HEX) 140 141 142 143 144 145 146 147 148 149 14A 14B 14C 14D 14E 14F 150 151 152 153 154 155 156 157 158 159 15A 15B 15C 15D 15E 15F 160 161 162 163 164 165 166 167 168 169 16A 16B 16C 16D 16E 16F 170 171 172 173 174 175 176 177 178 179 17A 17B 17C 17D 17E 17F D7 DATA D5 D4 D3 D2 D1 TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (LOWER PART) S-SYS AFT (auto) TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY
14GT15 14GT20 ADDRESS (HEX) 180 181 182 183 184 185 186 187 188 189 18A 18B 18C 18D 18E 18F 190 191 192 193 194 195 196 197 198 199 19A 19B 19C 19D 19E 19F 1A0 1A1 1A2 1A3 1A4 1A5 1A6 1A7 1A8 1A9 1AA 1AB 1AC 1AD 1AE 1AF 1B0 1B1 1B2 1B3 1B4 1B5 1B6 1B7 1B8 1B9 1BB 1BB 1BC 1BD 1BE 1BF MICON E2PROM E2PROM CHASSIS CTV FINAL LAST INITIAL DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE SETTING DATA REMARK POS 89 DATA D7 D6 D5 D4 D3 D2 TUNING FREQUENCY (HIGHER PART) TUNING FREQUENCY (L
14GT15 14GT20 ADDRESS (HEX) 1C0 1C1 1C2 1C3 1C4 1C5 1C6 1C7 1C8 1C9 1CA 1CB 1CC 1CD 1CE 1CF 1D0 1D1 1D2 1D3 1D4 1D5 1D6 1D7 1D8 1D9 1DA 1DB 1DC 1DD 1DE 1DF 1E0 1E1 1E2 1E3 1E4 1E5 1E6 1E7 1E8 1E9 1EA 1EB 1EC 1ED 1EE 1EF 1F0 1F1 1F2 1F3 1F4 1F5 1F6 1F7 1F8 1F9 1FA 1FB 1FC 1FD 1FE 1FF DATA D7 D6 D5 D4 D3 D2 D1 D0 MICON E2PROM E2PROM CHASSIS CTV FINAL LAST INITIAL DEFAULT RANGE WRITE(CPU) CHECK DATA CHECK TYPE CHECK DATA CHECK TYPE SETTING DATA REMARK MODEL MODEL LETTER NO. LETTER NO.
14GT15 14GT20 TROUBLE SHOOTING TABLE NO RASTER Check F701. Blown out. Replace the fuse. Check T701 pin (7) voltage (Approx. 310V at 220V AC) Check R701, R707 and D709. The fuse is again blown out. Check IC701, D701,C707 and D710. Check Secondary Main+B (Pin (17) of T701 voltage:Approx. 115V) Check D758, IC702 and IC753. Check CRT connector K1-K5 bias. D1001 (Power LED Green) turns on. D1001 (Power LED Red) turns on or turns ON/OFF. Check R618 and R615. Check C878. Check IC801.
14GT15 14GT20 TROUBLE SHOOTING TABLE (Continued) CIRCUITS TO BE CHECKED: » Tuner. » PIF. » Automatic Gain Control. » (5V), (32V) Power Source. NO PICTURE, NO SOUND Does the noise level increase at max. Contrast, Brightness and Sound controls ? Noise increases but no signal is received. No snow noise. Does noise or signal appear at pin (40) of IC801 ? Check the tuner supply voltage LB must be approx. 5V. BT must be approx, 32V. And CH preset data check.
14GT15 14GT20 TROUBLE SHOOTING TABLE (Continued) NEITHER VERTICAL NOR HORIZONTAL SYNCHRONIZATION CIRCUIT TO BE CHECKED: » Sync. Separator Circuit. Check pins(16), (17) and (34) of IC801. DEFECTIVE VERTICAL AMP. AND VERTICAL LINEARITY Readjust vertical size. (Bas Data) Vertical linearity and size is abnormal. Check R504, R503, R506, R513, C517 and D501. NO VERTICAL SCAN Check IC501. Check C503 and C507. Check IC501.
14GT15 14GT20 TROUBLE SHOOTING TABLE (Continued) NO SPECIFIC COLOUR Is some colour produced in B/W broadcast reception ? Is the white balance properly adjusted ? Check IC801, R801, R802, R803, D804, D805, D806 and Q801. Readjust the white balance. The picture colour is cyan. The picture colour is magenta. The picture colour is yellow. Check Q871, Q883 and their adjacent circuits. Check Q870, Q885 and their adjacent circuits. Check Q872, Q887 and their adjacent circuits.
14GT15 14GT20 SOLID STATE DEVICE BASE DIAGRAM TOP VIEW 8 5 1 4 4 1 M24C04W 3 COLLECTOR COLLECTOR 2R :BG: BASE 2 FX0008GE BASE EMITTER EMITTER B709A D601A COLLECTOR 64 33 JC BASE 1 EMITTER 32 iX3368CEN0 2SC2735 SIDE VIEW + BASE COLLECTOR EMITTER 1 2 3 BASE COLLECTOR EMITTER 2SC1815 1 PST573J 2SC2482 ~ ~ - 3 SE115N DX0386CE ANODE (RED) CATHODE (COMMON) ANODE (GREEN) 1 12 1 2 3 B C E 2SD1877 KA7808 KA7805 PX0423CE 8 1 LA7016 1 TDA7056A 3 5 1 STRF6653
14GT15 14GT20 MODEL 14GT15 CHASSIS LAYOUT J I H G F E D C B A 1 2 3 4 5 6 32 7 8 9 10
14GT15 14GT20 MODEL 14GT20 CHASSIS LAYOUT J I H G F E D C B A 1 2 3 4 5 6 33 7 8 9 10
14GT15 14GT20 WAVEFORMS 34
14GT15 14GT20 DESCRIPTION OF SCHEMATIC DIAGRAM SAFETY NOTES: NOTES: 1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE REPLACING PARTS. 2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING. 1. The unit of resistance "ohm" is omitted. (K = 1000 ohms, M = Mega ohm). 2. All resistors are 1/8 watt, unless otherwise noted. 3. All capacitors are µF, unless otherwise noted. (P = µµF).
14GT15 14GT20 ■ Infrared Remote Control Unit RRMCG0025KJSA Note:The parts here shown are supplied as an assembly but not independently.
3 4 R101 1.8k 5 37 C130 102B 6 L117 L116 L106 L103 L102 L101 7 C107 103B R103 2.2k L116 1µ R102 1k C109 103B L202 L201 R106 47k C131 102B L108 R105 470k C204 39p R208 1.2k D103 IT407 8 J103 0 C1 2000p C213 102B D104 IT407 D102 IT402 R201 33k D201 IT402 C205 1.5p CH AGC R114 47k R108 27k R116 47k C111 102Y R141 270k R143 0 R142 100k Q101 S8304 C112 102B C206 102B L204 R202 47k C207 103B L118 1.
14GT15 14GT20 14GT15 , 14GT20 HOTEL MODE APPLICATION How to enable/disable the "Hotel Mode" ? Ans: a) Press the R/C (FUNCTION) key until language selection appear,within five second press the (one/two digit) key and keep pressing it for five second, then you can see the hotel mode with four digits password. b) Key in the four digits password starting with number "1", "3", "7", "9", then the hotel mode will be enable, you can switch on/off the hotel mode by using R/C (volume up/down) key.
14GT15 14GT20 SCHEMATIC DIAGRAM: MODEL 14GT20 HEAD PHONE Unit J I H G F CRT SOCKET Unit E D C B A 1 2 3 4 5 6 39 7 8 9 10
14GT15 14GT20 14GT15 14GT20 SCHEMATIC DIAGRAM: MODEL 14GT15 MAIN Unit J I H G F E D C B A 1 2 3 4 5 6 40 7 8 9 10 11 12 13 14 15 41 16 17 18 19
14GT15 14GT20 14GT15 14GT20 SCHEMATIC DIAGRAM: MODEL 14GT20 MAIN Unit J I H G F E D C B A 1 2 3 4 5 6 42 7 8 9 10 11 12 13 14 15 43 16 17 18 19
14GT15 14GT20 14GT15 14GT20 BLOCK DIAGRAM - 1/3:M0DEL 14GT15 MAIN BLOCK J I H G F E D C B A 1 2 3 4 5 6 44 7 8 9 10 11 12 13 14 15 45 16 17 18 19
14GT15 14GT20 14GT15 14GT20 BLOCK DIAGRAM - 2/3:M0DEL 14GT20 MAIN BLOCK J I H G F E D C B A 1 2 3 4 5 6 46 7 8 9 10 11 12 13 14 15 47 16 17 18 19
14GT15 14GT20 BLOCK DIAGRAM - 3/3: MODEL 14GT20 HEAD PHONE BLOCK J I H G F CRT BLOCK E D C B A 1 2 3 4 5 6 48 7 8 9 10
14GT15 14GT20 PRINTED WIRING BOARD ASSEMBLIES PWB-B: CRT Socket Unit (Wiring Side) J I H G F PWB-C: HEAD PHOME Unit (MODEL 14GT20) (Wiring Side) (Component Side) E D C B A 1 2 3 4 5 6 49 7 8 9 10
14GT15 14GT20 14GT15 14GT20 PWB-A: MAIN Unit (Wiring Side) J I H G F E D C B A 1 2 3 4 5 6 50 7 8 9 10 11 12 13 14 15 51 16 17 18 19
14GT15 14GT20 14GT15 14GT20 PWB-A: MAIN Unit (Component Side) J I H G F E D C B A 1 2 3 4 5 6 52 7 8 9 10 11 12 13 14 15 53 16 17 18 19
14GT15 14GT20 Ref. No. Part No. Description Code Ref. No. PARTS LIST PARTS REPLACEMENT "HOW TO ORDER REPLACEMENT PARTS" To have your order filled promptly and correctly, please furnish the following informations. MARK Ref. No. : SPARE PARTS-DELIVERY SECTION.
14GT15 14GT20 Ref. No. D804 D805 D806 D1001 D1004 D1007 D1008 D1009 D1010 å IC702 Part No. Description VHD1SS119//-1 VHD1SS119//-1 VHD1SS119//-1 RH-PX0423CEZZ VHD1SS119//-1 RH-EX0867CEZZ RH-EX0867CEZZ RH-EX0867CEZZ RH-EX0867CEZZ RH-FX0008GEZZ R R R R R R R R R J 1SS119 1SS119 1SS119 PHOTODiode 1SS119 Zener Diode Zener Diode Zener Diode Zener Diode PC123FY8 Code Ref. No.
14GT15 14GT20 Ref. No. C712 C713 C714 C715 C717 C718 C719 å C721 C751 C752 C753 C755 C759 C760 C761 C762 C801 C802 C803 C804 C805 C806 C807 C808 C809 C810 C811 C812 C813 C814 C1001 C1003 C1004 C1005 C1006 C1007 C1008 C1009 C1010 C1011 C1012 C1013 C1014 C1015 C1016 C1018 C1019 Part No.
14GT15 14GT20 Ref. No. Part No.
14GT15 14GT20 Ref. No. R881 R888 R898 R899 R882 R884 R886 R883 R885 R887 R892 R893 R894 Part No. VRD-RA2BE471J VRD-RA2BE471J VRD-RA2BE471J VRD-RA2BE471J VRS-VV3DB153J VRS-VV3DB153J VRS-VV3DB153J VRD-RM2HD272J VRD-RM2HD272J VRD-RM2HD272J VRD-RA2BE102J VRD-RA2BE102J VRD-RA2BE102J Description R R R R R R R R R R R R R 470 470 470 470 15k 15k 15k 2.7k 2.7k 2.
14GT15 14GT20 Ref. No. Part No. Description Code Ref. No. MODEL 14GT15 CABINET PARTS 1 1-1 1-2 1-3 1-4 1-5 1-6 1-7 2 CCABA0081WEA0 Front Cabinet Ass'y Not Available - Front Cabinet HBDGB0001KJSA R Badge, "SHARP" JBTN-0043KJSA Button, Control HDECQ0038KJSA LED/RC Cover JBTN-0044KJSA Button, Power MSPRC0021KJFW Spring, Power Button HDECQ0040KJSA AV Cover GCABB0055KJKA Rear Cabinet 2 Part No.
14GT15 14GT20 Ref. No. Part No. Description Code Ref. No. Part No. Description Code COPYRIGHT © 2000 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan TQ0866-S Mar.
