iMPORTANT SAFETY INSTRUCTIONS For Household UseOnly WHEN USING AN ELECTRICAL APPLIANCE, BASIC SAFETY PRECAUTIONS SHOULD ALWAYSRE OBSERVED, iNCLUDiNG THE FOLLOWING: READALLINSTRUCTIONS BEFOREUSING YOURSHARK_ NAVIGATORTM LIFT-AWAY®PRO. WARNING'. TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: GENERAL ELECTRICALSAFETY: 1. Unplug from electrical outletwhen not in use and before servicing. 2.
HOSE ATTACHMENTS: DUST CU P/FILTE RS/ACCESSORIES: 1. DO NOT use if airflow is restricted; if the air paths, the hose, or the accessoriesbecome blocked, turn the vacuum cleaner off. Remove Before turning on the vacuum: 2. 1. Make sure that all filters are thoroughly dry after routine cleaning. all obstructions before you turn on the unit again. 2. Keepthe end of the hose and accessory openings away from face and body. Make sure that dust cup and all filters are in place after routine maintenance.
This manual covers model numbers: NV355 NV356E NV356K NV357 NV355CS NV356KCS TECHNICAL SPECIFICATIONS Voltage: 120V.
Contents Thankyou for the Shark ® Lift-Away Pro e Getting Started 6 Mode 1: Upright Vac 8 Mode 2: Portable Lift-Away ® 10 Above-Floor Cleaning 11 Dust-Away'" 12 Hard Floor Attachment Use & Care Storage and Maintenance 13 Maintenance 14 Emptying the Dust Cup 14 Cleaning the Pro-Motor Filters 14 Cleaning the Post-Motor HEPAFilter 15 Cleaning the Power Brush 15 Cleaning the Motorized Floor Brush 16 Checking for Blockages 16 Ordering Parts 17 Troubleshooting Guide 18 Warranty
I Getting Started h Fig. l Fig. 2 Fig. 6 ACCESSORIES: DUST-AWAY _ HARD FLOORATTACHMENT Specializedhard floor attachment vacuumsup large particles, then re-usable micro-fiber pad traps extra fine dirt and dust for a superior bare floor clean. (Fig. 1) Use only in Portable Lift-Away ® mode. CREVICETOOL FIRST THING'S FIRST,YOU NEED TO KNOW WHAT'S IN THE BOX YOU JUST OPENED: Reachdeepinto narrowspacesand clean between cushions,under radiators and baseboardsand in hard to reachcrevicesand corners. (Fig.
Your new Shark _ Navigator TM LiftoAway different cleaning modes to meet a[[ your Away ® ° both with constant suction _ Pro vacuum cleaner can easily be configured cleaning needs: upright vacuum and portable into Lift- power. C Fig. 7 Fig. 8 MODES: 1 UPRIGHTVAC 2 PORTABLE LIFT-AWAY Take the Lift-Away Upright vacuuming- floors and carpets. (Fig. 7) ® ®with you around the house to clean hard to reach places, (Fig. 8) NV355 NV358E NV358K NV357 NV3550S NV356KCS IB E_lJ'l@U811 4.
Mode 1" Upright Vac To reducethe risk of electric shock, unplug the unit beforeassembling,adding or removingattachments or converting modes. ,_ WARNING: The On/Offswitch is on the top of the Lift-Away ®canister.Always ensurethe power is OFF CO" position) before pluggingand unplugging. _-I i Storage Upper Cord FLq.9 F_q.lo Fig. 11 TO ASSEMBLE: 5 Place the floor nozzle on a level surface.
Suction Release Collar area rugs @. 73 TO USE: 1 4 Rotate the cord release to quickly release the power cord. 2 Gently pressthe floor nozzledown with your foot while you graspthe handle and tilt it backtowards you, (Fig. 13) NOTE: Therotating brushon the motorized floor brushwill not spin unless the nozzle is flat Secure the power cord in the cord hook. against the floor and the handle is tilted back. II .....Brush RollON I .....
Mode 2: Portable Lift-Away ® i 14 Fig, 15 PORTABLELIFT-AWAY ® 1 Separatethe portable Lift-Away _ canisterfrom the floor nozzle by pressing the red release button (a) on the side of the canister. Gently hold the nozzle to the floor with your foot and pull the canister up.(Fig. 14) 2 Pressthe handle releasebutton (a) and pull the handle up or pressthe extensionwand release button (b) and pull the extensionwand up. 3 Attach desired accessoryonto the end of either the extensionwand or the handle.
Above-Floor Cleaning {__ Re_ease suctbn when "_" Fig, 17 duiiing d@i_te objects [u/nitue o/ all@arieS, Suction Release Collar CLEANABOVE THE FLOORIN UPRIGHTVAC OR PORTABLELIFT-AWAY ® MODE 4 1 Pressthe handle releasebutton and pull the handle up or pressthe extensionwand release button and pull the extensionwand up. 2 Attach desired accessoryonto the end of either the extensionwand or the handle.(Fig. 17) 3 Your vacuum has tremendous suction power.
Dust-Away TMHard Floor Attachment - Use and Care Fig, 18 ATTACH PAD Sliptwo of the tabs betweenthe suction nozzle and the Dust-Away base and attach them to the front fastenerson the base. Then pull the other two tabs tightly around to the back fasteners on the base. Forbest results,ensurethat the pad is flat againstthe bottom surface and secured tightly. (Fig. 18) 2 Do not use bleachor fabric softeners asthey may damageor leavea coating that will reducethe cleaningperformance of the pads.
Storage and Maintenance Quick Cord Release Lower Cord Storage_ STORE YOUR VACUUM SAFELY ,_ To reduce the risk of electric shock, unplug the unit 1 Convert your vacuum back to upright vac mode. before performing 2 Rotate the upper quick cord release to its upright troubleshooting any cleaning, maintenance, or position and coil the power cord loosely around the two clips. Clip the plug onto the cord to Reassemble all parts securely before operating vacuum, checks. secure. (Fig.
Maintenance COMPONENT MAINTENANCE SCHEDULE 1 DustCup Emptyeach time you vacuum. 2 Pre-Motor FoamFilter Rinseand air dry every3 months under normaluse. 3 Pre-Motor FeltFilter Rinseand air dry every3 months under normaluse. 4 Post-Motor HEPAFilter Clean onceevery 2 yearsor as needed. _, iMPORTANT:Lois e_Suction may Occui iffoam[i iersare notcteane8 e,Jeiy S,TiQ_ihs Rin£e a_ ab_,:L8 ar drycomplet@: Foam[i!ters may@Peard!rt_aff_r use_ihis is nOrma, Fig. 21 Fig.
Maintenance - cont'd I/ FLq, 25 FLg, 28 Fig. / CLEANING THE POWERBRUSH (modelsNV355& NV355CS only) 1 Slidethe locking latch (a) forward and tilt the bottom cover upward to remove. (Fig. 28) 2 Carefullyremoveany blockage or debris and cut away any build-up of hair or string wrapped around the rotating bristle brushwith scissors. 3 To reassemble,insert the tabs on the front edge of the bottom cover into the matchingholes in the top half and tilt it back down until it clicks into place.(Fig.
Maintenance - cont'd I Rotatin_ Brush Fig, 32 Fig. 34 Fig, 33 CLEANING THE MOTORIZED FLOOR BRUSH CHECKING Blockages may cause your vacuum to overheat and When your motorized floor brush needs cleaning or locks onto an object, it automatically shuts down to shut down.
Maintenance - cont'd Ordering Parts Fig, 36 Hose and Connections to Vacuum + Detach the stretch hose from the back of the portable Lift-Away + canisterby squeezing the tabs together and pulling up. (Fig. 33) Straightenout the hose and look inside for blockages.
Troubleshooting Guide Checkfilters to seeif they needcleaning,Follow instructionsfor rinsing and drying the filters before re-insertingbackinto the vacuum.(See "Maintenance" sectionsfor instructions.) Vacuum is not picking up dirt. Dustcup may befull; empty dust cup. Checkhoseand hose connectionsfor blockages;clear blockagesif required. If dust cup is empty,and attachmentinletsare clear,checkfor other blockages.
EURO-PRO FIVE-YEAR (5) LiMiTED WARRANTY EURO-PROOperating LLCwarrants this productto be free from materialdefectsandworkmanshipfor a periodof five (S)yearsfrom the date of purchasewhen utilized for normalhouseholduse,subjectto the following conditions, exclusionsand exceptions. Theliability of EURO-PROOperating LLCis limited solelyto the cost of the repair or replacementof the unit at our option.
NV355 NV356E NV356K NV357 NV355CS NV356KCS IBEq_c)811 4.