Safety Instructions

ManualsBrandsShaoxing Prolux Lighting ManualsElectronicsWireless Charger

CONGRATULATIONS!

You’ve purchased the ﬁnest in natural lighting technology with your new OttLite

product.

PRODUCT REGISTRATION FORM

Please complete the enclosed Product Registration Form and return it today by mail.

WARNING: To prevent electric shock, make sure the lamp is not plugged in until

all steps are complete.

NOTE: THIS UNIT IS FULLY ASSEMBLED

Remove lamp from packing, placing lamp body base (A) ﬂat on a steady surface.

Connect power adapter input (H) into connector (J) in the rear-bottom of the lamp.

Plug the power adapter (K) into a standard household 120V AC outlet. Note:

Only use with the supplied power adapter to avoid damage or ﬁre.

Turn the lamp ON & OFF using power switch (B) located in the front-upper side of

base (A). Power switch (B) is a “touch” switch that controls the dimmer function

for 3 levels of brightness.

To power LED settings, slightly touch the switch to achieve the following:

• turn lamp “ON” to ﬁrst lower-brightness; touch the switch “once”;

• for medium-brightness; touch the switch “twice”;

• for high-brightness; touch the switch “three-times”;

• to turn lamp “OFF”; touch the switch “four-times”.

Wireless charger for Qi-certiﬁed devices (C) is located in the center of base (A).

See Wireless Charging Instructions section for details.

To position the shade simply bend the ﬂex-neck (E) as needed to point the light.

Please hold the lamp base (A) while adjusting the lamp.

WIRELESS CHARGING INSTRUCTIONS:

Wireless charging requires a Qi-certiﬁed device. To determine if your device is

Qi-certiﬁed, please visit the Wireless Power Consortium website.

To wirelessly charge a device, perform the following:

• Place the device, which supports Qi wireless charging standard, face up on the middle

of the Qi wireless charging icon (C).

• When the device is centered on the Qi wireless charging icon (C), a solid BLUE

light (D) will indicate the device is charging properly. NOTE: If BLUE light is blinking

this indicates the device is not charging and needs to be properly centered.

• Check the charge level on your device periodically to determine when device is fully

charged.

CAUTION!

DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL

AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE.

SAFETY WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS

1. Turn lamp off and WAIT UNTIL LAMP HEAD (G) IS COOL before handling.

2. The LED panel (F) might get hot after several hours of continuous use DO NOT place

your hands directly on LED light panel.

3. Never use with an extension cord unless the plug can be fully inserted into the

receptacles in the extension cord.

4. Do not alter the plug.

5. The lamp head included with this unit cannot be replaced by the consumer.

6. INDOOR USE ONLY.

NOTE: The important safety instructions appearing in this instruction sheet are not meant

to cover all possible conditions and situations that may occur. It must be understood that

common sense, caution, and care must be used with any electrical product.

CAUTION!

IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS

DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE

AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.

CAUTION!

THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN

THE LIGHT SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.

CAUTION: Any change or modiﬁcation to product not expressly recognized by

OttLite Technologies voids OttLite’s responsibility for proper function of product.

FCC PART 15

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION:

To maintain compliance with the FCC’s RF exposure guidelines, place the product at least

20cm from nearby persons.

IC CANADA

This device contains licence-exempt transmitter(s)/receiver that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause

undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences et Développement économique Canada

applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux

deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage;

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage

est susceptible d’en compromettre le fonctionnement.

CAN RSS-216/CNR-216

CAN ICES-005 (B)/NMB-005 (B)

POWER ADAPTER SPECIFICATION:

Input: AC 100-240V, 50/60 Hz, 1.0A

Output: 13V DC, 1.8A with a Male DC Plug

Qi CHARGER SPECIFICATION:

Output: 5V, 1A or 5 watts

THIS LAMP CONTAINS a 5V, 2,1A USB output port (L) located on the bottom rear of

lamp. USB port can charge items such as tablets, cellular phones, etc.

The “Qi” symbol is a trademark of the Wireless Power Consortium

Infuse LED Desk Lamp with Wireless and USB Charging

CSA26KUQ CSA26KUQ-SHPR PL-0170UQ

INS190511 REV070119

Summary of content (1 pages)

PAGE 1
Infuse LED Desk Lamp with Wireless and USB Charging CONGRATULATIONS! You’ve purchased the finest in natural lighting technology with your new OttLite® product. PRODUCT REGISTRATION FORM Please complete the enclosed Product Registration Form and return it today by mail. G WARNING: To prevent electric shock, make sure the lamp is not plugged in until all steps are complete. E NOTE: THIS UNIT IS FULLY ASSEMBLED 1. Remove lamp from packing, placing lamp body base (A) flat on a steady surface. 2.