Zenchant Electronics Co., LTD Dual Mode Bluetooth MODULE SPECIFICATION Model: ZEN-BDM10-A Shanghai Zenchant Electronics Co.
Zenchant Electronics Co., LTD Dual Mode Bluetooth 1. Overview The ZEN-BDM10-A Bluetooth module is based on the BP02215-26AA chip design and conforms to the Bluetooth 5.0 specification. This module can realize Bluetooth BLE/SPP data transmission, voice transmission, Bluetooth music playback, U disk /TF card audio decoding, TF card reader and other functions.
Dual Mode Bluetooth Zenchant Electronics Co., LTD Smart home The data transfer 2. Pin Configuration 3. Module hardware function specifications 1.1 PMU Characteristics Symbol Parameter Min Typ Max Unit VBAT Voltage Input 2.2 3.7 5.5 V VDDIO Voltage output -3.3 -V ADC/DAC VMIC -3.1 -V Voltage IVDDIO Loading current --150 mA 1.
Zenchant Electronics Co., LTD Dual Mode Bluetooth Output Voltage High-Level VOH 2.7 --V VDDIO=3.3V Output Voltage 1.3 Internal Resistor Characteristics Internal Internal General High Port Pull-Up Pull-Dow Comment Output Drive Resistor n Resistor PAx PCx 8mA 24mA 10K 10K 1. PR1 Default Out 0 PBx 4mA 8mA 10K 10K 2. PR2 Default Pull up PRx 8mA 10mA 10K 10K 3. USBDP/DM default pull USBDM down 4mA -1.5K 15K USBDP 1.
Dual Mode Bluetooth Zenchant Electronics Co., LTD Relative Power π/4 DQPSK DEVM RMS Modulation DEVM 99% Accuracy DEVM Peak +2MHz Adjacent -2MHz Channel Transmit +3MHz Power -3MHz 1.6.2 Receive Basic Data Rate Parameter Sensitivity Co-channel Interference Rejection +1MHz +1MHz Adjacent Channel +2MHz Transmit Power -2MHz +3MHz -3MHz Enhanced Data Rate Parameter Sensitivity Co-channel Interference Rejection +1MHz +1MHz Adjacent Channel +2MHz Transmit Power -2MHz +3MHz -3MHz 1.
Zenchant Electronics Co., LTD ZEN-BDM10-A With a mask version 5. Release notes Date Version Instructions 2020.08.13 New document V1.
FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.
OEM Guidance 1. Applicable FCC rules This module is granted by Single Modular Approval. It complies to the requirements of FCC part 15C, section 15.247 rules. 2. The specific operational use conditions This module can be used in IoT devices. The input voltage to the module is nominally 2.2V-5.5V DC. The operational ambient temperature of the module is -20 to 85 degree C. Only the embedded PCB antenna is allowed. Any other external antenna is prohibited. 3.Limited module procedures N/A 4.
6. Antenna Antenna type :PCB Antenna; Antenna Max. Peak Gain -1.39dBi 7. Label and compliance information An exterior label on OEM’s end product can use wording such as the following: “Contains Transmitter Module FCC ID: 2AOC9-ZENBDM10A” or “Contains FCC ID: 2AOC9-ZENBDM10A” 8.
9. Additional testing, Part 15 Sub part B disclaimer The final host / module combination need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device.