X-C13SG-0 802.11bgn and BLE SoC X-C13SG-0 datasheet v1.0 Based on RISCV SOC Support Wi-Fi (802.11b/g/n) and BLE5.0 Wireless Standards www.chipfresh.com sales@chipfresh.com Shanghai ChipFresh Internet of Things Technology Co.
X-C13SG-0 802.11bgn and BLE SoC 1 Module Overview 1.1 Features MCU BLE • 32-bit RISC-V single-core processor • BLE 5.0 • 160 MHz CPU • Center frequency range of operating • 276 KB RAM channel:2400MHz-2483.5MHz • 128 KB ROM • Transmit Power（Max 15dBm） • 1 Kb eFuse • Receiver Sensitivity（-97 dBm） Wi-Fi • IEEE 802.11 b/g/n-compliant • Center frequency range of operating channel:2400MHz-2483.
X-C13SG-0 802.11bgn and BLE SoC 1.2 Description X-C13SG-0 is a fully self-contained small form-factor, single stream, 802.11b/g/n Wi-Fi and BLE baseband/MAC designs, which provide a wireless interface to any equipment with a serial or other interface for data transfer. X-C13SG-0 integrate MAC, base band processor, RF transceiver in hardware and all Wi-Fi protocol and configuration functionality and networking stack, embedded firmware to make a fully self-contained solution for a variety of applications.
X-C13SG-0 802.11bgn and BLE SoC CONTENTS 1 MODULE OVERVIEW....................................................................................................................................... 2 1.1 FEATURES..................................................................................................................................................... 2 1.2 DESCRIPTION........................................................................................................................................
X-C13SG-0 802.11bgn and BLE SoC LIST OF FIGURES FIGURE 1. BLOCK DIAGRAM...............................................................................................................................3 FIGURE 2. X-C13SG-0 PIN LAYOUT (TOP VIEW)................................................................................................. 8 FIGURE 3. X-C13SG-0 PHYSICAL DIMENSIONS.................................................................................................10 FIGURE 4. ORDERING INFORMATION.
X-C13SG-0 802.11bgn and BLE SoC LIST OF TABLES TABLE1. PINS DEFINITION.................................................................................................................................. 9 TABLE2. ABSOLUTE MAXIMUM RATINGS........................................................................................................12 TABLE3. RECOMMENDED OPERATING CONDITIONS...................................................................................... 12 TABLE4. ESD............................
X-C13SG-0 802.11bgn and BLE SoC HISTORY V 1.0 10-05-2021 First Version. Shanghai ChipFresh Internet of Things Technology Co.
X-C13SG-0 802.11bgn and BLE SoC 2 Hardware Introduction Pin Layout 2.1 X-C13SG-0 comes with a connector for an external antenna, please refer to Figure 2. Figure 2. X-C13SG-0 Pin Layout (Top View) Pin Description 2.2 The module has 23 pins. See pin definitions in Table 1. Pin Describtion Type 1,8,14,16,23 Ground P 2 GPIO8 IPD 3 RESET UART1_RX GPIO11 I,PU I Function GND Internal 10K pull-down resistor, Boot select: Low: boot from module flash. High: boot from external UART.
X-C13SG-0 11 GPIO3 Factory GPIO4 Ready 12 GPIO5 Link +3.3V 13 15 17 18 19 20 21 22 GPIO22 GPIO0 GPIO2 GPIO21 GPIO20 UART1_TX GPIO17 IPU O IPU/O P IPU/O IPU/O I/O IPU/O IPU/O O 802.11bgn and BLE SoC press this button ( “Low” > 4s ) and loose to make the module recover to factory setting. “0” – Boot-up OK; “1” – Boot-up Fail; “0” – Wi-Fi connect to router “1” – Wi-Fi unconncted; The maximum output current of the external power supply is recommended to be above 500mA.
X-C13SG-0 802.11bgn and BLE SoC Figure 3. 2.4 X-C13SG-0 Physical Dimensions Ordering Information Figure 4. Ordering Information Shanghai ChipFresh Internet of Things Technology Co.
X-C13SG-0 802.11bgn and BLE SoC 3 Dimensions of External Antenna Connector X-C13SG-0 uses the first generation external antenna connector as shown in Figure 5. Figure 5. Dimensions of External Antenna Connector Shanghai ChipFresh Internet of Things Technology Co.
X-C13SG-0 802.11bgn and BLE SoC 4 Electrical Characteristics 4.1 Absolute Maximum Ratings Parameter Power supply voltage I/O PIN Storage temperature Symbol VDD Table2. 4.2 Unit V V ℃ Absolute Maximum Ratings Symbol VDD - Table3. Min 2.1 -40 Type 3.3 - Max 3.6 85 Unit V ℃ Typ +/- 2000 2 +/-500 Unit V V Recommended Operating Conditions ESD Name ESD-HBM ESD-MM ESD-CDM Description Human body model class 2 Moisture sensitivity level Charge device model Table4. 4.4 Max 3.6 VDD+0.
X-C13SG-0 802.11bgn and BLE SoC Table5. 5 RF Standards Peripheral Schematics This is the typical application circuit of the module connected with peripheral components (for example, power supply, reset/factory button, led, and UART interface). Figure 6. Peripheral Schematics Shanghai ChipFresh Internet of Things Technology Co.
X-C13SG-0 802.11bgn and BLE SoC Product Handling 6 Reflow Profile 6.1 Solder the module in a single reflow. ℃ Peak Temp. 235 ~ 250 ℃ 250 217 200 Cooling zone Preheating zone Reflow zone 150 ~ 200 ℃ 60 ~ 120 s >217 ℃ 60 ~ 90s –1 ~ –5 ℃/s Soldering time > 30 s Ramp-up zone 1 ~ 3 ℃/s 100 50 25 Time (sec.) 0 0 50 100 150 200 250 Ramp-up zone — Temp.: 25 ~ 150 ℃ Time: 60 ~ 90 s Ramp-up rate: 1 ~ 3 ℃/s Preheating zone — Temp.: 150 ~ 200 ℃ Time: 60 ~ 120 s Reflow zone — Temp.
X-C13SG-0 802.11bgn and BLE SoC 6.3 Shelf life in sealed bag: 12 months, at <30℃ and <60% relative humidity (RH). Recommend to store at ≦10% RH with vacuum packing. The module is rated at the moisture sensitivity level (MSL) of 3. Device Handling Instruction (Module IC SMT Preparation) Baked required with 24 hours at 125+-5℃ before rework process. After bag is opened, devices that will be re-baked required after last baked with window time 168 hours.
X-C13SG-0 802.11bgn and BLE SoC A transmitter with a modular grant can be installed in different end-use products (referred to as a host, host product,or host device) by the grantee or other equipment manufacturer. A host product is required to comply with all applicable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion.
