Installation Instructions

ManualsBrandsShanghai Xiaoyan Technology ManualsElectronicsTerncy Switch Module

Table Of Contents

3. Connect output terminal

A. Connect device as per the type of load.

B. Connect L1 and L2 to the device

. (Fig.5)

Indicator

Button

Expand

Interface

Input

Terminal 1

Input

Terminal 2

Neutral Terminal

Patch Point

(live line)

Patch Point

(relay input)

Output Terminal 1

Output Terminal 2

Live Terminal

The Terncy Switch Module (Model: TERNCY-SM01-D2/

TERNCY-SM01-D3), is an easy to install accessory. By

installing it into switches, sockets or other electrical

devices, you can create a remote connection for smart

lighting, use voice control, create automations, or other

functions via Home center.

1. Connect L and N line

Connect L line to L, N line to N

. (Fig.1)

2. Connect input terminal

Connect two routes of lines to S1 and S2 respectively.

A.C. device: Connect L and IN with the

attached wire. (Fig.3)

D.C. device: Connect D.C. power line directly

to IN. (Fig.4)

For D.C. device, do not link L with IN.

A. Connect an LED indicator.

This can drive the LED indicators on switches or

supply power to external devices.

Unclench the cover of the interface. (Fig.6)

Insert the 6-pin header into the interface rmly

. (Fig.7)

Connect the +/- wire of LED1 or LED2 to the plus-n-minus

of the LED indicator

. (Fig.8)

Do not touch the expand interface whilst the power is on.

The Module supports up to two sets of 5V or 12V LED

indicator with 20mA max output current.

Switch Module follows ZigBee 3.0 wireless protocol.

It needs to be connected to N and L line at the same time.

Power o during installation to prevent electric shock.

N line

L line

N line

L line

D.C.

Power

Download the Terncy app from app markets or scan the

QR code below. Follow the instructions within the app

to connect the Switch Module to Home Center.

Click the "Add Device" button in the Device tab

of the Terncy app.

The new device can be found after 3 seconds

under power-on conditions.

Switch Module Introduction

Guidance

Guidance Guidance Guidance Indicator Light State Download and Install App Setting Up The Accessory for The First Time

Device

Add Device

3012

：

Add Device

Scanning

new devices

3012

：

Add Device

Add

Scanning

new devices

2798-01

连接其他设备

取消

Home

Add Home Center

Add End Point

Accessory

Terncy Switch Module

Model:TERNCY-SM01

Shanghai Xiaoyan Co.,Ltd

Fig.1 Fig.2 Fig.3

Fig.6 Fig.7 Fig.8

Fig.9

Fig.4

Fig.5

4. Connect to the expand interface

Connect 12V and GND of the 6-pin header to the

corresponding plus-n-minus of external device. (Fig.9)

The Module supports 12V d.c. with 50mA max

output current.

B. Supply power for external devices.

Indicator

State

Green light ashes

10 times per sec.

Green light always on

Green light ashes

every 2 sec.

Green light ashes

4 times per sec.

Connecting to Home

Center nearby

Powered on

Successfully connected

to Home Center

Failed to connect to

Home Center

(Fig.2)

Summary of content (6 pages)

PAGE 1
Switch Module Introduction Guidance Guidance The Terncy Switch Module (Model: TERNCY-SM01-D2/ TERNCY-SM01-D3), is an easy to install accessory. By installing it into switches, sockets or other electrical devices, you can create a remote connection for smart lighting, use voice control, create automations, or other functions via Home center. Switch Module follows ZigBee 3.0 wireless protocol. It needs to be connected to N and L line at the same time.
PAGE 2
Set Up The Accessory Again Application Scenarios Set Switch Type 12： 30 Home Device Add Device N line L line Add Device Scanning new devices Add Home Center Add连接其他设备 End Point Accessory 取消 Switch Module Input 1 Application Scenarios N line L line GND line Application Scenarios N line L line 1. Do not soak or wash your devices. 2. Keep products away from fire, high temperatures or any other extreme environment.
PAGE 3
Warranty Card Xiaoyan's after-sales service includes: Xiaoyan Tech shall remove any physical defects inherent in the device which are listed on the warranty card, free of charge, by replacing (at the sole discretion of Xiaoyan Tech) the defective device within a period of 15 days from the date of receipt by the consumer, and by repairing the defective components of the device within the period of 12 months from the date of receipt by the consumer. * The warranty may vary in different countries and regions.
PAGE 4
The Warranty Applies to: 1. surface damage resulting from mishandling during transport, or defects inherent in material or structure of the products; 2. failure of the buttons or indicator lights; 3. failure of wireless communication. The Warranty Does Not Apply: 1. when the warranty period has expired; 2. to damage resulting from repairing and introducing alterations by unauthorized persons; 3. to damage caused by using accessories not recommended by the manufacturer; 4.
PAGE 5
FCC Statement： Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 6
IC RSS warning This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.