User's Manual

ManualsBrandsSHANGHAI UTT TECHNOLOGIES ManualsElectronicsACCESS POINT

SN: 0902-0001-005

WLAN

Link/Act

LAN

Power

PoE Module (Optional)

Ceiling Mount Wireless Access Point

Support

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

Thank you for choosing the UTT Ceiling Mount Wireless Access Point (hereinafter as “Device").

The UTT WA Series Ceiling Mount AP is a best-in-class indoor Access Point specifically designed for business-class wireless network such as hotel, cafe, lounge, shopping mall, restaurant and school. The available

models are WA1700N, WA1900N, WA2200N, WA2500N and etc.

With a standard install design and stylish appearance, the Device can be installed on wall or ceiling without hassle. Powered with

integrated 802.3af Power over Ethernet standard (passive PoE for WA1700N), it allows installation in areas where power outlets are not readily available.

The Device can also be managed by UTT WX Series WiFi Controller when working in FIT Mode. The WX Series WiFi Controller User Guides are available for download at www.uttglobal.com/download/.

LED/Button/Interface Description

After the Device is powered on and wireless enabled, the WLAN LED indicator will blink when

transmitting/receiving wireless data.

When a device is connected to a port properly, the port’s corresponding LED indicator will be on. The indicator

will blink when there’s traffic on that port.

The LED indicator blinks twice per second when the system is operating properly, and it will blink slower if the

system is under heavy load.

With the Device powered on, press the Reset button with a bent paperclip for 5 seconds until the WLAN LED

indicator goes off, and then release the button. After that, the AP will restart itself and reset the device to factory

default settings.

The LAN interfaces provide a LAN connection to network devices, such as PCs or switches.

You may use this Ethernet interface to power the Device. Power can be provided by an UTT PoE Switch or a

802.3af PoE injector.

The Power interface is where you connect the provided power adapter.

The 2.4G LED indicator is on when 2.4GHz Wireless is enabled. The LED indicator blinks when

transmitting/receiving 2.4G wireless data.

The 5G LED indicator is on when 5GHz Wireless is enabled. The LED indicator blinks when

transmitting/receiving 5G wireless data.

SYS

Reset

PoE

2.4G

Summary of content (3 pages)

PAGE 1
Thank you for choosing the UTT Ceiling Mount Wireless Access Point (hereinafter as “Device"). The UTT WA Series Ceiling Mount AP is a best-in-class indoor Access Point specifically designed for business-class wireless network such as hotel, cafe, lounge, shopping mall, restaurant and school. The available models are WA1700N, WA1900N, WA2200N, WA2500N and etc. With a standard install design and stylish appearance, the Device can be installed on wall or ceiling without hassle. Powered with integrated 802.
PAGE 2
Place the mounting bracket in the center of the ceiling tile. Mark the mounting screw holes and 25 mm hole for the Ethernet cable. Use a drill bit to drill the screw holes, and cut or drill the 25 mm hole for the Ethernet cable feed. Secure the Mounting Bracket to the ceiling tile by using the Expansion Bolts. Then feed the Ethernet cable through the 25 mm hole. Connect the Ethernet cable to the Ethernet port of the Device. NOTE: 1.
PAGE 3
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.