User's Guide

Package Contents
The basic parameters Alarm statusLamp status
power bank x1
User guide x1
Name and content of toxic and harmful substances
contained in this product are shown in the following table
Points for Attention
Warning
·It is forbidden to place the power supply into water, and forbidden to wet it in storage & usage.
·It is forbidden to throw the power supply into fire or heat it. Far away from heat source & fire
source. It is forbidden to store the power supply when the temperature is above 60 ℃.
·It is forbidden to charge the power supply in fire source & extremely hot conditions!
·Please don’t use or store the power supply near the heat source!
·If the power supply is leaked or odor is given off, please remove it immediately from near the
open fire.
·Please use the dedicated charger!
·It is forbidden to short the positive & negative poles of the power supply with wire or other metal
objects. And it is forbidden to transport or store it with necklace, hair clip or other metal objects!
·It is forbidden to shock, throw or mechanically vibrate the power supply, rough treatment to the
device will destroy its sophisticated construction.
·It is forbidden to directly weld the power supply terminal!
·As for the power supply, it is forbidden to pierce it with nail, shock it with hammer or tread it. And
it is forbidden to knock it with other methods.
·It is forbidden to dismantle, disassemble or change the external structure of the power supply.
Important safety instructions
Thanks for using this product. This product is a kind of dedicated power supply for high capacity
Sunmi desktop devices, which applies the charge & discharge chips of 18650 battery cell & TI
etc. with excellent performances in all aspects of safety, efficiency, capacity, etc. Please don’t
use it on other non-Sunmi products!
·When connecting the charger to charge, the output of the charger needs to be match the
input parameters in the specifications.
·When there are exceptions of liquid leakage, bulge & expansion, etc. in the product, please
don’t use it any more and place it in a safe place.
·If the power supply gives off odor, gives out heat, deforms, changes color or has any other
exception, it is not allowed to go on using it; if the power supply is in use or being charged, you
must immediately take it off the charger and stop usage!
·If the power supply gives off odor or gives out heat, changes color or deforms, leaks liquid or has
any other exception, it is forbidden to connect the power supply to the charger or device.
Suggestions
· Please use it according to the suggestions provided by the power supply instructions.
· Keep the device dry. Rain water, moisture and various liquids or water content are all possible
to contain minerals, which will corrode the electronic circuit. If the device gets wet, please dry it
completely in the air.
· Never use or store the device in a dusty or dirty place, otherwise its detachable parts &
electronic elements will be destroyed.
· Never place the device in an overheated place. High temperature will shorten the lifetime of
the electronic device, destroy the battery, cause certain plastic components to deform or melt.
· Never place the device in a supercooled place, otherwise moisture will form inside the device
when its temperature rises to normal temperature, which will destroy the circuit board.
· Never wash the device with strong chemicals, cleaning agent or strong lotion.
· Never smear the device with pigment, which will cause foreign matter blockage in the
detachable parts and thus influencing the normal operation.
· Please put this product in a place unreachable to children or pets.
Statement
Our company will not be responsible for the results of the following actions
· Damage caused by usage of this product on non-Sunmi products;
· Damage caused by usage & maintenance not under the conditions of this guidance note;
· Our company will not be responsible for any damage or problem caused by any option or
consumable (not the initial product or recognized product provided by our company); (You
have no right to make product modifications or changes without the consent of our company)
Disclaimer
Due to the product update, certain details of this document may be inconsistent with the
product. Please refer to the material item. Our company owns the interpretative right of this
document. We reserve the right to modify this user guide without giving advance notice.
Definition of discharge state
ElectricityC(%)
LED1
C≥75%
50%≤C＜75%
25%≤C＜50%
10%≤C＜25%
0%＜C＜10%
LED2 LED3 LED4 LED5
off
LED1-5 state
off
on
onon on on
on on
off on
off off
off off
on
on
off off
off
off off
off
off
on
Definition of charging state
ElectricityC(%)
LED1
on
Full power
C≥75%
50%≤C＜75%
25%≤C＜50%
C＜25%
LED2
off
LED3
on
on
blink
LED4
on
LED5
off
LED1-5 state
on
onblink
onon
on
blink
blinkoff
off
off
on
off
off
off
off
off
off
Alarm status
Low level alarm
state frequency The length
LED1-4
off
LED5 blink continuous
buzzer A short sound continuous
0 electric alarm
LED1-4
off
LED5 Normally on
buzzer sing 60S
60S
Fault alarm
LED1-4
off
LED5 4S on-1S off
buzzer
4S Ring-1S stop
buzzer
off
60S
60S
Overheat
protection
alarm
LED1-4
It depends on
the power
LED5 2S on-2S off continuous
Power supply switchOutput (device interface)
Input (adapter interface)
LED 1
LED 2
LED 3
LED 4/LED 5
1
2
3
4
5
Connect the adapter DC plug adapted to POS machine to the input interface of the power bank;
Connect the AC power line plug of the adapter to the commercial power socket;
Plug the DC output line of the power bank in the input interface of POS machine;
Short press the power bank switch, and the indicator light is in working state when it is lit.
• Short press for 1 second, and the power bank is awakened from sleep mode to boot;
• Long press for 3 seconds, and the power bank is forced to power off from power-on state.
Multiple power bank can be used in tandem when longer usage is required.
Product Model
Li-Ion batteryContained Battery Type
Battery rated energy
Rated Capacity
Rated input
Rated output
Input Interface
Output Interface
Applicable Models
Security
Other Functions
Charging Temperature
Discharging Temperature
Size
Net Weight
2500mAh/DC18V(45Wh)
1500mAh/DC24V(36Wh)
5000mAh/DC18V(90Wh)
3000mAh/DC24V(72Wh)
DC24V/1.25A
DC24V/2.5A
DIN 4Pin
DIN 4Pin
SUNMI POS System
(T1/T1 MINI/T2/T2 MINI/T2 LITE/D1/D2)
Overcharge voltage protection
Over-discharge voltage protection
Over-temperature protection
Overcharge over-current protection
Discharge over-current protection
Short-circuit protection
Error-proof protection
Low battery sound and light alarm
5~45℃
-20~55℃
L168*W90*H48mm
794g 1013g
NB010 NB011
Name of parts
Circuit board
（Pb） (Hg) (Cd) (Cr(VII) (PBB) (PBDE)
Toxic and harmful substances and elements
Battery pack
Shell
Small structural
parts
:It indicates that the content of toxic and harmful substances in all
homogeneous materials of this part is below the limit specified in
SJ/T11363-2006.
:It indicates that the content of toxic and harmful substances is higher than
the limit specified in SJ/T11363-2006 in at least one homogeneous material
of this part; however, the the reason why the toxic substance of that part
exceeds the limit is that there is no applicable material to replace it
currently.
For products that have reached or passed the service years for environ-
mental protection, they should be recycled according to Measures for
Control and Management of Electronic Information Products and should
not be thrown away at will.
Manufacture
Shanghai Sunmi Technology Co.,Ltd.
Room 505 No.388 Song Hu Road Shanghai, China
3
2
1
4
5
Please read carefully this instruction manual before using the product, and keep it properly.
POWER BANK
12610751-00 190211
* Charging treasure must be within 5 ~ 45 ℃ environment temperature, and suggests that in 0 ℃ ~ 45 ℃ environment temperature range for discharge.
Charging and discharging outside this temperature range will result in a sharp decrease in cell capacity and a shorter service time.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.