Operation Manual

ManualsBrandsShanghai SAND Information Technology System ManualsElectronicsMobile payment terminal with GSM/GPRS and RFID reader

SAND_OS operation manual

Instruction

1. SAND_OS operation manual applies to the download and using of OS software of both POS and Tax

control serial products.

2. As per the difference of product model and hardware version, each specified OS version would be a little

different form one another, and result to the change of details of some operational interface. Anyhow, basic

operations are similar. If there is difference, they would be shown in their correspondent product manual.

3. The ROM and OS version will update unceasingly, content referred in this manual are just for

demonstration, the exact version please referred the newly send notice.

4. Difference versions of OS

may need to download display/printing word stock as well as resetting

the configuration, please pay attention.

I. OS system management instruction:

1.0 Power on (left column is the content of host display, right column are the Chinese

translation, below are the same)

04/03/16 13:24 04/03/16 13:24

OS V2.01-040324 OS V2.01-040324 （OS version No.）

SYSTEM SELFTEST… System self-check

CONFIG TEST… Check configuration

CONFIG ERROR!!! 02 Configuration error!!! 02

Table1-1

The system would self check after the power on. If there is not any errors it will pop in the main

menu directly; if there is error, it would be displayed, press “Enter” and pop in the main menu, one

has to input the password when enters into the main menu.

Possible errors and reasons: (for more OS error report please refer to SAND POS OS error report

comparison table )

1，CONFIG ERROR!!! : Configuration error! (Demand system configuring)

2，CACHE ERROR!!!：Cache memory test error!

3，BATTERY ERROR!!!：Battery voltage error! (Under voltage or over tension of the main board,

error would be prompted either lower than 2.8V or higher than 3.7V. )

4，ETHERNET ERROR!!!：Ethernet error! (setting incorrect or Ethernet fault )

5，ICC ERROR!!!：IC card error! (not found IC card or setting error)

6，PRINTER ERROR!!!：Printer error! (printer setting incorrect)

7，PRINTE DOT ERROR!!!：No printing word stock! (requires to download printing word stock)

8，GB2312 DOT ERROR!!!：No display word stock! (Requires to download display stock)

9，SDRAM ERROR!!!：SDRAM test error!

10，ERR: KEYBOARD ERROR! ：Keyboard test error! (Keyboard fault or else)

11，APP BAD SIZE：Application program length error. (Undownload application program or

application program cannot run.)

Summary of content (23 pages)

PAGE 1
SAND_OS operation manual Instruction 1. SAND_OS operation manual applies to the download and using of OS software of both POS and Tax control serial products. 2. As per the difference of product model and hardware version, each specified OS version would be a little different form one another, and result to the change of details of some operational interface. Anyhow, basic operations are similar. If there is difference, they would be shown in their correspondent product manual. 3.
PAGE 2
.0 Main menu Main menu totally one page 04/03/16 13:24 MAIN MENU 1 1．SYSTEM CONFIG 2．SOFTWARE DOWNLOAD 3．SOFTWARE DEVELOP 4．HARDWARE TEST 5．SYSTEM ADMIN Main menu 1．System configuration 2．Software download 3．Software development 4．Hardware test 5．System management 04/03/16 13:24 1 II. ROM and OS operating instruction: 1 OS downloading: 1.0 Starting interface introduction: Power on host LCD display Table2-1 00/00/00 00:00 00/00/00 00:00 ROM H2.7 S1.01-030911 ROM H2.7 S1.01-030911（ROM version No.
PAGE 3
2 Software download menu operation 2.
PAGE 4
2.3 OS download and ROM downloading and installation 2.4 APP download and ROM download and installation 2.5 DISP FONT download and installation After enters into DOWNLOAD DISP FONT, the host would display as follows: 04/03/16 13:24 04/03/16 13:24 DOWNLOAD DISP FONT Download display font WAIT DOWNLOAD Waiting for downloading Table2-7 SelectHZK16.
PAGE 5
04/03/16 13:24 TEST MENU 2 1．UART 2．PINPAD 3．MODEM 4．GPRS 5．ETHERNET 6．MEMORY 04/03/16 13:24 TEST MENU 3 1．BATTERY Test menu 1．Serial test 2．Pinpad test 3．Modem test 4．GPRS test 5．Ethernet test 6．Memory test Table3-2 Test menu 04/03/16 13:24 2 04/03/16 13:24 3 1．Battery test Table3-2 Continuous press F2 (line shift) in the page2 of the test menu to enter into page 3 of the test menu.
PAGE 6
attention to check it; Pixel printer: EPSON M190 Thermal printer: APS ELM205-LV Pixel printer with teeth hole paper printer: SAMSUNG SMP130U Press any key to begin to print, the host will display as follows after completion: 04/03/16 13:24 04/03/16 13:24 PRINTER TYPE： Printer type SAMSUNG SMP130U Samsung SMP130U TEST OK！ Test OK! CHECK PRINTER PAPER Check printing pater PRESS KEY TO CONTINUE Press any key to begin to test Press any key to return to the hardware test main menu after the test is completed.
PAGE 7
PRESS KEY TO CONTINUE Press any key to continue TRACK 2 refers to track 2; 0 refers to the condition of track is correct, other No. refer that the condition is incorrect; LEN 37 refers to the length of track; 601428．．．．refers to information of track Press any key to display information of track 3, which is basically similar to that of track 2, and then press any key again to display information of track 1.
PAGE 8
04/03/16 13:24 SELECT 1PAY．SYS．DDF01 6F15840E315041592E53 59532E4444463031A503 8801019000 04/03/16 13:24 Select file 6F15840E315041592E53 59532E4444463031A503 8801019000 90 00 90 00 REMOVE CARD Remove card 3B6F000．．．and 6F15840．．．are Resetting response and select file data respectively, since there would be diversity as per of difference of cards; 90 00 refers to the card is in correct condition, other figures all mean incorrect. 6.
PAGE 9
Insert SAM test card into SAM slot, then input correspondent SAM slot No, host displays as follows: 04/03/16 13:24 04/03/16 13:24 SAM NO.： 1 SAM slot No.
PAGE 10
(2) Test of both COM1 and COM2 should connect with PC serial port, take the test by using DNW software. 9 Pinpad test Select the second item 2．PINPAD in the hardware test menu and press “Enter”, display as follows: 04/03/16 13:24 04/03/16 13:24 PINPAD TEST MENU 1 Pinpad test menu 1 1．PINPAD DISPLAY 2．PINPAD KEYBOARD 1． Pinpad display test 2． Pinpad keyboard test 9.1 Pinpad display test Select 1．PINPAD DISPLAY and press “Enter”, pinpad will test automatically.
PAGE 11
04/03/16 13:24 MODEM TEST MENU 1 Modem test menu 1．ASYNC MODEM TEST 1 Async modem test 2．HDLC MODEM TEST 2 HDLC modem test 04/03/16 13:24 1 10.1 Async modem test Select 1．ASYNC MODEM TES and press “Enter” to begin to test with the following interface: 04/03/16 13:24 04/03/16 13:24 HDLC MODEM TEST HDLC modem test INPUT TEST NO.： Input test No. of times Input the No. of times and press “Enter”, then display as follows: 04/03/16 13:24 HDLC MODEM TEST HDLC modem test INPUT PHONE NO.： Input phone No.
PAGE 12
Ethernet test When testing Ethernet, test program send data to the backend platform through line, backend receives and settles it, then return to POS. POS displays the test information on DNW window through COM2. Connect POS COM2 and PC COM1 as well as line, and start DNW software.
PAGE 13
Press “Cancel” and return to its Previous Menu. 13.3 SRAM test Select 3．SRAM TEST and press “Enter” to begin to test, and it will display as follows: 04/03/16 13:24 04/03/16 13:24 SRAM TEST SRAM test CHECK APP．．． Check application… MEMORY TEST OK！ Memory test OK! Note! : The first time take SRAM test system would prompt the test failed, if is displays “MEMORY TEST OK！”during any of the following test, it means that the machine works normal.
PAGE 14
04/03/16 13:24 POWER IS OFF 04/03/16 13:24 Power is off PRESS KEY TO CONTINUE Press any key to continue Note! : The above test is to check whether the power board and reserved nickel-hydrogen battery work well. The machine can distinguish the external power supply is “on” or “off”. When the external power is “off”, there should not be system halted or resetting within one minute. Different from that of battery voltage. 14.
PAGE 15
1.0 Printing system setting Select 1.PRINT SETTING and confirm it, host will print configuration information of the system. The printing list is as follows: (the left column are the content, while the right are instrucitons) 2003/10/17 11:16 The already set Date and time in host HARDWARE SETTING Hardware configuration MODEL PS100 Model PS100 VER 2.70 Version 2.70 MSN 270030802001 Host serial No. 270030802001 PSN 100030802001 Pinpad serial No.
PAGE 16
04/03/16 13:24 HH:MM 04/03/16 13:24 HH:MM Table4-5 Input hour and minutes by way of keyboard, such as 1324 refers to 13:24. Return to the system configuration menu after the confirmation. 1.2 Hardware setting 1.2.1 Model setting Select 3.HARDWARE SETTING and confirm.
PAGE 17
The system would prompt to input Pinpad serial No. after confirmation, the interface is as follows: 04/03/16 13:24 04/03/16 13:24 PINPAD SERIAL NO： Pinpad serial No. 1000403020001 1000403020001 Table4-10 1.2.4 IC card reader setting After the completion setting and confirmation of serial No.
PAGE 18
1.2.7 Save After completion of all above setting, host will prompt as the following interface: 04/03/16 13:24 04/03/16 13:24 SAVE？ Save? 270030802001 VER ICC ETHERNET GPRS Serial No.: 270030802001 2.70 Version 2.7 EXIST IC card reader exist EXIST Ethernet exist NOT EXIST GPRS not exist Table4-14 Check all the displayed items, if true, press “Enter” to save; if not, press “Cancel” and reset it. 1.3 Battery setting Select 4.
PAGE 19
04/03/16 13:24 VOLTAGE（V） 70 APS ELM205-LV 04/03/16 13:24 （V） Printing voltage 70 APS ELM205-LV （ Thermal printer model） 00 00 00 00 00 00 Table4-17 When setting thermal printer, setting printing voltage at first based on different powers.
PAGE 20
04/03/16 13:24 SYNC ADJUST 3 SAMSUNG SMP130U 04/03/16 13:24 Sync adjust 3 SAMSUNG SMP130U（Pixel printer with teeth hole paper printer model） Table4-20 This setting is to adjust the tidiness of printing fonts; the value is capable form 0 to 9, press “Enter” to save after completion. Note! : Better take a printing test before this setting, and then set the value as per the deviation of printing fonts.
PAGE 21
04/03/16 13:24 DHCP ENABLE？ 0 1-Y 0-N 04/03/16 13:24 DHCP activated? 0 1-Yes 0-No Table4-23 Generally, it need not to be activated, so input “0”, after confirmation begin to set IP, the interface is as follows: 04/03/16 13:24 04/03/16 13:24 IP ADDRESS IP 172．16．40．77 172．16．40．77 Table4-24 Input the IP without decimal point if digits are three, input the decimal point if less three, such as: input “17216.40.77”refers to 172.16.40.77.
PAGE 22
1.
PAGE 23
Input the calling center help line of our company, this phone No. will be prompted to offer help when system checking out a mistake. 2.0 OS setting Select 5.