WM340 User Guide Ve r s io n 0 .
Contents Introduction ............................................................................................................................................... 3 Before using the terminal................................................................................................................... 3 Note about the security at the time of wireless LAN use .............................................................. 3 Supported OS (Personal Computers)...............................................
WM340 User Guide Version 0.2 Static DHCP .................................................................................................................................... 38 IP Filter............................................................................................................................................ 39 URL Filter........................................................................................................................................ 40 Device List ....................
WM340 User Guide Version 0.2 Introduction Thank you for purchasing the WM340 Please always read this user guide before using the product. Before using the terminal ・ It is not available, at the place that out of reach of radio waves such as in tunnels, underground, building and weak point, out of service. And you may not be available even in the high floor vantage point, such as high-rise apartment buildings. ・ If use overseas, please check with your customer center.
WM340 User Guide Version 0.2 Browser iOS 4 or later Mozilla Firefox 2.0 or later Internet Explorer 6.0 or later Safari 2.0 or later Opera 9.64 or later Disk free space 50MB Display Resolution 800 × 600 or more (1024 × 768 recommended). ・ Other than the above, it may not work. In addition, even if applicable to the above, by your environment, you may not operate properly. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Safety Notes Before using this product, please read the "Safety Notes" and use this product in the correct manner. The dangers or damage that can occur if the following precautions are not strictly adhered to or this product is not used in the correct manner are described below. Danger Warning Caution This sign denotes that death or serious injury may directly result from improper use. This sign denotes that death or serious injury may result from improper use.
WM340 User Guide Version 0.2 Notes about WM340 Danger Please do not use or leave the device in a place where it will be exposed to high temperatures, such as near a fire or heater, in strong, direct sunlight, or inside a car on a hot day. ●This may cause the device change shape or malfunction or overheat, catch fire. It may also cause the device to become hot, resulting in a burn injury. Please do not used near the vicinity of high-precision electronic devices.
WM340 User Guide Version 0.2 Please do not put in a microwave oven or other cooking device that use heat, or a high-pressure container. ●This may cause overheats, a fire, electric shock or malfunction. Please use the equipment always dedicated. ●If use the equipment not dedicated, it may cause overheats, a fire, explosion or malfunction. Please do not use this device while driving. ●This may cause traffic accident.
WM340 User Guide Version 0.2 Keep the device out of the reach of small children. ●Small children may accidentally swallow the device, or may injure themselves. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Notes about battery pack Danger Please do not use or leave the device in a place where it will be exposed to high temperatures, such as near a fire or heater, in strong, direct sunlight, or inside a car on a hot day. Please do not contact metal, such as the wire to the terminals. Please do not use any batteries other than this product. Also, please do not use it for other apparatus. Please do not use anything other than the appointed AC adaptor for charge.
WM340 User Guide Version 0.2 Please do not use it in a bathroom and do not put into water. Please do not use the device with wet hands. Caution When the liquid inside a battery pack adheres to the skin or clothing, Please wash away with clean water immediately. Keep the device out of the reach of small children. When the battery pack attached , if it was probably rust, nasty smell, generation of heat and other anomalies, please do not attached the battery pack into it.
WM340 User Guide Version 0.2 Note about AC adaptor Danger Please do not use an AC adapter other than the product. Please do not use it for other apparatus. AC adapter is connected directly to the outlet, please. Please do not use or leave the device in a place where it will be exposed to high temperatures, such as near a fire or heater, in strong, direct sunlight, or inside a car on a hot day. Please do not put in a microwave and high-pressure container.
WM340 User Guide Version 0.2 Please do not cover with cloth etc. Please do not place heavy objects on it. Please do not put on a dusty place. Please do not pull a code, when you extract the AC adapter. Please do not use it in a bathroom and do not put into water. Please do not use the device with wet hands. Caution Do not place the device on sloped or unstable surface. Keep the device out of the reach of small children. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.
WM340 User Guide Version 0.2 1. Power Button [Power OFF State] Pressed about 3 seconds, it displayed as "WELCOME" on the LCD screen, and the power is turned ON. [Power ON State] (1) Power OFF Pressed about 3 seconds, it displayed as "BYE" on the LCD screen, and the power is turned OFF. (2) Connect / Disconnect (WAN) If the power button is pressed for less than 2 seconds, be operated connect / disconnect by the WAN side. 2.
WM340 User Guide Version 0.2 LED Lamp State Red Flashes always Charging Green Flashes always Full charge Red Flashes Error Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Preparing USIM card Attaching 1. Please turn off the power, if the power of this product is on. 2. If this product is connected with USB cable or AC adapter, remove it. 3. Remove the cover. 4. Facing down the metal surface of the USIM card, insert the USIM card into the USIM slot in the upper right corner cutout. Cutout 5. Check the USIM card is attached. 6. Attach the cover. Removing 1. Please turn off the power, if the power of this product is on. 2.
WM340 User Guide Version 0.2 Setting Setting Set the fundamental connection item. 1. Do PC and USB cable connection or wireless LAN connection, please input the private IP address in the address field. The private IP address at the time of purchase is set 「http://192.168.0.1」. How to connect, check「Wireless LAN Connection procedure」、「USB Connection procedure」,please. 2. Displayed login screen. Input the password to log in. The password at the time of purchase is set 「password」.
WM340 User Guide Version 0.2 4. In administrator password setting screen, login password can be changed. The password at the time of purchase is set 「password」. Select 「Next」, after inputting administrator password. Setting Items Administrator password WEP key(initial value) Description Set the inputting password when connecting to Wi-Fi. The WEP key (5 digit number) at the time of purchase is set. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 The length of the password is dependent on the security mode. 5. In APN setting screen, using APN and default APN can be selected. Select 「Next」, after selecting APN. 6. In ｔhe default user setting screen, profile name／user name／password／APN／Tel／ Authentication type can be set.（Only if you select a 「default APN」, APN settings of the previous screen, the default user setting screen is displayed） Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 7. In the Wi-Fi setting screen, SSID／Security Mode／Wi-Fi password can be set. Select 「Finish」, after setting. Setting Items Description SSID WM340_XXX Network name（SSID） can set. Security Mode No encryption No security settings. WEP 64 Bit Shared Select wireless LAN security. WEP 128 Bit Shared If select WEP, Set the WEP key of 26 digits WEP 64 Bit Open or 10 digits. WEP 128 Bit Open WPA Personal TKIP If select WPA, Set the WPA key of 63 digits .
WM340 User Guide Version 0.2 Wireless LAN Connection procedure Connection procedure for this product 1. Turn on the power of this product. 2. Please search the network from the wireless LAN equipment. 3. SSID (WM340-XXX) of this product is displayed. If this product is chosen, a router and wireless LAN connection will begin. When WEP/WPA is set, the input of the WEP/WPA key is needed. Please enter the WEP/WPA key that is configured on the router. 4.
WM340 User Guide Version 0.2 Various function setting (Detail) About WM340 setting tool You can set the various functions of this product by using a Web browser from the USB cable this product and equipment, and wireless LAN connection. Please note that if you change the settings from the wireless LAN equipment, it may be disconnected wireless LAN. Starting of WM340 setting tool 1. Connect the USB cable or wireless LAN and PC, please enter the private IP address in the address field.
WM340 User Guide Version 0.2 3. Please click advanced settings. A detailed setup of each function is performed. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Internet Settings If you want to set up the Internet, Please make sure that the USIM card is inserted. Network Sets how to search the network to connect. 1. Sets the items. If you want to use in the domestic, please set to 3G the "Network Mode" and set to automatic the "Network Selection". Settings Network Mode Roaming Description 2G Only Search only the 2G. 3G Only Search only the 3G. ON WAN(2G／3G) roaming will be enabled.
WM340 User Guide Version 0.2 connect to that network. 2. Setting is complete, please press the Save button. Setting is updated. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Connection In order to connect to the Internet, sets the connection mode and profile. 1. Sets the items. The default profile has been registered. Please register a profile for the network as needed. The profile can be registered up to 10. Setting Items Connect Mode Description Auto Connect to Internet automatically. Manual Perform to connect and disconnect in the WM340 setting tool. Dial Demand Connect to the Internet when detects the device.
WM340 User Guide Version 0.2 2. To create APN profile by pressing the “New” button. Setting Items APN Profile Description Profile Name Please enter the name of any. User Name Please register a user name that carriers specify. Password Please register a password that carriers specify. APN Please register a APN that carriers specify. Tel Please register a Tel that carriers specify. Auth Type Please register a auth type that carriers specify.
WM340 User Guide Version 0.2 PIN Lock USIM card PIN code can be set. If you have configured, each time of power on enter the number of 4 to 8 digits. You can prevent unauthorized use by third parties. In this setting to change the PIN authentication enable or disable and the PIN code. 1. Switching the PIN authentication enable or disable. Select the "Lock" if you want to enable, please enter the PIN code of the current. Please press the, "Save" button after you enter. 2. Change the PIN code.
WM340 User Guide Version 0.2 Wireless LAN WLAN Setting Items Wi-Fi Connection Description Enable Wireless LAN connection will be enabled. Disable Wireless LAN connection will be disabled. Wi-Fi Channel 1、2、3、4、・・・、14 Set the Wi-Fi channel to be used. SSID WM340_XXX Set the SSID. Broadcast Enable SSID will be displayed in the connected equipment. Disable SSID is not displayed on the connected equipment. Max Number of Users 1、2、3、4、・・・、10 Limit the number of users to connect.
WM340 User Guide Version 0.2 Security Setting Items Security Mode Description None No security WEP 64 Bit Shared Select the wireless LAN security. WEP 128 Bit Shared If you select WEP, WEP key settings screen is WEP 64 Bit Open displayed. Set the WEP key of 10 digits or 26 WEP 128 Bit Open digits. WPA Personal TKIP If you select WPA, WPA key setting screen WPA Personal TKIP/AES will be displayed. Set the WPA key within 63 WPA2 Personal AES digits.
WM340 User Guide Version 0.2 Caution ・ If you changed the security, there are times when the device is unable to connect. In that case, please set the connection of the device again. ・ The recommended the setting to WPA or WPA2 from the safety of security. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 MAC filtering MAC filtering is the ability to control access from a particular MAC address. Setting Items MAC Filter MAC Filter Mode Enable MAC filtering feature will be enabled. Disable MAC filtering feature will be disabled. Allow all in list Block all in list MAC Filter List Description MAC Address Allow access only of MAC addresses that is registered in the list. Block the access of MAC addresses that are registered in the list.
WM340 User Guide Version 0.2 WPS WPS (Wi-Fi Protected Setup) is feature the easy connection to router. After select the PBC or PIN, WPS connection is initiated by pressing the "Save". Setting Items WPS Setting Enable WPS feature will be enabled. Disable WPS feature will be disabled. Connection Mode Description Please set the client PIN (PIN code of the Client PIN connected equipment). After setting the PIN, start automatically when you press the "Save" button.
WM340 User Guide Version 0.2 Caution ・ If broadcast of SSID is disabled, may be unable to connect. Want to use WPS, please enable the broadcast of the SSID. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Router Basic Allows to configure the UPnP(Universal Plug and Play). Caution ・ When do not need from security point of view, the recommend to disabled. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 LAN This item will do the following settings. ・IP addresses(router) ・Subnet Mask ・DHCP Server ・DHCP IP Pool ・DHCP Lease Time ・DNS Mode Setting Items IP Address Setting range 192.168.0.1 Description Is the router IP address in the LAN. "192.168.0.1" At the time of purchase has been set. Subnet Mask 255.255.255.0 Is the subnet mask in the LAN. DHCP Server Enable DHCP server assigns IP addresses automatically to devices within the LAN.
WM340 User Guide Version 0.2 Two Days 、 Half assigned automatically again. Week 、 One Week 、 Two Weeks DNS Mode Auto IP address of the DNS server will be set automatically. Manual Manually set the IP addresses of DNS server . Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Static DHCP Static IP address list you can set the IP address assigned to the client. The static IP address list can register up to 10 units. Setting Items Description Hostname Specifies the device to assign IP address. MAC Address Specifies the MAC address to assign IP address.。 IP Address Specifies the assign IP address. State When select a this item, will be enabled. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 IP Filter IP filtering feature is the ability to control access to specific IP address. Setting Items IP Filter Control No Filtering Block all in list IP Filter List IP Address(From) IP Address(To) Description IP filtering will be disabled. To blocks access to the IP address that is registered in the list. Specifies the starting IP address for a range of IP filtering. Specifies the ending IP address in the range of IP filtering.
WM340 User Guide Version 0.2 URL Filter Is the ability to control access to specific URL. Setting Items URL Filter Control URL Filter List Description No Filtering URL filtering feature will be disabled. Block all in list To blocks access to the URL that registered. URL Address Specifies the URL address to be filtered. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Device List Devices that are connected will be displayed. Display Items：Hostname、IP Address、MAC Address、Connect Mode Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 System Basic setting Sets the "login password", "language", "system work mode", "off time of backlight" Setting Items Change Password Language Description WEP key Change the login password. (initial value) Password at the time of purchase is "WEP key". English Sets to English the language of WM340 setting tool. Japanese Sets to Japanese the language of WM340 setting tool. System work mode performance Power save mode will be disabled.
WM340 User Guide Version 0.2 battery 5 minutes （ It is displayed only 10 minutes when 20 minutes mode power-saving is chosen in system action mode.） 30 minutes 40 minutes 50 minutes 60 minutes Turn Off Backlight Never After 10 seconds After 30 seconds After 60 seconds System log Save the system log of WM340. Setting Items Description Download To Download the log that is displayed. Clear To clear the log that is displayed. Refresh Update the log.
WM340 User Guide Version 0.2 Configuration This item will be the following functions. ・Reset(Settings) ・Backup Setting ・Restore Setting ・Firmware Update Setting Items Reset Description Back to the initial state. However, the state of the USIM card is not changed. Backup Settings Save the settings on your computer. Restore Settings Restore the configuration. Firmware Update Update the firmware. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Restart Restart the system. Copyright ©2011 FUJISOFT INCORPORATED, All rights reserved.
WM340 User Guide Version 0.2 Appendix Product Specifications Items Description Product Name WM340 External Dimensions 91.2mm(W)×62mm(H)×23.6mm(D) Weight Approximately 130g Battery Lithium-ion polymer 3.
WM340 User Guide Version 0.2 Output voltage ／ current : 5.0V／1.5A Trademarks *Windows, Windows 7, Windows Vista, Windows XP, Internet Explorer are trademarks or registered trademarks of the Microsoft Corporation in the U.S. and other country. *Macintosh, Mac, Mac OS are trademarks or registered trademarks of the Microsoft Corporation in the U.S. and other country. *Android are trademark or registered trademark of Google Inc.
WM340 User Guide Version 0.2 CE Warning Users have to use the connection to USB interfaces with USB 2.0 version or higher. Caution Risk of explosion if battery replaced aced by an incorrect type. Dispose of used batteries according to the instructions. Please make sure the temperature for adapter will not be higher than 45˚C Please make sure the temperature for device will not be higher than 45˚C The adapter shall be installed near the equipment and shall be easily accessible.
WM340 User Guide Version 0.2 FCC Regulations: lThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. lThis device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
WM340 User Guide Version 0.2 depending upon available accessories and FCC requirements.) While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.
