User's Manual

Connecting to Mi Home App
This product works with Mi Home and can be controlled using the Mi Home
app.
Scan the QR code to download and install the
Mi Home app. If you already have Mi Home app
installed, you will be directed to the device
connection page. You can also search for "Mi
Home" in an app store to download and install
the Mi Home app.
2. Insert four plastic expansion nuts into
the holes.
The camera has a power supply port and a LAN port. Waterproofing
must be done on both these ports.
1. Wrap the power supply port with the waterproofing tape as shown
below.
2. Wrap the LAN port with the waterproofing tape or a waterproofing
sleeve.
The LAN port can be wrapped with the waterproofing tape in the same way
as the power supply port.
For instructions on the use of a waterproofing sleeve, visit the IMiLab
WeChat account.
Waterproofing kit
3. Cover part of 2-in-1 power and
LAN cable with the base plate as
indicated.
Note:
In order to prevent accidents and injuries, please secure the device firmly
onto the wall as illustrated. The wall on which the device is mounted must
have a loading capacity of at least 3 times the weight of the device.
Do not install the device near a heat source, such as an air-conditioner
compressor, air vent of a range hood or air vent of a gas water heater.
As the camera can be rotated horizontally, please pay attention to the safe
turning distance during installation. Do not install the device at a location
where its horizontal movement would be impeded.
4. Put the base plate on the wall.
Ensure that the 2-in-1 power and
LAN cable goes straight down.
Secure the base plate by inserting
the screws into the expansion nuts.
Restoring factory settings
Press and hold the reset button to restore the factory settings. The content
inside the micro SD card will not be deleted.
Note:
When inserting or removing the micro SD card, please disconnect the camera
from the power supply. Please use a micro SD card from a reputable
manufacturer. The recommended read and write speed of the micro SD card
is at least U1/Class 10.
Connecting the Device
Turn on the camera
Step 1: Insert the power supply cable into the camera's power supply port.
Connect the other end of the power supply cable to a power source.
Step 2: When connected to a power supply, the indicator light will show
the camera's status. When the indicator light is yellow, the camera is being
turned on; when the indicator light is flashing yellow, it is waiting to be
connected.
Insert a micro SD card
Ensure that the camera is disconnected from the power supply. Use a
screwdriver to remove the protective case and expose the micro SD card
slot.
The contact points of the micro SD card should be facing the same
direction as the camera. Insert the micro SD card into the slot.
Note:
The actual operation may differ from the
instructions above due to Mi Home app
upgrades and updates. Please follow the
instructions shown by the Mi Home app.
Video Playback
Past videos can only be viewed when a compatible micro SD card is inserted
in IMiLab EC3 Outdoor Security Camera. After inserting a micro SD card and
turning on the device, the camera will automatically start recording.
In the control interface for . in the Mi Home app, tap the playback button to
enter the video playback page. You can also view a recording by selected a
time period..
IMiLab Smart Camera Outdoor...
12MB / s
06:20
Sharing a Video
In the control interface for IMiLab EC3 Outdoor Security Camera in the Mi
Home app, you can set the device as a shared device in the settings menu
and invite others to watch the recordings. Users must download the Mi Home
app and login to their Xiaomi account in order to view the recordings of the
shared device.
Share group
Check for firmware updates
Rename IMiLab Smart Camera...
Security settings
Share device
Remove device
Add Home screen shortcut
Feedback
Network info
Share with Mi Account
Share manage
Share...General settings
Infrared Night Vision
The light sensor can automatically switch the device to night vision mode
through IR-CUT based on changes in the lighting of the environment.
The device features 10 built-in infrared night vision lights that ensure
recording stays clear even in darkness.
Infrared night vision effect illustration
2019 3 2 20:51:05
About Works with Mi Home
A product that works with Mi Home can be controlled using the Mi Home app.
Please note that such products are only verified at the software level. Xiaomi
and Mi Home are not responsible for the production, implementation of
standards and quality control of these products and their manufacturers.
The working temperature of the device is -20℃ to 60℃. Do not use the
device when the temperature is too high or too low.
For better results, avoid placing the camera in front of or next or a glass
surface, a white-colored wall or other reflective surfaces as this may cause
the recording to have un-even lighting between the foreground and
background or be over-exposed.
Please ensure that the device is within Wi-Fi signal coverage. Place it at a
location with good Wi-Fi signal strength. Try to avoid placing the device
near a metallic object, a microwave oven or other objects that may cause
signal interference.
Home Security Precautions
Correct Disposal of this product. This marking indicates that product should
not be disposal with other household wastes through out the EU. To prevent
possible harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse sustainable reuse of
material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this
product for environment safe recycling.
WEEE Disposal and Recycling Information
For pluggable equipment, the socket-outlet (power adaptor) shall be installed near
the equipment and shall be easily accessible.
Hereby, Shanghai Imilab Technology Co., Ltd. declares that the radio equipment type
IMiLab EC3 Outdoor Security Camera is in compliance with Directive 2014/53/EU.
Adaptor Statements
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment. This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and canradiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for
help.
FCC 20cm Statement: This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20cm between the
radiator & your body. This transmi er must not be co-located or operating in
conjunction with any other antenna or transmier.
FCC Statement
The Home Security function can be turned on/off in the control interface
for IMiLab EC3 Outdoor Security Camera in the Mi Home app.
The device can detect and record movements within the viewing angle
and push the recording to the client. Users can set the surveillance time,
alert sensitivity, alert interval, etc.
Specifications
Product name: IMiLab EC3 Outdoor Security Camera
Model no.: CMSXJ25A
Power input: 12V 1A
Resolution: 1920×1080
Working temperature: -20℃~ 4
0℃
Video encoding: H.265
Wi-Fi connection: Wi-Fi IEEE 802.11 b/g/n 2.4GHz
LAN connection: 1 x 10/100M adaptive network port
Supported systems: Android 4.4 or iOS 9.0 or higher
CMIIT ID: 2019DP7988
Standard: Q31/0115000198C009-2018-01
Dimension: 126.6*91*116mm
Net weight: 788.6g
Diagonal angle: 110°
Aperture: F1.6
The distance between the base plate and the wall should be at least 50mm to
allow for a safety turning distance. Any gap of less than 50mm will result in
an obstruction to the camera's movement.
Top view
Please read this instruction manual carefully before using
the device and retain it for future reference.
Product Introduction
Wall base
(can be rotated
to adjust the
camera angle)
SpeakerKnob
Reset button
SD card slot
In this instruction manual, images of the device, accessories and user
interface are for illustrative purposes only and should only be used for
reference.
The actual device may differ from the illustrations due to product updates
and upgrades. Please refer to the actual device.
LAN port
Power supply
Indicator
light
Antenna
Mic
Packing list: IMiLab EC3 Outdoor Security Camera, wall mounting pack,
power adapter, waterproofing tape for power/LAN cable.
MicroSD
Micro SD card slot
Using a waterproofing sleeve
on the LAN port
Using the waterproofing tape
on the power supply port
Wrapping with
the waterproofing tape
IMILAB EC3 Outdoor Security Camera
User Manual
Installing the Device
Assemble the camera as shown below. Then secure the camera to the metal
rod with a screw.
Wrapping with the waterproofing tape
Scan the QR code below to follow the IMiLab WeChat account. Public WeChat
account.
Note: The warranty does not cover any damage caused by improper
installation. Please follow the instructions.
Locking mechanism
Connecting screw
(1 spare screw is available in
the accessory pack)
1. Attach the positioning sticker on the desired installation location. Drill four
holes at the positions indicated on the sticker. Drilling diameter of around
6.0mm; drilling depth of around 25mm.
Mounting the device
Note: Please check that the Wi-Fi signal is strong enough before
mounting the device.
Public WeChat
account
Manufacturer: Shanghai Imilab Technology Co., Ltd.
(a Mi Ecosystem Company)
Address: Room 908, No. 1, Lane 399, Shengxia Rd., China Pilot
Free Trade Zone, Shanghai, China 201210
For further information, please go to www.imilab.com.
Support: [e-mail]
For Business: [e-mail]
50mm
< 50mm
Note : This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates,uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.