FCC ID: 2ATCG-BB810QI4A BLE 5 MODULE BB810-QI4A Product Manual Manufacturer : Shanghai Ibeelink technology Co.,LTD Version Update Time Editor V1.00 2019-3-15 Alan Jiao V1.10 2019-4-17 Jack Wang V1.
Contents 1. Product Introduction .......................................................................................... - 1 1.1 Product Overview .............................................................................................. - 1 - 2. Detail Param ....................................................................................................... - 2 2.1 2.2 2.3 2.4 Performance .........................................................................................................
IOT service supplier who understands you best 1. Product Introduction 1.1 Product Overview BB810-QI4A is made by nRF52810 which is the baseline member of the nRF52 Series SoC family. It is built around an ARM® Cortex™-M4 CPU running at 64 MHz. It meets the challenge of bringing Bluetooth 5 feature sets and protocol concurrency to applications at a price point that makes adding Bluetooth 5 connectivity to an application compelling.
IOT service supplier who understands you best 2. Detail Param 2.1 Performance Form 1: Performance Module BB810-QI4A Soc nRF52810 QFN48 FLASH 192KB RAM 24KB VDD 1.8V to 3.6V PIN Num 25 Working FRQ 2.4GHz-2.
IOT service supplier who understands you best (Chip reference) RX: 4.6 mA peak current 0.3uA (3V VDD) in System OFF mode,no RAM retention Working Temperature -20℃~85℃ Storage Temperature -40℃~85℃ Package Size 13.5*19.4*3mm Compliance FCC PART 15 Subpart C 2.2 Mechanical specifications Picture 1 is the PCB mechanical specifications of the module. Picture 1: PCB Mechanical Specifications dimensions in millimeters Location:Rm.1502,East Tower,FIYTA Tech. Bldg.
IOT service supplier who understands you best Form 2 Length Width PCB Height PAD Size(Bottom) PIN Gap 13.51mm 19.41mm 0.8mm 0.81mm*0.8mm 1.27mm 2.3 PIN Description Form 3 Module PIN Description PIN PIN On nRF52 Description 1 P25 Digital I/O 2 P26 Digital I/O 3 P27 Digital I/O 4 P28 Analog input /Digital I/O 5 P29 Analog input /Digital I/O 6 P30 Analog input /Digital I/O 7 P31 Analog input /Digital I/O 8 GND GND 9 VCC 1.8 V ~3.6V 10 P0.
IOT service supplier who understands you best 22 P20 Digital I/O 23 P0.21/NRESET Digital I/O / Configurable as pin reset 24 SWCLK Serial wire debug clock input for debug and programming 25 SWDIO Serial wire debug I/O for debug and programming Note:Input voltage higher then VCC will destroy the module. 2.4 Soldering Reflow Guidelines Form 4 and picture 2 are reflow conditions and profile. Form4: Reflow conditions Picture 2: Reflow profile Location:Rm.1502,East Tower,FIYTA Tech. Bldg.
IOT service supplier who understands you best 2.5 PCB Layout Below is top layer of PCB: Below is bottom layer of PCB: Location:Rm.1502,East Tower,FIYTA Tech. Bldg.,Southern District of High-tech Industrial Park,Nanshan District,Shenzhen 518057,P.R.
IOT service supplier who understands you best 2.6 BOM List Below is BOM list. Items Value Specification Package nRF52810-QFA SOC Position Count U1 1 BT-XTAL_2016 X1 1 QFN40P600X600X90-48 nRF52810-QFAA QFN48 A N XTAL SMD 2016, 32MHz, Cl=8pF, XTAL 32MHz Total Tol: 10ppm Capacitor 0.
IOT service supplier who understands you best 3. Attentions 1、This module contains CMOS devices, need be protected from ESD. 2、Module needs to connect GND well, to reduce parasitic inductance. 3、If module needs reflow, pay attention to reflow profile. 4、Area below the ANT of this module, should not use polygon. 5、ANT of this module should be far away from other circuit. 6、Module should be placed as far as possible away from the other low frequency circuits or digital circuits.
IOT service supplier who understands you best If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module.
IOT service supplier who understands you best 4. Contacts 4.1 Buying Contacts Randy Ding(sales director) Phone:18676680772 Email:randy.ding@Honestar.com QQ/wechat:dzj18676680772 Location:Rm.1502,East Tower,FIYTA Tech. Bldg.,Southern District of High-tech Industrial Park,Nanshan District,Shenzhen 518057,P.R.China 4.2 Technical support Alan Lan(R & D director) Phone:13924619076 Email:alan.lan@Honestar.com Location:Rm.1502,East Tower,FIYTA Tech. Bldg.