User's Manual

ManualsBrandsShanghai Huace Navigation Technology ManualsElectronicsSKYDROID

SKYDROID User Manual

Attention:

If not obey the instruction to operate, it might cause financial loss and light injury or heavy injury.

Introduction

1、 Product Characteristics

series adopts GaoTongXiaolong 625 processor, equipped with Android embedded system,

advanced SDR technology, and super protocol stack, so that the image is clearer, lower delay, far

distance, stronger anti-interference, to which aircraft, robots, industrial control equipment can be

applied.

2、Main usage and Application range 1

It is used for remote control operation of helicopter, fixed wing, multi-rotor wing, car, ship and

other video image transmission (with optional camera), data transmission, and control of UAV

flight

3、 Spec and Parameters

Remote Controller Parameter

Model H12 Channels

Working Voltage 4.2V

radio-frequency

power

20DB@CE/23DB@FCC

Frequency 2.400-2.483GHz FHSS FHSS

Upgrade APP upgrade Weight 530g

Dimension 190*152*94mm Battery 10000mA/H

Duration of Flight 6-20 hours Charging Port TYPE-C

Application helicopter, fixed wing, multi-rotor wing, car, ship

Receiver Parameter

Model R12 Channel

Working Voltage 4.5-5.5V Working current 140MA@5V

Dimension 51*41*13 Weight 14g

R12

Frequency

2420-2480MHz

Modulation Type

QPSK

Summary of content (10 pages)

PAGE 1
SKYDROID User Manual Attention: If not obey the instruction to operate, it might cause financial loss and light injury or heavy injury. Introduction 1、 Product Characteristics R12 series adopts GaoTongXiaolong 625 processor, equipped with Android embedded system, advanced SDR technology, and super protocol stack, so that the image is clearer, lower delay, far distance, stronger anti-interference, to which aircraft, robots, industrial control equipment can be applied.
PAGE 2
4、Introduction on RC letters Remote Controller Long press the power button for 4 seconds to open the remote controller. No. Remark No. Remark 1 2.4G 3dB Antenna 10 Pump Switch B 2 Mode E Switch 11 Rotor X2、Y2 12 Button D 3 Dial G 4 Return C 13 Dial H 5 Rotor X1、Y1 14 AB Point Setting F 6 5.
PAGE 3
Receiver Name Description Name RED LED Red Led 2.4 ANT LED Green LED GND MODE KEY Mode Key VCC GND GND RX1 GN USB 5V DM/CH9 DP/CH10 Description Antenna Camera interface TX1 USB Upgrade Interface GND 5V GND RX2 RX3 TX2 TX3 Expansion Interface Data Transfer Interface /CBUS GND SBUS 2.
PAGE 4
5、Environment Condition （1）Environment temperature:-10°C~+55°Co （2）Stock temperature：-25°C〜+70°C。（3）Relative humidity：Not exceed 85%。（4）Atmospheric pressure:86kPa~106kPao (5) The use site is not allowed to have explosive dangerous medium, the surrounding medium should not contain corrosive metal and the gas that damage the insulation and conductive medium, not allowed to be full of water vapor and serious mold.
PAGE 5
Usage and Operation 1、Pre check and preparation ① Check whether the remote control power is sufficient before use. ② Before use, please check whether the antenna is placed as required to obtain the best effect. ③ Please make sure the firmware has been upgraded to the latest version for the first use. ④ users should ensure that they are not drunk, and under the influence of drugs operation.
PAGE 6
Status bar ①② ③④ ⑤ ⑥ ⑦ ⑧ （1）Bluetooth opening prompt （2）WIFI Signal （3）SIM card prompt window (the picture shows the state without SIM card inserted) （4）Power display (charging status in the picture) （5）Time display （6）View background process （7） Return to the main page （8） Return to the previous step
PAGE 7
H12Tool Introduction （1）For switching the hand settings （2）For checking rubber capacity （3）For matching the remote controller with other receivers (the matching method is introduced below) （4） For checking the image returned by the camera （5）In the advanced options, you can adjust the channels, upgrade the rocker firmware, check the signal strength, modify the receiver serial port baud rate (password needs to get from the technicians) Frequency Matching （1）When the receiver is powered on, the green light
PAGE 8
（2） Rocker Calibration H12Tool (1)Put the rocker G, H back to the center, and then turn off he remote controller (2) Long press D button to power on, and release D button after turning on the remote controller (3) When calibrating the rockers, please check the rubber capacity in the H12Tool and open the auxiliary calibration. (4) Long press D button to enter the calibration mode, and the remote controller will ring continuously.
PAGE 9
Common Questions and Solutions 1. Can other APPs be installed on the remote controller? The remote controller terminal permissions are all open, without any special software and limited software installation and unloading. 2. Data transmission cannot be connected Check whether it is connected to the remote controller at UDP type, and whether the listening port is 14551. Check whether the baud rate is normal. Check if RX TX is connected reversely (Correct way:connect RX to TX,TX to RX ). 3.
PAGE 10
FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.