User Instructions

Product List
Pager
Keypad
Pager dimension
103*51*11mm
Keypad dimension
235*155*35mm
Pager material
ABS
Keypad material
ABS
Receiving sensitivity
-114dB
Transmitting power
130mW
Standby time
Approximately 20 hours
Keypad frequency
315MHz
Pager battery
Built-in 3.7V 200mAh rechargeable
lithium battery
Power adapter
Input: AC 100-240V, 50/60Hz
Pager frequency 315MHz Output: DC 12V, 1A
Reminding method
Ring vibrate and flash
Keypress method
No touch panel
Distance of transmission
About 300 meters in a wide-open field
Modulation
AM
Brand
AGJ
Manufacturer
Wirelesslinkx
Model
6950
Protection level
IP32
Instructions
1.Charging: Before using, please connect the charging base to power,
and put the pagers in the charging slot for 10 minutes to charge.
2.Switch On Pager: Connect the charging base to power.
And put the pagers in the charging slots. Pagers will be switched on automatically.
3.Switch Off Pager: Connect the charging base to power, and put the pagers in the charging slots. Input 99 in the
keypad and call all pagers. And all pagers will be switched off.
Pagers need to be paired with keyboard transmitter first.
4. Keypad ID Setting: Press CALL and DEL at the same time, and the display will show "U". Input a number
from 01-99 to change the keypad ID. Press CALL again to save, and press DEL twice to quit and finish.
And the display will show -- . Try not to change the keypad ID. When the ID is changed,
all the pagers will be repaired to work. Keypad ID can't be 00 or 99.
5. Pager Number Setting: Take the pager off the transmitter and take away the plastic sheet and paper sticker.
There is a small round metal button on the pager front and there is a small button on the side of the pager.
Press these 2 buttons at the same time, and 2 lights will be on. These 2 lights will last for 4 seconds.
Within the 4 seconds, press a number from the transmitter from 01 - 98. Don't use number 99, because 99 is the
shut-off function. And press CALL to save the number. If you need to change the pager number,
just repeat pairing method above.
6. Pager Alarm Time Setting: Take the pager off the transmitter and take away the plastic sheet and paper sticker.
There is a small round metal button on the pager front.Use a small screw driver to press the metal button.
Each time you press the metal button, there will be one more light on the pager.
When there is one light on, the pager can ring, flash and vibrate. The prompt time is 7 seconds.
And the pager will stop ringing, flashing and vibrating automatically.
When there is two light on, the pager can ring, flash and vibrate. The prompt time is 14 seconds.
And the pager will stop ringing, flashing and vibrating automatically.
When there is three light on, the pager can ring, flash and vibrate. The prompt time is 21 seconds.
And the pager will stop ringing, flashing and vibrating automatically.
When there is four light on, the pager can ring, flash and vibrate. The prompt time is 28 seconds.
And the pager will stop ringing, flashing and vibrating automatically.
When there is five light on, the pager can ring, flash and vibrate. The prompt time is 35 seconds.
And the pager will stop ringing, flashing and vibrating automatically.
When there is NO light on, the pager can flash and vibrate, no beep. The prompt time is 10 seconds.
And the pager will stop flashing and vibrating automatically.
After pressing the metal button and changing the prompt time,
always press the small button on the pager side to save and exit.
Note: 2 and more transmitters can call one pager. Please change the transmitters' ID to the same ID number.