USER’S MANUAL WLAN Interface Module JK-W03 SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO.
JK-W03 User’s Manual Revision records Version Date Description Author records 2013-10-29 V1.0 First release Zhao Qiangqiang, Chen Qiuyi, Lv Qi Zhao Qiangqiang, Chen Qiuyi, 2014-7-3 V1.
JK-W03 User’s Manual Declaration Information in this document is subject to change without notice. SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the right to improve products as new technology, components, software, and hardware become available. If users need further data about these products, please feel free to contact SNBC or your local dealer.
JK-W03 User’s Manual Safety instructions Before operating and using the product, please read the following items carefully: 1) The interface module is a part of whole machine, and please observe the cautions in User’s Manual while using; 2) Keep this manual safe and at hand for reference purpose.
JK-W03 User’s Manual Contents 1 Overview.................................................................................................................................................................. 1 1.1 Introduction...................................................................................................................................................... 1 1.2 Main features........................................................................................................................
JK-W03 User’s Manual 1 Overview 1.1 Introduction The interface module cooperates with SNBC’s printer for using, and they are used to realize the function of printer network communication. They can carry out the Wi-Fi communication, 10/100Mbps Ethernet communication, port 9100 printing, printer status back, configuration and maintenance of interface module, and so on. 1.2 Main features 1) Features l Support 802.11b, 802.11g, 802.
JK-W03 User’s Manual 2 Main technical index Item Content Wire Wire related communication 10Mbps/100Mbps speed Wireless communication Max. 150Mbps speed If there is no obstacle in the Transmission distance room, the maximum distance is 100m (the transmission distance changes with the using Wireless related environment). Channel 1-13 64/128 WEP, WPA-PSK, Safety WPA2-PSK Network card type USB2.
JK-W03 User’s Manual 3 Appearance and modules 3.1 Appearance and modules Figure 3.1.1 Appearance of interface module 1—40P double bend socket 2 —control board 3 —antenna 4 —WIFI module 5—Ethernet communication interface (optional) 6 —reset button 7 —interface baffle 3.2 LED description The wired interface module has two LEDs, one yellow and one green.
JK-W03 User’s Manual 4 Installation 4.1 Unpacking Open the carton and check whether all items listed on the packing list are included or have any damages. In case of damages or missing items, please contact your dealer or the manufacture for assistance. 4.2 Connecting interface module Refer to Figure 4.2.1, insert the interface module into the communication interface of printer, and fix it onto the printer with screws. Then insert the network cable into the 10/100M BASE-T communication interface.
JK-W03 User’s Manual Figure 4.2.3 Self-test page information under wired mode Among which: n Interface Type: indicate type of interface. When the wireless interface is valid, it is Wi-Fi; when the wired interface is valid, it is Ethernet; n SSID: indicate the service area identifier of wireless communication; n Mode: indicate wireless mode.
JK-W03 User’s Manual 5 Device search and parameter configuration 5.1 Connecting wireless module through wireless network 5.1.1 Checking parameters of wireless module The parameters of the wireless module are the factory default values when receiving the wireless module for the first time, which can be confirmed by printing the printer self-test page. Figure 5.1.
JK-W03 User’s Manual 5.1.2 Wireless network connection with wireless module using network card Figure 5.1.2 wireless mode self-test page information If the Mode parameter of the wireless module is AD-HOC, it indicates that the wireless module is under AD-HOC mode. Under this mode, you can carry out the wireless network connection with wireless module directly using network card rather than using wireless router.
JK-W03 User’s Manual Figure 5.1.4 WIN7 system wireless network connection interface Caution: represents AD-HOC mode wireless network built by wireless module; represents Infa mode wireless network built by wireless Router. Since our wireless module is under AD-HOC mode, choose the corresponding wireless network name defaultSSID under AD-HOC mode to connect, the network marked by red lines shown in figure 5.1.4. Configure the wireless interface under AD-HOC (point-to-point) mode. 5.1.
JK-W03 User’s Manual 5.2 Search interface module through configuration tool Through the BYNetWinConfig.exe (V3.07 and above) tool, you can search the network interface modules connected to the same network, and configure and change their parameters. Before running the software, connect the host to the network that the printer is in, and set the network mode, SSID, and subnet mask of host to make them consistent with interface module.
JK-W03 User’s Manual that the user can configure and manage easily. The information displayed includes: Printer name, MAC address, IP address, gateway address, subnet mask, DHCP enabled, firmware version of interface module and interface type. Note: 1. When JK-W03 network interface adopts UDP protocol, UDP broadcast protocol, and UDP and IPX/SPX protocol for search, the IP address cannot conflict.
JK-W03 User’s Manual Click “Install” button, and the following dialog box will pop up (see Figure 5.2.3): Figure 5.2.3 Select type of network components Select “protocol”, click “Add” button and the following dialog box will pop up (see Figure 5.2.4): Figure 5.2.4 Select network protocol Select “NWLink IPX/SPX/NetBIOS Compatible Transport Protocol”, and click “OK” button to finish the installation of IPX protocol.
JK-W03 User’s Manual Figure 5.2.5 Protocol property window Through the above steps, finish the installation of IPX protocol and it can be used. n Password verifying function Select the device in list box of main window, click the “Set network parameter” button of main window and the password verifying dialog box will pop up (see Figure 5.2.6). Then enter the configuration password (there is no password in the default configuration, and click “OK” directly), and then click “OK” to verify the password.
JK-W03 User’s Manual Figure 5.2.7 Set wireless parameters window Region selection: Select different channel region and the channel range used by different regions is different. Communication mode: Select the working mode of printer wireless network. The base station mode (that is, infrastructure network) is the type that using wireless router to build the wireless network. The peer-to-peer mode (that is, AD-HOC mode) builds the wireless network directly using wireless network card.
JK-W03 User’s Manual n Set network parameters like IP address, etc. After the password verifying passes, enter the window of “Network parameter setting” (see Figure 5.2.8), then the network parameters like IP address can be changed. Figure 5.2.8 Network parameters configuring window Through this window, there are two methods to configure the network parameters. One method is “Get IP address automatically”, and the other method is to set the parameters like IP address manually.
JK-W03 User’s Manual n Interface module firmware updating Select the device in list box of main window, click “Interface firmware update” button to enter window of firmware updating (see Figure 5.2.9) and then check whether the IP address is consistent with that of selected device (compare with the self-test page printed by the device). Figure 5.2.9 Firmware updating window If their IP addresses are consistent, click “Open File” button and select the file to be updated.
JK-W03 User’s Manual 5.3 Realization of printing function Install the printer driver, and the port type selects parallel interface. After finishing the installation, configure the port of printer driver to network port again. Take BTP-2002NP printer under Windows XP system for example to explain how to configure the network port: 1) Right click the installed BTP-2002NP icon and open the property window (see Figure 5.3.1); Figure 5.3.1 Printer property window 2) Select “Port” property (see Figure 5.3.
JK-W03 User’s Manual (see Figure 5.3.3); Figure 5.3.3 Printer Ports 4) Click “Next” (see Figure 5.3.4); Figure 5.3.4 5) In relative editing box, fill in “Printer Name or IP Address”. The contents filled in should be consistent with that on the self-test page of printer, and then click “Next” (see Figure 5.3.5); Figure 5.3.
JK-W03 User’s Manual 6) The default contents (see Figure 5.3.6), and click “Next”; Figure 5.3.6 7) Refer to Figure 5.3.7, click “Finish” button to finish the adding of port; Figure 5.3.7 8) Refer to Figure 5.3.8, select the newly added TCP/IP port, click “Application” and then click “OK” button to finish the configuration of TCP/IP port. Figure 5.3.
JK-W03 User’s Manual 5.4 Firmware updating JK-W03 interface module supports updating firmware online, and the updating function is realized through TFTP protocol. Use BYNetWinConfig.exe tool to update the firmware (refer to Chapter 4.3), or you can send the firmware updating file to port 69 of interface module for updating through any TFTP client. While updating the firmware, you must adopt the firmware provided by SNBC.
JK-W03 User’s Manual Click “Printing Demo” button to connect the printer, send print data and close the connection; Click “Printer Status” button to enter status monitoring window (see Figure 5.5.2): Figure 5.5.2 Status monitoring window Click “Start Monitor” button to start monitoring the status of printer, and refer to Figure 5.5.3 for normal printer status: Figure 5.5.3 Normal printer status display If status of printer changes, the interface LED will be red.
JK-W03 User’s Manual 5.6.1 Interface Status Start Internet browser, enter IP address of printer and you can see window of interface status. Then click “Refresh” button to refresh current status (see Figure 5.6.1): Figure 5.6.1 Interface status 5.6.2 Printer Status Click “Printer Status” link to check status of printer connected to the interface. If there is abnormal status, the letters in the page will show in red.
JK-W03 User’s Manual 5.6.3 Firmware update Click “Firmware update” link and update the interface firmware through this web page (if you have set the safety password, you can enter only when you have entered correct password, see Figure 5.6.5), see Figure 5.6.3. Click “Browse” button to select the firmware needing to be updated, then click “Update” button to update the firmware. When the web page like Figure 5.6.
JK-W03 User’s Manual 5.6.4 Interface select When wired mode and wireless mode of interface module can be used at the same time, the “Interface select” link will be added to the web page. Click “Interface select” to set current network interface type (if you have set the safety password, you can enter only when you have entered correct password). If selecting “Wireless”, adopt wireless interface; If selecting “Wired ”, adopt wired interface. Figure 5.6.
JK-W03 User’s Manual through clicking “Restore Defaults” button. After changing the configuration, restart the printer to make new configuration valid. The restarting of printer can be carried out through clicking the “Reboot” button on the left, or through turning off/on the printer power. The configuration page is as follows: Figure 5.6.7 TCP/IP configuration page Note: Only letter or digit can be set as safety password and cannot use special symbols.
JK-W03 User’s Manual Figure 5.6.8 Configuration of wireless basic parameters In the “Security” page, the encryption mode and the password of wireless network can be set. Under base station mode, support WEP, WPA-PAK and WPA2-PSK; Under peer-to-peer mode, support WEP and WPANONE mode. When adopting WEP encryption, you can select “Open System” and “Shared Key” these two kinds of mode; when setting to WPANONE, WPA-PSK or WPA2-PSK, you can select “AES” and “TKIP”.
JK-W03 User’s Manual “Reboot” button on the left side or through turning on/off the printer power. Note: Don’t restart the wireless network parameters “Basic” and “Security” unless all parameters have been set. If performing the restart operation after having set partial parameters, then this may lead to abnormal connection of wireless network. 5.7 Button function and restore defaults Insert thin material into button hole of interface module (see Figure 3.1.
JK-W03 User’s Manual 6 Interface signal The wireless part adopts the USB interface WIFI module bought from outside and the main technical specifications are as follows: Item Bus type Content USB2.0 Data 11,5.5,2,1 Mbps (802.11b mode) transmission 54, 48, 36, 24, 18, 12, 9, and 6 Mbps (802.11g mode) speed Working 1-11 channel If there is no obstacle in the room, the maximum distance is Transmission 100m (the transmission distance changes with the using distance environment).
JK-W03 User’s Manual FCC STATEMENT: 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
JK-W03 User’s Manual Federal Communication Commission Statement (FCC, U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
JK-W03 User’s Manual Limited Channels fixed for use in the US: IEEE 802.11b or 802.11g or 802.11n(HT20) operation of this product in the U.S. is firmware-limited to Channel 1 through 11. IEEE 802.11n(HT40) operation of this product in the U.S. is firmware-limited to Channel 3 through 9.
