USER’S MANUAL Mobile Printer BTP-P35 Shandong New Beiyang Information Technology Co., Ltd.
BTP-P35 User’s Manual Contents 1 Introduction..................................................................................................... - 1 1.1 Outline....................................................................................................... - 1 1.2 Main features........................................................................................... - 2 2 Main technical specification......................................................................... - 3 2.
BTP-P35 User’s Manual 6 Installation printer........................................................................................ - 28 6.1 The host accessories...........................................................................- 28 6.2 Precautions for using the printer........................................................ - 28 6.3 Power cable connection......................................................................- 29 6.4 Paper roll installation..........................................
BTP-P35 User’s Manual Declaration Information in this document is subject to change without notice. SHANDONG NEW BEIYANG INFORMATION TECHNOLOGY CO., LTD. (hereinafter referred to as “SNBC”) reserves the right to improve product as new technology, components, software, and firmware become available. If users need further data about this product, please feel free to contact your dealer or the manufacturer.
BTP-P35 User’s Manual SNBC has passed the following certifications: ISO9001 Quality Control System Certification ISO14001 Environmental Management System Certification OHSAS18001 Occupational Health and Safety Management System Certification IECQ QC 080000 Hazardous Substance Process Management System Certification BTP-P35 has passed the following certifications: Warning This is class A product. The product may cause radio interference in the working environment.
BTP-P35 User’s Manual General Safety Information Before installing and using the printer, please read the following items carefully. Safety instructions Warning: Don’t touch the tear bar of printer. Warning: The print head is a thermal element and it is at high temperature during printing or just after operation. Therefore please do not touch it and its peripherals for safety reasons. Warning: To prevent static electricity damages print head, do not touch either print head or connecting parts.
BTP-P35 User’s Manual sharing a single electrical with large power motors and other devices that may cause the fluctuation in voltage. 7) The power outlet should be close to the printer for easy connection 8) Do not let the water or the electric materials (like metal) go into the printer. If this happen, turn off the power. 9) The printer cannot print in the state without paper, otherwise it will seriously damage the print head.
BTP-P35 User’s Manual -7-
BTP-P35 User’s Manual 1 Introduction 1.1 Outline BTP-P35 is a thermal mobile receipt printer with high print quality, fast speed, stable performance, long standby time and small portability. It is widely used in retail, government, law enforcement, insurance, logistics and other fields. The product is mobile printer supporting for POS, BPLC command sets, and provide characters, graphics, barcode and other printing functions.
BTP-P35 User’s Manual (Waist bag) shoulder strap, and other accessories. 1.
BTP-P35 User’s Manual 2 Main technical specification 2.1 Technical specification The parameters are under the standard test paper conditions. Model BTP-P35 mobile printer Print method Thermal Print resolution 203dpi Print width (Max.) 72mm Print speed Max.102mm/s. Factory default value is 76.2mm/s Print length 10-1000mm Paper out method Tear-off mode Memory 64MB RAM, 4MB Flash Communication interface Standard configuration : USB 2.
BTP-P35 User’s Manual 1D barcode (ESC/POS UPC-A, UPC-E, JAN13 (EAN13), JAN 8 (EAN8), command) CODE39, ITF, CODABAR, CODE93, CODE128 2D barcode (ESC/POS PDF417, QRCODE, MAXICODE, GS1 command) Plain bitmap in binary system. HEX, PCX, BMP and Graphic format IMG.
BTP-P35 User’s Manual Output voltage Working Environmental condition temperature Storage temperature Standard Accessory configuration Optional configuration 12VDC±5%, 2.
BTP-P35 User’s Manual Paper thickness: 0.06—0.1mm 2.2.2 Parameters of black marked paper The marked paper should meet the following requirements: 1) Mark position There are nine positions installed mark sensors which can detect the mark on the front or back of the paper. A to D position of sensor to detect the inner mark of the paper roll. 1 to 5 position of sensor detect the outer mark of the paper roll. The position of the sensor is shown in the figure.
BTP-P35 User’s Manual L3 space between marks: 10mm≤L3≤1000mm 3) The reflectivity of the mark part is less or equal to 15%, and the reflectivity of the other part of the paper in the direction of the paper feeding mark width is more than or equal to 85%. There should be no any pattern in the area between the two marks like advertisement.
BTP-P35 User’s Manual following table: Print Distance from the print Distance from the print width content to the left content to the right (L2) edge(L3) edge(L4) 80mm 72mm 4mm 4mm 60mm 52mm 4mm 4mm Paper width (L1) 2.3.
BTP-P35 User’s Manual 3 Appearance and components 3.
BTP-P35 User’s Manual 19——Tear-off bar 20——Reflective 21——Mechanism sensor(standard bracket configuration) 22——Platen roller pothook 23——Transmissive 24——Print head sensor 2 25——Swipe card module (optional configuration) Caution: Paper guide is an indispensable part which adjusts the width of paper. You should pay attention to the proper use. 3.
BTP-P35 User’s Manual 2A Power 1. Chinese adapter standard area use (Chinese 2. Charge the standard) printer 3. Match up a lithium battery charging cradle to charge a single lithium battery 1. US standard 2A Power area use adapter (US 2. Charge the standard) printer 3. Match lithium up a battery charging stand to charge a single lithium battery 1. UK standard 2A Power areas use adapter (UK 2. Charge the standard) printer 3.
BTP-P35 User’s Manual lithium battery 1. EU standard 2A Power area use adapter (EU 2. Charge the standard) printer 3.
BTP-P35 User’s Manual 1. Chinese AC power cord standard area use (Chinese 2. 5A Power standard) adapter AC power cord 1. US standard AC power cord area use (US standard) 2. 5A Power adapter AC power cord 1. UK standard AC power cord areas use (UK standard) 2. 5A Power adapter AC power cord 1. EU standard AC power cord area use (EU standard) 2.
BTP-P35 User’s Manual same time Vehicle-bone 1. Charge the charger printer 2.
BTP-P35 User’s Manual 4 System function and settings 4.1 Explanation of panel 4.1.1 Appearance panel 4.1.2 Button function Button Power button Function Explanation 1. On / off 2. Sleep / wake-up state 1. Enter the configuration Configuration button 1. Go to the submenu 2. Enter parameter configuration 3. Switch the parameter position 4. Confirm the configuration 5. Execute menu operation In the power on state, press [Power] button for a long time to turn off the printer.
Paper feed Pause printing Resume printing Paper feed button/ up button 1. Page up 2.Ajust parameter up Pause Pause button/Down button 1. Page down 2. The parameter is adjusted downward. BTP-P35 User’s Manual 5. When the current menu has no submenu and no parameter adjustment, the current menu operation is selected and executed Press the [Feed] button in the idle state: paper feed Press the [Feed] button in the working state: pause printing Press the [Feed] button in the pause state: 1.
BTP-P35 User’s Manual optional configuration reflective sensor, optional transmmisive sensor 3 4 Print darkness Print speed 00~30 02~04 IPS No feeding. Paper feed 5 Start when start calibration. up Fix position to label No feeding. 6 Close Start cover and calibration.
BTP-P35 User’s Manual marked paper; continuous paper 2 Left 0~49mm margin 3 Right 0~49mm margin 4 Label 0~8000 length 5 Label 0~5000 width 6 Horizontal 0~800 offset 7 Vertical 0~199 offset 8 Tear-off 0~199 position 9 Detect Enabled; paper Disabled when idle 10 Back to previous level 1 3 Paper 0~255 sensor threshold Sensor setup Code setup 2 Mark sensor threshold - 18 - 0~255
BTP-P35 User’s Manual 3 Label light 0~255 strength 4 Mark light 0~255 strength 5 Sensor Display the information information of sensor 6 Back to previous level 4 1 IP address IP address 2 Subnet Subnet mask mask WLAN configuration 3 Gateway Gateway 4 IP protocol TCP UDP 5 WLAN port WLAN port setup 6 WLAN Port information information 7 BT code 8 BT information 9 Back to previous level 5 1 Other configurations Sleep time 10~60s 2 The time of Not power off automat
BTP-P35 User’s Manual 3 4 5 6 7 Language Chinese setup English Command ESC/POS language BPLZ/BPLE Buzzer High volume Low Button On buzzer Off USB mode API mode Class mode 2 3 4 5 6 Factory reset Reset outgoing parameter 7 Save /Exit Whether save the current setup or not Print Printer information output self-test Print calibration Calibrate the current light strength of sensor Cancel print Cancel caching data of printing Exit Exit menu 4.
BTP-P35 User’s Manual Use the “Up / Down” button to select the “Setup” menu item. Print mode Set the print mode in the “Setup / Print setup / Print mode Setup” menu item. Use the “Up / Down” button to select the mode. Optional modes are “tear-off mode”, “rewind mode”. Print darkness setup Set the print darkness in the “Setup / Print Setup / Print darkness” item. Use the “Setup” button to select the ones place and the tens place. The Up / Down button to increases or decreases the darkness value.
BTP-P35 User’s Manual Paper type selection In the menu "Setup / Paper setup / Paper type", set the current paper type. The optional type: "continuous paper", "marked paper". Wireless configuration In the "Setup" menu item, select "Setup / Wireless configuration", you can set the printer's network configuration. Such as a protocol type, IP address configuration, gateway configuration, and port configuration.
BTP-P35 User’s Manual System language type setup In the "Configuration / Other Configuration / Language Setup" menu item, set the system language type Command set type selection In the "Configuration / Other Configuration / Command Language" menu item, set the command language type System sleep time setup In the "Configuration / Other configuration / Sleep time" menu item, set sleep status. When enabling sleep, enter the sleep delay time. Delay time is10m~60m.
BTP-P35 User’s Manual When the paper roll is loaded in the paper cabinet, a print calibration is made. The paper and sensor calibration are made. Press the "Setup" button to enter the first level menu, and select "print calibration" to set. Status explanation of the printer Status explanation LCD Print status Charging status Open the paper cabinet Paper end status NO print head 4.
BTP-P35 User’s Manual Status Explanation Music when starts up Prompt music of on and off Ring for a long time The printer has a fatal error. Ring for a short time 1. The printer has a general error or an alert 2. The button prompt sound Caution: The printer adopts thermal resistor to detect the temperature of print head. If the print head temperature is too high, the printer will stop printing. 4.5 Swipe card function The BTP-P35 supports magnetic card and IC card swipe function.
BTP-P35 User’s Manual 5 Printer communication interface This BTP-P35 can be connected via USB, WIFI interface and other devices. 5.1 USB interface USB interface supports USB1.1 protocol. The interface socket using MINI USB B-type standard socket: Interface signal definition: Pin Cable 1 VCC 2 DATA- 3 DADA+ 4 ID 5 GND 5.2 WIFI interface 1) Features Support 802.
BTP-P35 User’s Manual Support HTTP function 2) Support protocols IP ARP ICMP TCP UDP DHCP TFTP HTTP - 27 -
BTP-P35 User’s Manual 6 Installation printer 6.1 The host accessories This product configures with standard power adapter, belt clip, USB cable and other accessories, and optional configuration is magnetic card/IC POS machine point of sale machine, battery charger, vehicle-bone charger, IP54 protective cover, shoulder strap and other accessories. When unpacking, check the packing list whether has the missing or damaged items.
BTP-P35 User’s Manual 6.3 Power cable connection 1) Pin definition 1: Positive (+12V) 2: Negative (GND) 3: Negative (GND) 2) Interface type Printer usage: socket in the following figure in the left User usage: socket in the following figure in the right As shown in the figure, insert the power adapter plug into the power socket, DC plug into the printer’s charging interface.
BTP-P35 User’s Manual Input voltage: AC100-240VAC / 50 ~ 60Hz Caution: Do not remove the battery during charging; When charge the battery, the printer can print task. Should use the manufacturer recommended power adapter or its equivalents; When plugging the plug of power adapter, you should hold the connector cover of the plug, do not pull the cable; Avoid dragging the power adapter cable, or it will damage the cable and cause fire disaster and electric shock.
BTP-P35 User’s Manual 6.4 Paper roll installation 6.4.1 Confirmation of printing paper Before installing the paper roll, you should first check the paper type used by the printer. The default paper type is continuous paper. If you need to set marked paper, please calibrate it. 6.4.2 Install / replace the paper roll 1) Press the [Open] button of paper top cover, open the top cover. 2) Hold the paper guide and rotate it upward and forward, then uninstall it .
BTP-P35 User’s Manual Remarks: When the printer is printing, the paper guide should center the paper roll in the paper cabinet. 4) Make sure the paper head is flush and place the paper roll in the paper cabinet as shown in the figure below. After pulling out the paper head for a distance along the direction of paper out, close the back cover and tear off the excess paper head. Then finish installing paper roll.
BTP-P35 User’s Manual The paper roll should be wrapped tightly. Otherwise, it may cause paper jam or other errors. The paper roll should be placed in the paper house smoothly, avoid tilt, otherwise it may affect the printing and paper feeding; The edge of the paper head cannot deviate from the paper out exit. 6.5 Printer connecting installation When the printer is leaving the factory, the default connection is the belt clip.
BTP-P35 User’s Manual 6.5.2 Shoulder strap connection (optional configuration) When the printer is leaving the factory, the shoulder strap is not installed in the printer. Please install the shoulder strap in the printer according to the figure. 6.6 Printer power on and self-test 6.6.1 Power on the printer 1) Make sure the printer battery is fully charged and install in place; 2) Press the [power] button for more than two seconds. The printer will turn on and initialize. 6.6.
BTP-P35 User’s Manual 3) Press "Up" or "Down" to select "2. SELFEST" or "2.SELFTEST" and press CONFIRM to confirm; 4) The printer begins printing the self-test page. 6.7 Connect the communication interface BTP-P35 has two communication modes: Wired communication: USB interface Wireless communication: WIFI; 6.7.1 USB interface connection 1) Insert the USB interface cable into the suitable interface; 2) Connect the other end of the interface cable to the host. 6.7.2 WIFI connection See appendix 9.
BTP-P35 User’s Manual 7 Routine maintenance Caution: Before starting routine maintenance, ensure that turn off the printer Do not use organic solvents like gasoline or acetone. When cleaning the sensors, do not turn on the printer power until the pure alcohol has completely evaporated. It is recommended that the maintenance cycle should not be longer than one month. 7.1 Cleaning print head and platen roller When any of the following cases occur, the print head and platen roller should be cleaned.
BTP-P35 User’s Manual to wipe off the dust and stains on the surface of the print head and platen roller when the top cover of the paper cabinet is open; 4) Close the top cover of paper cabinet after the neutral cleaner evaporates completely. 7.2 Cleaning marked sensor When any of the following cases occur, the marked sensor should be cleaned. 1) The printer alarms the paper end during printing. 2) The printer does not alarm when paper end. 3) The printer cannot read the mark effectively.
BTP-P35 User’s Manual 8 Troubleshooting When the printer has any problem, refer to this chapter for solution. If the problem still cannot be solved, please contact your local dealer or manufacturer for assistance. 8.1 Printer doesn’t work Problem The printer does not work. Possible causes The battery has no power. The battery does not connect well. Circuit board is damaged. Solution Please charge the battery or replace the battery. Take out the battery and re-install it.
BTP-P35 User’s Manual 8.3 Problems during printing Possible Problem Paper continuously Solution causes feed when printing Paper cannot be sent out normally. Wrong paper type Marked sensor errors Paper jam Vertical print content is Print head missing. error Replace with matched paper roll Contact your local dealer or manufacturer. Open the top cover, check the paper feeding path and clear the jammed paper. Contact your local dealer or manufacturer.
BTP-P35 User’s Manual 9 Appendix 9.1 Printer driver installation on windows BTP-P35 provides Windows 2000/Windows XP/Windows Server 2003/Windows Vista/Windows Server 2008/2012/Windows 7/Windows 8/ Windows 10 operating systems drivers. 9.2 WIFI connection 1) Connect the BTP-P35 printer with windows system via WIFI. Turn on the Internet setup tool of windows system 2) After turning on successfully, read the right parameter of WIFI; 3) Click “on” to set communication mode, such as infrastructure mode.
BTP-P35 User’s Manual - 41 -
BTP-P35 User’s Manual - 42 -
BTP-P35 User’s Manual FCC STATEMENT : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.