User Manual Product Name: Core board module4G Model Name: ABSL-G, XY6762CA-C Brand Name: SHADOW Manufacture: ABSOLUTE SOLUTION CO.
1 product description 1.1Absl-g is a chip module with 166lcc pins. The size is only 40.5mm × 50.5mm × 85mm, which can be embedded in all kinds of M2M products through pad. It is very suitable for the development of mobile devices such as on-board computer, multimedia terminal, smart home, Internet of things terminal, etc. 1.2This document defines the hardware interface specification, electrical characteristics and mechanical specifications of absl-g module.
P22) platform, industrial high performance, and can run Android 9.0 operating system. The hardware of the module is compatible with each other, supporting LTE / WCDMA / TD-SCDMA / EVDO / CDMA / GSM and other standards; It supports WiFi 802.11 a / B / g / N / AC, BT v2.1 + EDR, 3.0 + HS, v4.1 + HS, V5.0, Beidou, Galileo, GLONASS, GPS, QZSS satellite positioning; It has multiple audio and video input and output interfaces and rich GPIO interfaces.
Characteristics of GSM / GPRS / edge EDGE： WLAN features Support edge multi slot class 12 Bluetooth features Support GMSK and 8PSK satellite positioning Coding format: cs1-4 and MCS 1-9 EMMC 2.4ghz/5ghz dual band, support 802.11a/b/g/n/ac, up to 150Mbps DDR Support AP mode SDIO interface Support SD / SDHC / MS / mspro / MMC / sdio2.0 or 3.
3. Power supply 3.1.Power interface The input range of absl-g power supply is 3.45v-4.35v, and the recommended value is 4.0V. The performance of Vbat power supply, such as load capacity, ripple size, etc., will directly affect the performance and stability of the module. Under the limit condition, the module current consumption may reach the instantaneous peak value of about 3a, and if the power supply capacity is insufficient, there will be voltage drop. If the voltage drops below 3.
图 6：Open set drive reference power on circuit Another way to control the pwrkey pin is directly through a button switch. A TVS should be placed near the button for ESD protection. The reference circuit is as follows: 图 7：Key start reference circuit 3.2.2 Power off Power off can be achieved by lowering the pwrkey signal for at least 2 seconds. After the module detects the shutdown action, a prompt window will pop up on the screen to confirm whether to execute the shutdown action.
图 9：sequence diagram 4. Storage and production Absl-g is packaged in the form of vacuum sealed bag, and the storage of the module should follow the following conditions: 1. When the ambient temperature is lower than 40 ℃ and the air humidity is less than 90%, the module can be stored in a vacuum sealed bag for 12 months.
FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
OEM INTEGRATION INSTRUCTIONS: This device is intended only for OEM integrators under the following conditions: The module must be installed in the host equipment such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna. The module shall be only used with the internal on-board antenna that has been originally tested and certified with this module. External antennas are not supported.
FCC MODULAR APPROVAL INFORMATION EXAMPLES for Manual This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Requirement per KDB996369 D03 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules (Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.
2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ – Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements. a) Information that includes permitted variances (e.g.
2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an “omni-directional antenna” is not considered to be a specific “antenna type”)).
2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
