User's Manual

ManualsBrandsSGS Activos ManualsElectronicsMovement Sensor Device

USER MANUAL

1/(7)

Title:

SWH - Movement Sensor Device - Installation and configuration Manual

Prod. #

010103

Doc. #

Rev:

Summary:

Installation and configuration Manual of Movement Sensor Device

Date:

16/03/2022

Author:

SMV

Review:

SGS - IOT COMPETENCE CENTER

This document and information contained in it are confidential and are the property of Société Générale de Surveillance (SGS). They may not in any

way be disclosed, copied, or used by anyone except as expressly authorized by SGS. The document should always be kept in a secure place and

should be destroyed or returned to SGS when it is no longer needed.

TITLE

SWH - Movement Sensor Device - Installation and configuration Manual.

SUMMARY

Installation and configuration Manual of Movement Sensor Device.

PURPOSE OF THIS DOCUMENT

This document describes the user manual to perform the installation and configuration of the Movement Sensor Device.

HISTORY OF THE DOCUMENT

Rev.

Author

Date

Description

SMV

16/03/2022

User manual to install and configure Movement Sensor Device

Summary of content (7 pages)

PAGE 1
USER MANUAL Title: SWH - Movement Sensor Device - Installation and configuration Manual Summary: Installation and configuration Manual of Movement Sensor Device 1/(7) Prod. # Doc. # Rev: Date: Author: Review: 010103 03 A 16/03/2022 SMV TITLE SWH - Movement Sensor Device - Installation and configuration Manual. SUMMARY Installation and configuration Manual of Movement Sensor Device.
PAGE 2
Prod. # 010103 Doc. # 03 Rev A SWH - Movement Sensor Device - Installation and configuration Manual 2/(7) Date 16/03/2022 Author SMV INDEX TITLE .................................................................................................................................................................................... 1 SUMMARY...........................................................................................................................................................................
PAGE 3
Prod. # 010103 Doc. # 03 Rev A SWH - Movement Sensor Device - Installation and configuration Manual 3/(7) Date 16/03/2022 Author SMV 1 PRODUCT INTRODUCTION Movement Sensor Device is a device designed to measure parameters that detect possible movement in the grain and generates an alarm. The device consists of a board with an accelerometer that transmits data via LoRaWAN technology. The main purpose of the device is to obtain these acceleration values when the device moves.
PAGE 4
Prod. # 010103 Doc. # 03 Rev A SWH - Movement Sensor Device - Installation and configuration Manual 4/(7) Date 16/03/2022 Author SMV 2.1 INSTALLATION To carry out the installation of the device, perform the following steps. 1. Checklist Unpack the package, check the part list to ensure nothing is missing. 2. Activate the device By default, the device is deactivated. To activate it, pass the magnet for 3 seconds in the reed area (one beep per second will be generated).
PAGE 5
Prod. # 010103 Doc. # 03 Rev A SWH - Movement Sensor Device - Installation and configuration Manual 5/(7) Date 16/03/2022 Author SMV 4.2 DOWNLINK COMMANDS TO CHANGE THE CONFIGURATION It is possible to change the configuration of the device through the LoRa gateway via downlink frames. You can check if the downlink has been correctly sent because the led will light up blue. The following are the different payloads for the GCM v3 device: 1.
PAGE 6
Prod. # 010103 6. Doc. # 03 Rev A SWH - Movement Sensor Device - Installation and configuration Manual 6/(7) Date 16/03/2022 Author SMV Change ACK To disable or enable the ACK send by the gateway screen you have to send 1 byte (00 / 01) respectively on Port 9. 7. Test To show the downlink message via UART send the ‘x’ bytes on Port 10. 8. Accelerometer configuration To configure the accelerometer you have to send 4 bytes (according to the table) on Port 11. 9.
PAGE 7
Prod. # 010103 Doc. # 03 Rev A SWH - Movement Sensor Device - Installation and configuration Manual 7/(7) Date 16/03/2022 Author SMV 5 SAFETY PRECAUTIONS Follow the next safety instructions: • Never submerge the device in any liquid. • Keep the device in a dry place and away from any liquids that might spill. • Do not let the electronic parts come into contact with any steel elements, to avoid injuries and burns. • The gateway must not be modeled in any way.