MODEL : LK-P41B 02%,/( 35,17(5 All specifications are subject to change without notice
1. Unpacking Table of Contents Standard 1. Product overview 3 2. Unpacking 3. Usage and Installation 5 3-1. Control panel usage 5 3-2. Battery Installation 6 3-3. Battery charging 7 3-4. Battery charger usage 8 3-5. Roll paper installation 9 3-6. Leather case usage 10 3-7. Self test 11 4. Peripherals connection 13 4-1. Bluetooth connectiontion 13 4-2. Interface cable connection 14 5. Printer specification 15 5-1. Specification 15 6.
2. Product overview 3. Usage and Installation 3-1 Control panel usage Open Button Paper feed button Power switch USB SERIAL Battery DC Power Button Name function Power button This button is used to turn the printer on and off. When the printer is off, press this button for approximately 3 seconds and it will turn on the power. When you press this button in a state that the printer is on, the printer will turn off.
3-2 Battery Installation 3-3 Battery charging Hook 1. Be sure that the printer is turned off 2. After open the DC JACK cover, insert DC JACK into the printer. 3. Plug the power code to electrical outlet. 1. Align battery hook as shown in the picture 2. Push the battery into the printer until it locks in place.
3-5 Roll Paper installation 3-4 Battery charger usage Optional DC Jack lamp 1. Insert the battery into the battery holder as shown above 2. Connect the DC JACK to the power electrical outlet. 3. Plug the power code into the electrical outlet. 4. Once the charging is completed, remove the battery from the holder.
3-6 Leather case usage 3-7 Self Test Optional Open the leather case Place the printer into the leather case 1 2 3 Turn off the power pressing the power button for approximately 3 seconds. While you are pressing the FEED button, press the power button 1 2 3 NOTE 1. To print ASCII pattern additionally, press the Feed button once more 2. After printing ASCII pattern, the self test will be finished automatically. 3.
4. Peripherals connection This printer can communicate with Peripherals device via Bluetooth and cables. 4-1 Bluetooth Connection 1. Printer can be connected to the PDA and PC which can do wireless communication. 2. By using Bluetooth function supported in PC, printer can be connected.
5.
6. CPCL Command Compatibility /05& Battery Charger Size Battery type Li-ion output 7.4V, 2200mAh Charging time 3 hour 40 minute W X D X H(mm) 149 X 161 X 69 W X D X H” 5.8 X 6.3 X 2.7 Weight Temperature Humidity 16 0.53kg (With Battery) operation -10 ~ 50Ⳅ storage -20 ~ 60Ⳅ operation 35 ~ 95% Compatible with only Partially Compatible commanders provided Compatible by the manufacturer.
18 Graphics Compatibility BOX ⷃ LINE ⷃ INVERSE-LINE ⷃ PATTERN ⷃ GRAPHICS ⷃ PCX ⷃ Advanced Commands Compatibility CONTRAST ⷃ TONE ⷃ JUSTIFICATION ⷃ PAGE-WIDTH ⷃ PACE ⷃ NO-PACE ⷃ WAIT ⷃ REWIND 9 TENSION 9 SPEED ⷃ SETSP ⷃ ON-OUT-OF-PAPER 9 ON-FEED ⷃ PREFEED ⷃ POSTFEED ⷃ PRESENT-AT 9 COUNTRY/CODE PAGE ⷃ FORMAT FILES ⷃ BEEP ⷃ CUT
7. Setting up the software Please refer to the programming manual included in CD. ǁCertification FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions: (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION Antenna shall be mounted in such a manner to minimize the potential for human contact during normal operation.
SEWOO TECH CO.,LTD. ADDRESS Doosung Bd, 689-20, Kumjung-dong, Kunpo-si, Kyunggi-do, Korea TEL 82-31-459-8200 FAX 82-31-459-8880 URL http://www.miniprinter.com Rev. 1.