MODEL : LK-P11W MOBILE PRINTER All specifications are subject to change without notice
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
1. Product overview Table of Contents 1. Product overview 3 2. Unpacking 4 3. Installation & Usage 5 3-1. Battery Installation 5 3-2. Battery Charging 6 3-3. Belt Strap Usage 7 3-4. Separation of Battery from the printer 8 3-5. Shoulder Strap Usage 9 3-6. Leather case Usage 10 3-7. Loading the paper 11 3-8. Control Panel Usage 12 3-9. Self Test 13 4. Peripherals Connection 2 Paper feed button Cover open button CHARGER CONNECTOR Battery 15 4-1. Wifi(802.
3. Setting Up the Product 2. Unpacking 3-1. Installing battery Standard Printer Battery Belt Buckle Push the Open to the direction as pointed by arrow in the image. Recharger Roll paper USB Shelded Cable CD Serial Cable Open the battery cover and push up the hook to the direction as above. 1 2 3 Quick Manual Option Insert the battery inside printer as shown. Close the battery cover once you inserted the battery completely.
3-2. Battery Charging 3-3. Belt Hook Usage Insert the belt hook screw into the hole of the belt hook. 1. The battery can be charged only when the temperature is 0~40℃ 2. Be sure that the printer is turn off and the battery to be charged is installed. 3. Connect the charger to the printer. 4. Recharging will now be started. 1 2 Notes: 1. Do not turn on the printer power while you are charging the battery. 2. Do not print while charging the battery 3.
3-4. Removing battery 3-5. Shoulder Strap Usage Push up the hook after opening the battery cover. Push the Open into the direction indicated with the arrow in the image. 1 2 3 Pull out the battery as shown above. 8 Place the end of strap into the hook of shoulder strap. Insert the strap into the hook on the printer. 1 2 3 4 After pulling out the end of strap tightly, put it into the clip to be fastened. Fasten the strap in the opposite side with the sample way.
3-6. Leather Case Usage 3-7. Loading the media. Open the Velcro 1 2 3 Put the printer into the leather case following the direction shown in the Press the cover open button and open 1 2 3 4 Place the paper roll as shown. Make sure the paper is placed in right direction. Close the Velcro Pull a short length of paper out of the printer and close the cover. 10 Press Feed button and let the paper be arranged property for printing.
3-8. Control Panel 3-9. Self Test You can check the printer setting state by doing self test when you set the printer first time or encounter some problems. - Control Circuit, Mechanisms, Print Quality, Rom version. When you can not find the exact cause of problem through self test, investigate on other hardware parts or software. This function is independent of other devices and software. ● Self –Test Instructions Button 12 Name function Power button This button is used to turn the printer on and off.
4. Peripherals Connection < Sample Printout of Self Test > This product can communicate with other devices via Wi•(802.11b/g) communication and cable. 4-1. Wifi(802.11b/g) Connection 1. The Printer can be connected to devices equipped with wi•(802.11b/g) communication capacity (PDAs, PCs, etc.) 2. Use the wi•(802.11b/g) connection function supported by the device to connect to the printer. Notes: Refer to the wi•(802.11b/g) Manual for more details on connection.
5. Printer cleaning 4-2. Interface Cable Connection If the interior of the printer is dusty, printing quality can lowered. In such a case, follow the instructions below to clean up the printer. NOTE 1. Make sure to turn the printer power off prior to cleaning 2. Regarding print head cleaning, as the print head sets very hot during printing, turn off the printer power and wait approximately 10 minute before commencement. 3.