1.1 Key Features ................................................................................................................................................ 4 2.1 Front, Side and Top View ............................................................................................................................. 5 2.2 Upper Surface .............................................................................................................................................. 5 2.3 Side View..............
8.1 Applied Standards ...................................................................................................................................... 18 8.2 Declaration.................................................................................................................................................
The Access Point AP-2010 by imagotag is a network device similar to WLAN access points that is required for communication with the imagotag electronic shelf labels (transmits price information to the labels). Up to 10 000 labels can be managed per access point and the self-organizing network allows automatic roaming of labels without manual handling. The high transmission rate of the 2.
Front, side and top view of the AP-2010 Mounting plate fixation screwhole Antenna socket LED Antenna Top view of the imagotag AP-2010 Connection for the Power Supply Reset LAN/PoE unused Console
Side view of the imagotag AP-2010 Antenna Connector (unused) Snap Connector Housing Warranty Seal Rear view of the imagotag AP-2010 Mounting Tab Snap Connector Housing Mounting Rail Housing Screw Locking Tab Mounting Profile Label
Color Description Note Red Boot process Error Can take about 2 minutes, if it takes much longer, the device is defective and there is a need for service.
Kanal Frequenz 0 2404 MHz 1 2010 MHz 2 2422 MHz 3 2425 MHz 4 2442 MHz 5 2445 MHz 6 2462 MHz 7 2470 MHz 8 2474 MHz 9 2477 MHz 10 2480 MHz WLAN Kanal (802.
Sunny Computer Technology Europe s.r.o. Model: SYS1449-1505-W2E Input: 100-240 V ~ 1.0 A MAX, 50-60Hz Output: 5V 3A Output Power: 15W MAX Operating Temperature: 0° C to + 45° C Dimension (mm): 72.
The AP-2010 comes with an AP-ID, P/N, MAC and S/N. The AP-ID consists of 5 decimal digits (0-9).
Power: External Power Supply: 5 VDC / 3A Power Supply via PoE: IEEE 802.3af, IEEE 802.3at Power consumption: 15W MAX, typical 3W Technology: Radio technology: proprietary Operating frequency: 2.4 GHz (ISM-Band) – 2.4835 GHz Transmitted power: ≤ 10 dBm Number of Channels: 11 Access protocol: proprietary Power consumption measurements indicate that the AP-2010 has the following patterns: Operating Current: ≤ 60 mA (max.
The Access Point could be mounted on a: Concrete wall Mortar wall T-Mounting Rail Screw of the Antenna Front Part Direction of Rotation Connection Socket Rear Part (Swiveling) Note: Screw the antenna with only the front part (1) Once the metal bracket is mounted, the AP-2010 will be mechanical connected and fixed with a fixing screw.
Wall or Ceiling Mounting (Scheme) Mounting Surface imagotag AP-2010 Metal Bracket Fixation Screw Mounting Screw a. Install the metal bracket to the wall or ceiling with the help of dowels and mounting screws. imagotag AP-2010 Locking Tabs b. Slide the access point to the mechanical lock of the locking tabs c.
Attach the metal bracket using the included “caddy® clips” from Erico® and the enclosed, self-locking screw nuts M6. Mounting an AP-2010 on a T-Mounting Rail a. b. c. d. e.
Turned OFF: Temperature: -20° C to + 70° C Humidity: 10% to 85% (non-condensing) Turned ON: Temperature: 0° C to + 40° C Humidity: 10% to 80% (non-condensing) Temperature: -20 °C to + 70 °C Humidity: 10% to 85% (non-condensing) Steps: 1) Shutdown Access Point 2) Plug Out Power Supply (AC or PoE) 3) Clean the Access Point with the help of a damp cloth Note: Do not use liquid or aerosol cleaners.
DIMENSIONS LENGTH WIDTH STACKING QUANTITY HEIGHT 520 350 260 LAYER / UNIT 3 SETS / BOX 10 PALLET 1200 800 140 BOXES / LAYER 4 SETS / LAYER 40 UNIT 1200 800 960 BOXES / UNIT 12 SETS / UNIT 120 BOX Imagotag AP-2010 / Box: 10
You can choose between the following offered packages & accessories of the AP-2010: Article Number Model Description 120002 AP-2010 AP-2010 incl. Antenna 120003 AP-2010 AP-2010 Bundle incl. Antenna and PSU (EUR) 120004 AP-2010 AP-2010 Bundle incl. Antenna and mounting plate 120008 AP-2010 AP-2010 Bundle incl.
Housing, board and the display of the imagotag AP-2010 conform with the ROHS Directive The product meets the EU safety, health and environmental protection requirements and has the approval of CE marking Information Technology Equipment EN 60950-1/A2:2013 UL 60950-1/A2:2014 CSA CAN/CSA-C22.2 NO.60950-1-07 EMV EN 301489-17 V2.2.1 R&TTE EN 300328 V1.8.
Don't drop it. Keep it away from water. Don’t use the AP-2010 with defective parts. Don’t use the AP-2010 with spare parts and accessories which are not examined and approved by the imagotag GmbH. Unauthorized changes or modifications to the electronic label and their components without the consent of imagotag GmbH are not allowed. Don't throw defective batteries into the dustbin. Give them to a reprocessing company. Don't throw AP-2010 into the dustbin. Give them to a reprocessing company.