SERVIS 2160 BOOM ROTARY MOWER Published 06/11 Part No. 00765708C OPERATOR’S MANUAL This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01Cover RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com © 2011 Alamo Group Inc. $0.
To the Owner/Operator/Dealer This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the implement at all times. A Manual canister is provided on the implement where this manual can be properly stored. If you lose or damage this manual a free replacement manual can be obtained from an authorized Rhino dealer or by down loading the manual from the Rhino website www.servis-rhino.
In order to reduce accidents and enhance the safe operation of mowers, Alamo Group Ag Division, in cooperation with other industry manufacturers has developed the AEM/FEMA Industrial and Agricultural Mower Safety Practices video and guide book. The video will familiarize and instruct mower-tractor operators in safe practices when using industrial and agricultural mowing equipment.
Alamo Group Ag.
DEALER to CUSTOMER Pre-Delivery / Operation Instructions Dealer should inform the Purchaser of this product of Warranty terms, provisions, and procedures that are applicable. Dealer should also inform the Purchaser to review the contents of the Operator’s Manual including safety equipment, safe operation and maintenance, to review the Safety Signs on the implement (and tractor if possible) and of Purchaser’s responsibility to train his/her operators in safe operation procedures.
TABLE OF CONTENTS SAFETY SECTION .............................................................................................................. 1-1 GENERAL SAFETY INSTRUCTIONS AND PRACTICES ................................................................................. 1-2 Operator Safety .................................................................................................................................................. 1-3 CRUSHING HAZARDS ....................................................
Blade Bolt Inspection ....................................................................................................................................... 4-19 DRIVING THE TRACTOR AND IMPLEMENT ................................................................................................. 4-22 Starting the Tractor .......................................................................................................................................... 4-23 Brake and Differential Lock Setting ...........
SAFETY SECTION Safety Section 1-1 © 2011 Alamo Group Inc.
SAFETY GENERAL SAFETY INSTRUCTIONS AND PRACTICES SAFETY A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death.
SAFETY Operator Safety • READ, UNDERSTAND and FOLLOW Operator's Manual instructions, Warnings and Safety Messages. • WEAR SAFETY GLASSES, safety shoes, hard hat, hearing protection and gloves when operating or repairing equipment • WEAR appropriate breathing respirator when operating in dusty conditions to avoid respiratory diseases. • DO NOT WEAR loose clothing or jewelry to avoid rotating parts entanglement injury. • DO NOT USE DRUGS or ALCOHOL before or while operating equipment.
SAFETY SAFETY CRUSHING HAZARDS TO AVOID SERIOUS INJURY OR DEATH FROM FALLING OFF TRACTOR, EQUIPMENT RUN OVER, ROLLOVER AND CRUSHING BY FALLING WING OR IMPLEMENT: • • • • USE ROPS and SEAT BELT equipped tractors for mowing operations. KEEP ROPS lock in up position. ALWAYS BUCKLE UP seat belt when operating tractor and equipment. ONLY OPERATE tractor and equipment while seated in tractor seat. WHEN RAISING BOOM MOWER: • • • Raise or lower ONLY WHILE SEATED in tractor seat with seat belt buckled.
SAFETY CONNECTING OR DISCONNECTING IMPLEMENT SAFETY WHEN connecting mower head to the boom: • KEEP BYSTANDERS AWAY from tractor and mower. • Ensure there is enough room to lift and swing the boom with out hitting objects BEFORE connecting and disconnecting the mower head or boom: • STOP TRACTOR ENGINE, place transmission into park, engage parking brake and remove key. WHEN connecting and disconnecting the mower head or boom: • DO NOT crawl or walk under raised mower head or boom.
SAFETY SAFETY THROWN OBJECTS HAZARDS ROTARY MOWERS CAN THROW OBJECTS 300 FEET OR MORE UNDER ADVERSE CONDITIONS. TO AVOID SERIOUS INJURY OR DEATH TO OPERATOR OR BYSTANDERS FROM THROWN OBJECTS: • KEEP bystanders 300 feet away STOP MOWING IF PASSERSBY ARE WITHIN 300 FEET UNLESS: • • • • • All THROWN OBJECT SHIELDING including, Front and Rear Deflectors, Chains Guards, Steel Guards, Bands, Side Skirts and Skid Shoes in place and in good condition when mowing.
SAFETY THROWN OBJECTS HAZARDS (Continued) • DO NOT exceed mower's rated Cutting Capacity or cut non-vegetative material. • USE ENCLOSED TRACTOR CABS when two or more mowers are operating in mowing area. • Do Not mow in areas where bees or insects may attack unless you WEAR PROTECTIVE CLOTHING or use enclosed tractor cab. • ADJUST mower head close and parallel to ground without exposing blades.
SAFETY SAFETY RUN OVER HAZARDS TO AVOID SERIOUS INJURY OR DEATH FROM FALLING OFF TRACTOR OR EQUIPMENT RUN OVER: • USE ROPS and SEAT BELT equipped tractors for mowing operations. • KEEP ROPS locked in UP position. • ONLY start tractor while seated in tractor seat. • ALWAYS BUCKLE UP seat belt when operating tractor and equipment. • ONLY OPERATE tractor and equipment while seated in tractor seat. • NEVER ALLOW RIDERS on tractor or implement.
SAFETY PTO ENTANGLEMENT HAZARDS STAY AWAY and KEEP hands, feet and body AWAY from rotating blades, drivelines and parts until all moving elements have stopped. • STOP, LOOK and LISTEN before approaching the mower to make sure all rotating motion has stopped. • ROTATING COMPONENTS CONTINUE to ROTATE after the PTO is shut off.
SAFETY SAFETY MOWER BLADE CONTACT HAZARDS KEEP AWAY FROM ROTATING BLADES TO AVOID SERIOUS INJURY OR DEATH FROM BLADE CONTACT: • • • • • STAY AWAY and KEEP HANDS, FEET and BODY AWAY from rotating blades, drivelines and parts until all moving elements have stopped. DO NOT put hands or feet under mower decks STOP rotating BLADES disengage mower switch and PTO and wait for blade to stop rotating before raising mower head. DO NOT approach Sickle Bar head until Tracto Engine has been shut off.
SAFETY HIGH PRESSURE OIL LEAK HAZARD • • DO NOT OPERATE equipment with oil or fuel leaks. KEEP all hydraulic hoses, lines and connections in GOOD CONDITION and TIGHT before applying system pressure. • RELIEVE HYDRAULIC PRESSURE before disconnecting lines or working on the system. • REMOVE and replace hose if you suspect it leaks. Have dealer test it for leaks. HIGH PRESSURE FLUID LEAKS CAN BE INVISIBLE.
SAFETY SAFETY ELECTRICAL & FIRE HAZARDS TO AVOID SERIOUS INJURY OR DEATH FROM ELECTRICAL CONTACT WHEN WORKING AROUND ELECTRICAL POWER LINES, GAS LINES AND UTILITY LINES: • INSPECT mowing area for overhead or underground electrical power lines, obstructions, gas lines, cables and Utility, Municipal, or other type structure. • KEEP all raised wings at a 10 feet or greater distance from all power lines and overhead obstructions.
SAFETY TRANSPORTING HAZARDS • KEEP transport speed BELOW 20 mph to maintain control of equipment. • REDUCE SPEED on inclines, on turns and in poor towing conditions. • DO NOT TOW with trucks or other vehicles. • USE only properly sized and equipped tractor for towing equipment. • FOLLOW all local traffic regulations. TRACTOR REQUIREMENTS FOR TOWING OR TRANSPORTING IMPLEMENTS: • ONLY TRANSPORT with tractor with ROPS in the raised position.
SAFETY SAFETY HAZARDS WITH MAINTENANCE OF IMPLEMENT AVOID SERIOUS INJURY OR DEATH FROM COMPONENT FAILURE BY KEEPING IMPLEMENT IN GOOD OPERATING CONDITION IN PERFORMING PROPER SERVICE, REPAIRS AND MAINTENANCE. BEFORE PERFORMING SERVICE, REPAIRS AND MAINTENANCE ON THE IMPLEMENT: • STOP ENGINE AND PTO, engage parking brake, lower implement, allow all moving parts to stop and remove key before • • • • • • • • • • • • • • • • dismounting from tractor.
SAFETY PARTS INFORMATION PARTS INFORMATION Rhino mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to Rhino specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance, void warranties, and present a safety hazard. Use genuine Rhino mower parts for economy and safety.
SAFETY SAFETY ITEM PART NO. QTY. TYPE DESCRIPTION 1. 2. 3. 4. 5. 6. 03200347 D681 D644 D645 00776031 00765708C 1 1 1 1 1 1 REFLECT INSTRUCT INSTRUCT INSTRUCT ----------------------------- SMV Boom Mower Safety Booklet Blue Dot Decal Red Dot Decal Manual Canister Rear Mount Operator’s Manual 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY ITEM PART NO. QTY. TYPE DESCRIPTION 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16.
SAFETY SAFETY ITEM PART NO. QTY. LEVEL DESCRIPTION 1. D626 2 WARNING Thrown Object Hazard 2. D561 1 WARNING Use Genuine Rhino Parts 3. D565 1 DANGER Crushing Hazard 4. D666 1 lNSTRUCT Lubrication Chart 5. D619 1 WARNING Blade Rotation 6. D395 1 WARNING Blade Torque 7. D621 1 IMPORTANT Lube Spindle Every 40 hrs 8. D303 2 LOGO Rhino Logo 9. 00764866 2 LOGO Servis 2160 Nane 10. 1458392 1 REFLECT Yellow Reflector 11.
SAFETY Decal Description SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY SAFETY 2160 07/11 © 2011 Alamo Group Inc.
SAFETY Federal Laws and Regulations This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such. Employer-Employee Operator Regulations U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA Title 29, Code of Federal Regulations Part 1928.57(a)(6). www.osha.
Contents Acknowledgment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Alerts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 A Word To The User/Operator . . . . . . . . . . . . . . . . . . . . 3 The Industrial/Agricultural Mower. . . . . . . . . . . . . . . . . 4 Follow A Safety Program . . . . . . . . . . . . . . . . . . . . . . . . 5 Prepare For Safe Operation . . . . . . . .
Safety Alerts Symbol Signal Words This Safety Alert Symbol means: “ATTENTION! STAY ALERT! YOUR SAFETY IS INVOLVED!” Signal words are distinctive words that will typically be found on safety signs on the mower and other worksite equipment. These words may also be found in this manual and the manufacturer’s manuals. These words are intended to alert the operator to a hazard and the degree of severity of the hazard.
The Industrial/Agricultural Mower Industrial/Agricultural Mower Types Mowers are used for pasture clipping, crop residue shredding, heavy brush cutting, waterways, right-ofways, roadside or highway mowing. Also, these mowers are used for cutting grass and other growth in public areas such as parks and cemeteries. Flail Boom Rotary Sickle Bar Folding Wing Rotary The Industrial/Agricultural Mower Agricultural Disc Mower Types Disc mowers are designed and equipped to cut hay crops at higher field speed.
Follow A Safety Program Protect Yourself Wear personal protective clothing and Personal Protective Equipment (PPE) issued to you or called for by job conditions. You must ALWAYS wear safety glasses with side shields. You may also need: — Hard hat — Safety shoes — Safety goggles or face shield — Heavy gloves — Hearing protection — Reflective clothing — Wet weather gear — Respirator or filter mask Wear whatever is needed—don’t take chances.
Follow A Safety Program Avoid Injury From Raised Equipment Avoid Injury From High Pressure Fluid Avoid possible crushing injury from falling mower or other raised equipment. Avoid fluid injection injury due to high pressure fluid leaks. Avoid Crushing – Block Up or Securely Support Mower Before working near or under raised mower or equipment parts: — Securely support or block up raised mower or equipment parts according to the operator’s manual.
Follow A Safety Program Be Alert! For Safe Operation Know where to get assistance. Know how to use a first aid kit and fire extinguisher/fire suppression system. You must be a qualified and authorized operator for proper operation of your machine. You must clearly understand the written instructions supplied by the manufacturer, be trained—including actual operation of the mower—and know the safety rules and regulations for the worksite.
Follow A Safety Program Some Rules You Must Work By (continued) Keep Children Away from Equipment — Only qualified and authorized individuals may operate this equipment. — Never allow children to play on, ride on or operate the equipment. Children are not qualified to operate this equipment. — Do not allow any riders. — Use three-point contact (handholds and steps) and face the equipment when mounting or dismounting. — Keep bystanders 300 ft (92 m) from the mowing operation.
Prepare For Safe Operation Check The Mower And Tractor Equipment Before beginning your work day inspect the machine and have all systems in good operational condition. Walk-Around Inspection WARNING! Prevent possible crushing injury from falling equipment. Hydraulic system or part failure could cause unsupported equipment to fall. Do not go under raised equipment unless it is properly supported according to the operator’s manual.
Prepare For Safe Operation Know The Work Area Before you operate the mower thoroughly inspect the work area. Walk around the area and inspect the surfaces you will travel on when using the mower.
Prepare For Safe Operation Tractor And Mower Controls Safety Test Start the tractor following the specific procedures in the manufacturer’s operator’s manual. These procedures normally include: — Fasten and adjust seat belt on your ROPS-equipped tractor. — Check parking brake for engagement. — Check PTO disengagement. — Check all controls for Park position. — Warn others in area before starting tractor. — Start tractor following tractor manufacturer’s recommended starting procedures.
Prepare For Safe Operation Hitching Mower To Tractor Read and Understand Manuals Before Operating Three-point hitch-mounted mowers: — Refer to mower and tractor manufacturers’ manuals. — Place tractor’s hydraulic power lift (rockshaft) selector lever in down position to avoid unexpected movement. — Explain the hitching procedures to those operators who cannot read. — Front-end weights may be needed to maintain steering control and front-end stability. Refer to the manufacturers' operator's manual(s).
Start Safely Make The Right Start Mow only in daylight or good artificial light conditions. Avoid serious injury or death from mower-thrown objects or blade contact: — Keep chain shields, flexible or solid deflector shields or discharge chutes in place and in good repair. — Keep bystanders at least 300 ft (92 m) from mowing operation. — Never direct mower discharge toward anyone. — Keep hands, feet and other body parts away from rotating parts, blades and discharge openings.
Operate Safely Mower-Thrown Objects (continued) Disc Mowers — When using a disc mower it is important to know the area to be mowed. If the operator has mowed the field before and is familiar with all obstacles that may be present, it is sufficient to watch ahead of the mower path for any additional objects that may have entered the field. Be ready to stop or avoid any objects that could be hazardous if thrown by the mower.
Operate Safely Under Mount Mower Safety Practices When mowing with an under mount mower: — Keep removable discharge chute in place and over discharge opening. — Never stand on a mower housing when the tractor engine is operating. — Distribute grass clippings with discharge chute facing mowed area. — Before clearing a clogged mower or discharge chute, shut down your machine using proper equipment shut down practice. (See page 18, Proper Equipment Shut Down Practices.
Operate Safely Wing And Side Mount Mowers Safety Practices Raised wing positions reduce shielding protection and increases the thrown object and blade contact hazard risks. Avoid possible serious injury or death by thrown objects or blade contact from raising and lowering wings during mowing operations: — Do not mow with bystanders within 300 ft (92 m) of the mower. — Be sure no one is near mower while raising or lowering wings.
Operate Safely Uneven Terrain Mowing Safety Practices (continued) Maintain Control, Use Low Speeds — Use extreme care to maintain control over the equipment when operating in these conditions. — Increase tractor stability by adding wheel weights, ballast and increasing wheel spacing to maximum. Refer to operator’s manual for recommendations. — Maintain minimum ground speed. — Make wide and gradual turns. — Avoid sudden starts, stops, and turns when operating up, down, or across slopes.
Park Safely Parking Safety Practices — Use designated or out-of-traffic areas. — Use firm level ground locations. — Set parking brake. — Lower raised equipment to ground. P Shut down the mower and tractor using proper equipment shut down practice before dismounting tractor. (See page 18, Proper Equipment Shut Down Practices.) Set Parking Brake Lower Raised Equipment to Ground Sloping ground parking locations: — Position equipment across slope. — Set parking brakes. — Lower raised equipment to ground.
Shut Down Safely Dismounting Properly — Never dismount from moving equipment. — Never jump from any machines. — Dismount carefully. — Check for slippery steps. — Keep feet and hands away from controls. — Use handholds and steps during dismount. — Face machine and use three-point contact (2 hands and 1 foot or 2 feet and 1 hand).
Perform Maintenance Safely Prepare Yourself Wear personal protective clothing and Personal Protective Equipment (PPE) issued to you or called for by job conditions. You must ALWAYS wear safety glasses with side shields. You may also need: — Hard hat — Safety shoes — Safety glasses, goggles or face shield — Apron and gloves — Hearing protection — Welding helmet or goggles — Respirator or filter mask Wear whatever is needed—don’t take chances.
Perform Maintenance Safely Prepare The Machine Stored energy sources (electrical, mechanical, hydraulic, pneumatic, chemical, thermal, etc.) must be controlled or reduced to a practical minimum before performing any maintenance, repair or service procedures. Safety practices to prevent potential injuries from energy-releasing sources: — Disengage PTO before shutting off engine. — Place controls in PARK or NEUTRAL before shutting off engine. — Set parking brake or block wheels.
Perform Maintenance Safely Use Proper Ventilation If it is necessary to run an engine in an enclosed area, remove the exhaust fumes from the area with an exhaust pipe extension. If you do not have an exhaust pipe extension, make sure you open the doors and get outside air into the area. WARNING! Prevent possible injury. Never work on machinery with the engine running unless instructed by the manufacturer’s manuals for specific service.
Perform Maintenance Safely Hydraulic System Hazards The hydraulic system is under pressure whenever the engine is operating and may hold pressure even after the engine is shut off. Cycle all hydraulic controls including the auxiliary hydraulic control after the engine is shut down. Relieve trapped pressure in the lines after the attachments are shut down and resting on the ground. During inspection of the hydraulic system: — Wait for fluid to cool before disconnecting the lines.
Perform Maintenance Safely Avoid Explosion WARNING! Avoid possible serious injury from explosion. Lead-acid batteries produce extremely explosive gases especially when being charged. Keep arcs, sparks, flames and lighted tobacco away. — Do not smoke near batteries. — Keep arcs, sparks and open flames away from batteries. — Provide adequate ventilation. Never check the battery by placing a metal object across the battery posts — the resulting spark could cause an explosion.
Perform Maintenance Safely Tire And Wheel Maintenance (continued) WARNING! The types of wheels and tires usually found on this equipment require special care when servicing to prevent death or serious injury. Do not inflate the tires above the recommended pressure. Be sure to replace tire ballast if equipped. See manufacturer’s specifications for ballast requirements. Keep wheel lug nuts tightened to manufacturer’s recommendations. Never cut or weld on a wheel with an inflated tire mounted on it.
Perform Maintenance Safely Mower Blade Maintenance (continued) — How are mower blades made? Mower blades are made of high strength alloy spring steel. They are hot-forged and shaped to meet the manufacturer’s individual specifications, then heat treated and tempered to a high strength, ductile state to reduce the possibility of breaking while mowing. Blades are tested to ensure they meet strength, hardness, and ductility standards.
Contenido Reconocimiento . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Introducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Alertas de seguridad . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Palabras para el usuario/operador . . . . . . . . . . . . . . . . 3 Cortadora de césped industrial/para agricultura . . . . 4 Cumplimiento del programa de seguridad . . . . . . . . . 5 Preparación para una operación segura . . . . . . . . . . .
Alertas de seguridad Símbolo Palabras indicativas Este símbolo de alerta de seguridad significa: “¡ATENCIÓN! ¡MANTÉNGASE ALERTA! ¡SU SEGURIDAD ESTÁ EN RIESGO!” Las palabras indicativas son palabras distintivas que típicamente se encontrarán en letreros de seguridad de la cortadora de césped y otros equipos del sitio de trabajo. Estas palabras también se pueden encontrar en este manual y en los manuales del fabricante.
Cortadora de césped industrial/para agricultura Tipos de cortadora de césped industrial/para agricultura Las cortadoras de césped se usan para recortar pasturas, desmenuzar residuos de cultivos, cortar arbustos, realizar desbroce pesado, cortar la hierba en vías de agua, derechos de paso, costados de caminos o autopistas. Además, estas cortadoras se usan para cortar la hierba y otras plantas en zonas públicas como parques y cementerios.
Cumplimiento del programa de seguridad Protéjase a sí mismo Use la ropa de protección personal y los equipos de protección personal (PPE) que se le proporcionen o que requieran las condiciones del trabajo. SIEMPRE debe usar gafas de seguridad con escudos laterales.
Cumplimiento del programa de seguridad Evite las lesiones provocadas por equipos elevados Evite posibles lesiones de aplastamiento por caídas de la cortadora u otros equipos elevados. Evite ser aplastado – Bloquee o apoye con seguridad la cortadora Antes de trabajar cerca o debajo de partes levadas de la cortadora o de los equipos: — Apoye o bloquee con seguridad las partes elevadas de la cortadora o los equipos de acuerdo con el manual del operador.
Cumplimiento del programa de seguridad ¡Manténgase alerta! Para una operación segura Sepa dónde obtener asistencia. Sepa cómo usar un equipo de primeros auxilios y un extintor de incendios/ sistema de supresión de fuego. Usted debe ser un operador cualificado y autorizado para operar la máquina correctamente.
Cumplimiento del programa de seguridad Algunas reglas que debe cumplir al trabajar (continuación) — Únicamente personas cualificadas y autorizadas pueden manejar estos equipos. — Nunca permita que los niños jueguen en los equipos, viajen en ellos o los hagan funcionar. Los niños no están cualificados para manejar estos equipos. — No transporte pasajeros. — Use contacto en tres puntos (asideros y peldaños) y enfrente el equipo al ascender o descender de él.
Preparación para una operación segura Revise los equipos de la cortadora de césped y el tractor Antes de comenzar la jornada de trabajo, inspeccione la máquina y asegúrese de que todos los sistemas estén en buenas condiciones operacionales. ¡ADVERTENCIA! Evite posibles lesiones por aplastamiento producidas por equipos que caen. La falla del sistema hidráulico o de una parte podría causar la caída de equipos que no están apoyados.
Preparación para una operación segura Familiarícese con la zona de trabajo Antes de hacer funcionar la cortadora de césped, inspeccione cuidadosamente la zona de trabajo. Recorra a pie alrededor de la zona e inspeccione las superficies sobre las cuales se desplazará cuando utilice la cortadora.
Preparación para una operación segura Prueba de seguridad de los controles del tractor y de la cortadora de césped Arranque el tractor siguiendo los procedimientos específicos del manual del operador del fabricante. Estos procedimientos normalmente incluyen: — Colóquese y ajústese el cinturón de seguridad en el tractor equipado con ROPS. — Verifique que el freno de estacionamiento esté aplicado. — Verifique que la TDF esté desenganchada.
Preparación para una operación segura Enganche de la cortadora de césped al tractor Lea y asegúrese de comprender los manuales antes de comenzar la operación Cortadoras montadas en enganche de tres puntos: — Consulte los manuales de los fabricantes de la cortadora y del tractor. — Coloque la palanca selectora de elevación de potencia hidráulica del tractor en la posición descendida para evitar movimientos imprevistos. — Explique los procedimientos de enganche a los operadores que no puedan leerlos.
Arranque con seguridad Cómo realizar un arranque correcto Corte la hierba únicamente con luz diurna o en condiciones de buena luz artificial. Evite lesiones graves o muerte producidas por objetos arrojados por la cortadora o por el contacto con las hojas: — Mantenga los escudos de las cadenas, los escudos deflectores flexibles o sólidos y las rampas de descarga en su lugar y en buen estado de reparación. — Mantenga a las personas ajenas a 300 pies (92 m) de la operación de corte.
Operación con seguridad Objetos arrojados por la cortadora de césped (continuación) Apague la TDF, espere que las hojas dejen de girar, eleve la cortadora y, después, retroceda. Cortadoras de disco — Cuando se usa una cortadora de disco, es importante conocer la zona donde se va a cortar.
Operación con seguridad Prácticas de seguridad para la cortadora de césped de montaje inferior Cuando se traslada con una cortadora de césped de montaje inferior: — Mantenga la rampa de descarga extraíble en su lugar y por encima de la abertura de descarga. — Nunca se pare sobre la carcasa de una cortadora de césped cuando el motor del tractor está en funcionamiento. — Distribuya los recortes de hierba con la rampa de descarga orientada hacia la zona donde se cortó.
Operación con seguridad Prácticas de seguridad para cortadoras de césped con laterales y montaje lateral 300 ft (92 m) Las posiciones elevadas de los laterales reducen la protección de los escudos y aumentan los riesgos de objetos arrojados y contacto con las hojas.
Operación con seguridad Prácticas de seguridad para trabajos de corte en terrenos desparejos (continuación) — Use extremo cuidado para mantener el control de los equipos cuando trabaja en estas condiciones. — Aumente la estabilidad del tractor agregando pesos o lastre en las ruedas y aumentando al máximo la separación entre las ruedas. Consulte las recomendaciones en el manual del operador. — Mantenga la velocidad de desplazamiento en el mínimo. — Realice giros amplios y graduales.
Estacionamiento seguro Prácticas de seguridad para el estacionamiento — Use las zonas designadas o alejadas del tránsito. — Use lugares con suelo firme y nivelado. — Aplique el freno de estacionamiento. — Descienda el equipo de la cortadora de césped hasta el suelo. P Apague la cortadora y el tractor usando la práctica correcta de apagado de equipos antes de descender del tractor. (Consulte la página 18, Prácticas correctas de apagado de los equipos.
Apagado con seguridad Descenso correcto — Nunca descienda de equipos en movimiento. — Nunca baje de una máquina saltando. — Descienda con cuidado. — Verifique que no haya peldaños resbaladizos. — Mantenga los pies y las manos lejos de los controles. — Use los asideros y los peldaños durante el descenso. — Enfrente la máquina y use contacto de tres puntos (2 manos y 1 pie o 2 pies y 1 mano).
Realización de mantenimiento con seguridad Preparación personal Use la ropa de protección personal y los equipos de protección personal (PPE) que se le proporcionen o que requieran las condiciones del trabajo. SIEMPRE debe usar gafas de seguridad con escudos laterales.
Realización de mantenimiento con seguridad Preparación de la máquina Deben controlarse o reducirse las fuentes de energía almacenada (eléctricas, mecánicas, hidráulicas, neumáticas, químicas, térmicas, etc.) al mínimo practicable antes de realizar cualquier procedimiento de mantenimiento, reparación o servicio. Prácticas de seguridad para prevenir posibles lesiones por fuentes que liberan energía: — Desenganche la TDF antes de apagar el motor.
Realización de mantenimiento con seguridad Use ventilación adecuada Si es necesario hacer funcionar un motor en una zona cerrada, elimine del área las emanaciones de escape con una extensión del caño de escape. Si no tiene esa extensión, asegúrese de abrir las puertas y dejar entrar aire del exterior. ¡ADVERTENCIA! Evite posibles lesiones. Nunca trabaje en la maquinaria con el motor en funcionamiento salvo que así lo indiquen los manuales del fabricante para un servicio en particular.
Realización de mantenimiento con seguridad Riesgos del sistema hidráulico El sistema hidráulico se encuentra bajo presión siempre que el motor está funcionando; puede conservar presión incluso después de apagar el motor. Haga funcionar todos los controles hidráulicos incluyendo el control hidráulico auxiliar después de que el motor esté apagado. Alivie la presión atrapada en las líneas después de que los accesorios están apagados y apoyados en el suelo.
Realización de mantenimiento con seguridad Evite explosiones ¡ADVERTENCIA! Evite posibles lesiones graves por explosiones. Las baterías de plomo-ácido producen gases sumamente explosivos, especialmente durante la carga. Mantenga alejados los arcos, las chispas, las llamas y el tabaco encendido. — No fume cerca de las baterías. — Mantenga los arcos, las chispas y llamas abiertas alejadas de las baterías. — Proporcione ventilación adecuada.
Realización de mantenimiento con seguridad Mantenimiento de neumáticos y ruedas (continuación) ¡ADVERTENCIA! Los tipos de ruedas y neumáticos que generalmente se encuentran en estos equipos requieren cuidados especiales al realizar servicios para evitar lesiones graves o la muerte. No infle los neumáticos por encima de la presión recomendada. Asegúrese de volver a colocar el lastre de los neumáticos si está instalado. Consulte las especificaciones del fabricante para ver los requisitos de lastre.
Realización de mantenimiento con seguridad Mantenimiento de las hojas de la cortadora (continuación) — ¿Cómo están hechas las hojas de la cortadora de césped? Están hechas acero para resortes de aleación de alta resistencia. Se forjan en caliente y se les da forma para cumplir con las especificaciones individuales del fabricante; luego, se tratan y templan a un estado dúctil, de alta resistencia para reducir la posibilidad de rupturas durante el corte.
INTRODUCTION SECTION Introduction Section 2-1 © 2011 Alamo Group Inc.
INTRODUCTION INTRODUCTION This Boom Mower is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine. The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in the correct assembly of the Mower using standard and optional equipment.
INTRODUCTION INTRODUCTION The 2160 is ideal for mowing pond embankment, levees or drainage ditches, and cutting overhanging limbs on fence rows. Features 158” Reach from Center of Tractor Hydraulic Driven 60 Gallon Oil Reservoir Doubles as Counterweight 85 Degree Vertical Head Movement and 90Degree Downward Optional Gauge Wheels for Better Ground Contour Movement Warranty - One year parts and labor. Non-governmental users subject to a modified policy.
INTRODUCTION ATTENTION OWNER/OPERATOR BEFORE OPERATING THIS MACHINE: 1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and know how to operate correctly both the tractor and Mower. INTRODUCTION 2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the Mower. Mail within 30 days of delivery date of this implement.
INTRODUCTION RHINO LIMITED WARRANTY (a)Repair or replace the defective goods or part(s) or (b)Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer) if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty by Manufacturer. The choice of remedy shall belong to Manufacturer. 2.05.
ASSEMBLY SECTION Assembly Section 3-1 © 2011 Alamo Group Inc.
ASSEMBLY General Assembly To help you assemble your New 2160 and mount it to your tractor, we provide you with drawings, instructions and general information. When needed, you can get information or clarification from Rhino Customer Service. This publication provides general information not specifically for your case or tractor, but, in connection with the drawings. This publication offers you some valuable assistance - please read it thoroughly.
ASSEMBLY TRACTOR PREPARATION 1. Move left rear tire out so that it is 50 inches minimum from the outside of left rear tire to the center of tractor. Then move the right rear tire out so that it is 96 inches minimum between the outside of the left and right rear tires. Refer to your tractor’s Operator’s Manual for instructions on Rear Wheel Adjustment for your particular tire. Asm-B-0029. Install fluid ballast inn left rear tire as needed for stability.
ASSEMBLY MOWER TO TRACTOR ATTACHMENT ASSEMBLY This mower is designed for 540 or 1000 RPM PTO with CAT II or CAT III Quick Hitch (Standard) or CAT II or CAT III 3-Point Hitch (Optional). CAT II and III Quick Hitch ( Standard) (Asm-B-0031) Back-up tractor with Quick Hitch and align bottom lugs (1) of hitch to lower lugs (2) of frame. Then raise lift arms until Pins (3) lock into lower lugs (1). Top lug (4) on Quick Hitch should simultaneously hitch to Pin (5) on top of Rhino Boom Frame.
ASSEMBLY DRIVELINE LENGTH CHECK PROCEDURE Before using mower check driveline length with tractor attached to mower. 1. Separate two halves of driveline and connect one half to tractor and the other half to mower. 2. Lower mower to normal operating position. 3. Bring the two driveline halves together as shown in figure 6. At this maximum compressed length there should be 1-1/2 inches or more clearance from tubes bottoming out. If not, shorten the driveline to obtain clearance.
ASSEMBLY ATTACHMENT OF HYDRAULIC HOSES Once pumps are installed, DO NOT start the tractor (which will turn the pumps) unless thehydraulic circuits are completed and filled with the specified universal tractor hydraulic oil. Running pumps without oil will cause non-warrantable damage. ASSEMBLY It is important that pipe thread sealant be used only on pipe threads; never on connections or on straight thread "O" ring fittings. Use the pipe thread sealant supplied.
ASSEMBLY ATTACHMENT OF HYDRAULIC HOSES It is important that pipe thread sealant be used only on pipe threads; never on 37 degree flared fitting or on straight thread “O” ring fittings. Use the pipe thread sealant supplied. Do not substitute with some other type of sealant, such as, teflon tape, paint, shellac, etc.
ASSEMBLY ASSEMBLY HOSES TO VALVE CONNECTIONS FOR ELECTRONIC CONTROL (OPTIONAL) Refer to Asm-B-0032 & Asm-B-0030 and parts section page 6-24 for proper hose routing. Attach the electric valve to the plate using the two 3/8 x 5 bolts, four 3/8 flatwashers, and two 3/8 lockwashers. Connect the valve to open auxiliary hydraulic ports of the tractor. By connecting supply hoses to the valve "P1" and "P2". Both valve hoses will be p/n 02961036. Use recommended torque values. a.
ASSEMBLY MOUNTING THE REMOTE COMMAND HANDLE After mounting the handle, route the cable away from the handle leaving enough slack in the line to provide free movement of the control. Secure the cable with the cable ties included. Unless otherwise specified, all control systems are designed for use on 12 volt, negative ground electrical systems only. The red and black power wires are to be connected as follows: Connect the black wire to the frame of the vehicle or to the grounded terminal of the battery.
ASSEMBLY ASSEMBLY HOSE CONNECTIONS (DIRECT) (Asm-B-0032) This hydraulic connection methods requires a break-away valve for the swing cylinder. This valve will be mounted to the top of a valve mount plate on the Main frame (7) with 2 - 1/4" x 2 3/4" bolts (1) and fasten with 1/4" locknuts (2).Hoses from the tractor ports are then connected to the straight adapters (3). Hoses from the swing cylinder are connected to the 90 degree elbows (4).
ASSEMBLY HEAD ATTACHMENT 1. Align the boom arm with the mower head lugs. Then insert main pin (1) and lock down with a 3/8 x 2 1/2 bolt (2) and a 3/8 nut. Attach linkage with 2 - 3/4 x 3 bolts (3) and lock with 2 -3/4 nuts (4). ASSEMBLY HOSE ATTACHMENT 1. Attach the 1 " hoses, from the articulating arm to the hydraulic motor on the head. Use recommended hose end torque values in chart on Section 3-5. 2160 07/11 © 2011 Alamo Group Inc.
ASSEMBLY HYDRAULIC RELIEF ATTACHMENT (OPTIONAL) (Asm-B-0037) (Required if attaching to a Non-Quick Hitch Tractor) 1. Remove the top link of the three point from the tractor. 2. Connect the center lug (1) of the Hydraulic Relief Arm (HRA) to the tractor, with the double lugs (2) up, where the top link was removed. ASSEMBLY 3. Back the tractor up to the SERVIS 2160 and connect the lower arms (3) of the three point, making sure that the HRA does not interfere with the SERVIS 2160. 4.
ASSEMBLY STARTING UNIT 1. Make sure unit has been properly assembled, all cylinders, Hoses, and the driveline have been connected. NOTE: Make sure that no materials, tools, or jacks have been left under the mower head. Make sure the front and rear of the mower are properly guarded to prevent any foreign objects from being thrown by the mower. All other workers should keep a safe distance from the unit before the mower is started. 2.
ASSEMBLY ASSEMBLY 7. When adding hydraulic oil, use only new oil from a sealed barrel. Used oil or oil from an open barrel may contain high levels of contamination. Transfer the oil into the hydraulic tank by using a hydraulic filter pump unit equipped with a properly operating 10 micron filter. This will insure that the oil being added is clean.
ASSEMBLY ASSEMBLY All Servis and Servis-Rhino Boom Mowers mounted on Non-Cab Tractors require without exception a suitable Operator Protective Cage be installed before operating to prevent Operator injury by objects thrown by the blades. The Servis Operator Protective Cage may be ordered with the machine or from the Extra Equipment Section (For your particular tractor, some modification to this Cage may be necessary.
OPERATION SECTION Operation Section 4-1 © 2011 Alamo Group Inc.
OPERATION RHINO 2160 BOOM MOWER OPERATING INSTRUCTIONS OPERATION Rhino Booms are manufactured with quality material by skilled workers. The 2160 is designed to attach to a tractor and mow pond banks,levees, drainage ditches, roadsides or other agricultural applications that may apply. The boom and head is equipped with safety warning decals, protective deflectors, shields, and other safety features to provide operator and passerby protection, however, no shielding is 100% accurate.
OPERATION 1.Standard Equipment and Specifications HYDRAULIC BOOM ROTARY CUTTER 60” 1-3/4” 2” 100 HP CAT II-III Q.H. 69” 71-3/8” 113” CAT 4 55 Gallons 20,028 FPM Clockwise Pan 21’ 22’, 6” 11’, 6” 3000 PSI Standard 2750 PSI 190 degrees 10 Ga. 1/4” x 9-1/4” Standard Standard 2700 lbs. with Oil EXTRA EQUIPMENT OPTIONAL EQUIPMENT Hydraulic Relief Arm Kit (For Non-Quick Hitch Tractor) 540 or 1000 RPM Electro-Hydraulic Cylinder Control Valve Kit Hyd. Valve Kit for Direct Connect (Tractors with 4-Spool Hyd.
OPERATION 2.OPERATOR REQUIREMENTS OPERATION Safe operation of the unit is the responsibility of a qualified operator. A qualified operator has read and understands the implement and tractor Operator’s Manuals and is experienced in implement and tractor operation and all associated safety practices. In addition to the safety messages contained in this manual, safety signs are affixed to the implement and tractor.
OPERATION 3.TRACTOR REQUIREMENTS In addition to tractor horsepower and size required to operate the boom unit, the tractor must also be properly equipped to provide operator protection, to alert approaching vehicle drivers of the tractor’s presence, and to ensure tractor stability when mowing with the boom fully extended. Tractor Requirements and Capabilities Certified Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt. Tractor Safety Devices .....................
OPERATION OPERATION 3.4 Tractor Ballast To ensure tractor stability when operating on flat surfaces the left rear tractor tire MUST exert a minimum down force (weight) of 1500 lbs. on the ground when the tractor is on level ground, its boom is fully extended and the mower head is horizontal and two feet above the ground.
OPERATION 3.6 Power Take Off (PTO) Depending on the unit, the mower is designed to operate at a PTO speed of 540 or 1000 RPM. Most tractors operate at either 540, or a combination of 540 and 1000 RPM PTO speeds. The operating speed of the mower and tractor can be determined by the number of splines on the driveline yoke and PTO output shaft. Those operating at 540 RPM will have a 6-spline shaft and those operating at 1000 RPM will have a 21-spline shaft or a 1-3/4” 20 spline shaft.
OPERATION 4.GETTING ON AND OFF THE TRACTOR Before getting onto the tractor, the operator must read and completely understand the implement and tractor operator manuals. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. OPS-U- 0007 OPERATION Do not mount or dismount the Tractor while the tractor is moving. Mount the Tractor only when the Tractor and all moving parts are completely stopped. (SG-12) 4.
OPERATION 4.2 Dismounting the Tractor Before dismounting the tractor, idle the tractor engine down, disengage the head and retract the boom arm to the transport position. Park the tractor on a level surface, place the transmission in neutral and set the parking brake. Shut down the tractor engine, remove the key, and wait for all motion to come to a complete stop before exiting the operator’s seat. NEVER leave the seat until the tractor, its engine, and mower head movement have come to a complete stop.
OPERATION Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health. (SG-23) OPERATION Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operators manual for proper starting instructions. (SG-13) 6.CONNECTING ATTACHING HEADS TO THE BOOM 1. Start by using a hoist to lower the boom down to the head.
OPERATION Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order. (SG-21) 7.
OPERATION 7.2 Boom Unit Pre-Operation Inspection and Service Inspect and service the boom arm and head prior to operation. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure the unit is ready for operation, conduct the following: OPERATION OPS-B- 0020 Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings.
OPERATION BOOM ARM ASSEMBLY • • • • • Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. (SG-20) Never Leave the mower unattended while the head is in the raised position. The mower could fall causing serious injury to anyone who might inadvertently be under the mower. (SBM-4) HYDRAULIC LINE INSPECTION • • • • Check for hydraulic leaks along hoses, cylinders and fittings.
OPERATION OPERATION Do not operate this Equipment with hydraulic oil or fuel leaking. Oil and fuel are explosive and their presence could present a hazard. Do not check for leaks with your hand! High-pressure oil streams from breaks in the line could penetrate the skin and cause tissue damage including gangrene. To check for a hose leak, SHUT the unit ENGINE OFF and remove all hydraulic pressure. Wear oil impenetrable gloves, safety glasses and use Cardboard to check for evidence of oil leaks.
OPERATION HYDRAULIC PUMP/OIL RESERVOIR • • • Check the fluid level in the Hydraulic Tank on the Tractor, and add oil if required. As the air has been forced out of the Cylinders and Hoses, it goes into the Hydraulic Tank and reduces the volume of oil. Maintain the oil level within the sight gauge located on the side of the resevoir. Never fill the tank above the sight gauge to allow for the expansion of the oil. The tank maintains pressure after the mower has been run.
OPERATION ROTARY HEAD INSPECTION • • OPERATION • • • Inspect blades and blade bolts for looseness and excessive wear. Rotate to 90° to make for checking easier. Replace damaged, worn, and missing blades as complete sets to maintain rotary balance. Ensure carrier hub nuts are tightened with the cotter pin inserted and spread. Ensure rubber deflectors are in position and not damaged. Replace worn, broken, and missing sections immediately.
OPERATION 7.3 Cutting Component Inspection Inspect blade pan and blade assembly for the following: OPERATION OPS-U-0031 2160 06/11 © 2011 Alamo Group Inc.
OPERATION Inspect the Blades daily for abnormal wear. REPLACE BOTH BLADES on that carrier IMMEDIATELY if either blade has: OPERATION • • • • • Become bent or deformed from it’s original shape or Any cracks are visible, or Deep gouges in the blade’s surface are present, or Gouges or chipped areas in the cutting edge are larger than 1/2”(12.7mm), or The material on the leading edge has been worn away by more than 1/2(12.
OPERATION 7.4 Blade Bolt Inspection Inspect Blade Bolt Head daily for wear as followed: OPERATION Inspect the Blade Bolt Heads daily for abnormal wear. REPLACE BOTH BLADE BOLTS on the Blades IMMEDIATELY if either blade bolts has: • Visible cracks or • If the recessed area on blade bolt is worn off or • If Blade Bolt has gouges or chipped areas.
OPERATION OPERATION Tractor PRE-OPERATION Inspection Tractor ID#________________ Make ____________________ Date: Shift ________________ ____________________ Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the mower is resting on the ground or securely blocked up and all hydraulic pressure has been relieved. Condition at Start of Shift Item Specific Comments if not O.K.
OPERATION Boom Mower PRE-OPERATION Inspection Mower ID#________________ Make ____________________ Date: Shift ________________ ____________________ Condition at Start of Shift Item Specific Comments if not O.K.
OPERATION 8.DRIVING THE TRACTOR AND IMPLEMENT OPERATION Safe tractor transport requires the operator to possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement. Ensure the tractor has the capacity to handle the weight of the boom and the tractor operating controls are set for safe transport. To ensure safety while driving the tractor with a boom, review the following. Read all safety instructions.
OPERATION Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly. Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment.
OPERATION 8.2 Brake and Differential Lock Setting OPERATION Make sure the tractor brakes are in good operating condition. Tractor brakes can be set to operate independently allowing single rear wheel braking action or locked together to provide simultaneous rear wheel braking. FOR MOST DRIVING AND OPERATING CONDITIONS, THE BRAKE PEDALS SHOULD BE LOCKED TOGETHER TO PROVIDE THE MOST EFFECTIVE BRAKING ACTION. Always disengage the tractor differential lock when turning.
OPERATION 8.3 Driving the Tractor and Boom Inspect the area to be mowed before beginning operation. Identify any drop-offs, slopes, holes, hidden obstructions or similar obstacle that could cause the tractor to loose stability and potential roll-over. Mark and avoid the item or the entire area. Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the tractor.
OPERATION 9. OPERATING THE TRACTOR AND IMPLEMENT OPERATION THE OPERATOR MUST COMPLETELY UNDERSTAND HOW TO OPERATE THE TRACTOR AND IMPLEMENT AND ALL CONTROLS BEFORE ATTEMPTING TO OPERATE. The operator must read and understand the Safety and Operation Sections of the implement and tractor operator’s manuals. These manuals must be read and explained to any operator who cannot read. Never allow someone to operate the implement and tractor without complete operating instructions.
OPERATION OPERATION The mower valve comes with a push-pull operator switch that, when properly installed, will prevent the tractor from starting if the switch is in the ON position (pulled out). To properly install the push-pull operator, follow the wiring diagram shown. Failure to properly install this switch could result in injury to the operator or bystander. Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat with the seat belt securely fastened around you.
OPERATION The valves and their use will be explained in the following pages of this manual. Read each explanation carefully then practice in a safe, level area, CLEAR of all people, animals, and any obstructions. As always, use extreme caution when using this machine. This valve is controlled by operating the Remote Control Valve Box mounted to the right of the operator at a convenient height. NOTE: The stamped metal plate located above the control valve indicates each valve function.
OPERATION 9.2 Foreign Debris Hazards/Overhead Obstructions An area to be cut must first be inspected for objects that could be thrown or that could damage the machine. Walk through the area looking for fences, boulders, rocks, culverts, stumps or metal objects. Mark the inspected area with flags. If the area is dense and cannot be walked thoroughly it may be necessary to inspect a smaller area as well as possible, then trim away the part that has been inspected and can safely be removed.
OPERATION Rotary Mowers are capable under adverse conditions of throwing objects for great distances 300 feet or more) and causing serious injury or death. Follow safety messages carefully.
OPERATION There are obvious and hidden potential hazards in the operation of this Mower. REMEMBER! This machine is often operated in heavy brush and in heavy weeds. The Blades of this Mower can throw objects if shields are not properly installed and maintained. Serious injury or even death may occur unless care is taken to insure the safety of the operator, bystanders, or passersby in the area. Do not operate this machine with anyone in the immediate area. Stop mowing if anyone is within 300 feet of mower.
OPERATION OPERATION There are obvious and hidden potential hazards in the operation of this Mower. REMEMBER! This machine is often operated in heavy brush and in heavy weeds. The Blades of this Mower can throw objects if shields are not properly installed and maintained. Serious injury or even death may occur unless care is taken to insure the safety of the operator, bystanders, or passersby in the area. Do not operate this machine with anyone in the immediate area.
OPERATION 9.5 Operational Instruction The rotating parts of this machine have been designed and tested for rugged use. However, the blades could fail upon impact with heavy, solid objects such as metal guard rails and concrete structures. Such impact could cause the broken objects to be thrown outward at very high velocities. To reduce the possibility of property damage, serious injury, or even death, never allow the cutting blades to contact such obstacles.
OPERATION 9.6 Shutting Down the Attached Head OPERATION To shut down attached boom head, first bring the tractor to a complete stop. Keep the engine speed at normal operating speed of 540 RPM, and push the Motor Switch IN to the Stop position. The mower head will come to a complete stop with in 15 seconds.
OPERATION DETACHING AND STORING 1. 2. 3. 4. 5. 6. Quick - Hitch Swing the mower head to the rear. Place mower head on the ground. Make sure dipper section is vertical. Disconnect PTO. Level the frame by adjusting the boom. Lower the stands onto the ground. 7. Disengage the locking mechanism on the quick hitch. 8. Lower the 3-point hitch arms until quick hitch comes off the frame. 10.1 Hydraulic Relief Arm 1. 2. 3. 4. 5. 6. 7. 8. Swing the mower head to the rear. Place the mower head on the ground.
OPERATION Never allow children to play on or around Tractor or Implement. Children can slip or fall off the Equipment and be injured or killed. Inadvertent contact with controls can cause the Implement to shift or fall crushing themselves or others. (SG-25) OPERATION 11.TRANSPORTING THE TRACTOR AND IMPLEMENT Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind when you finish working in an area.
OPERATION Before transporting tractor between locations, idle the tractor engine, disengage the attached head, and wait for all head motion to come to a complete stop. Place the boom in its storage cradle rest support and then turn the joystick master switch to the OFF position. Placing Boom Articulating Arm on Boom Arm Rest • Before transporting the tractor on a public roadway or boarding a trailer for transport, the tractor brake pedals should be locked together.
OPERATION 11.1 Transporting on Public Roadways OPERATION Extreme caution should be used when transporting the tractor and mower on public roadways. The tractor must be equipped with all required safety warning features including a SMV emblem and flashing warning lights to alert drivers of the tractor’s presence. Remember that roadways are primarily designed for automotive drivers and most drivers will not be looking out for you, therefore, you must look out for them.
OPERATION When operating on public roads, have consideration for other road users. Pull to the side of the road occasionally to allow all following traffic to pass. Do not exceed the legal speed limit set in your country for agricultural tractors. Always stay alert when transporting the tractor and implement on public roads. Use caution and reduce speed if other vehicles or pedestrians are in the area. OPSU- 0022 Reduce speed before turning or applying the brakes.
OPERATION 11.2 Hauling the Tractor and Implement OPERATION Before transporting a loaded tractor and implement, measure the height and width dimensions and gross weight of the complete loaded unit. Ensure that the load will be in compliance with the legal limits set for the areas that will be traveled through. OPS-U- 0024_TK Use adequately sized and rated trailers and equipment to transport the tractor and implement. Consult an authorized dealer to determine the proper equipment required.
OPERATION Arrange the chains so that when tightened, the chains are pulling downward and against themselves. Carefully tighten the securing chains or other fasteners using boomers or binders to apply maximum tension. Use extreme care when attaching and removing the securing devices as the extreme tension involved when released has the potential to inflict serious injury. NOTE: Always transport per you state law regulations for tie down requirements. OPS-U- 0026_TK 2160 06/11 © 2011 Alamo Group Inc.
OPERATION 12.
OPERATION Problem Cylinder Excessive Drift Possible Cause May be normal Operation Cylinder Piston Seals Bypass Damaged or Defective Work Port Relief Valves Main Valve Spool Leakage Cylinder Leaks at Fittings Cylinder Leaks at Rod Cylinder Moves Wrong Way (Not the function that was actuated) Related to Issues described in Previous section: Boom moves under its own power Loose Fittings Wrong Fittings Installed Damaged or defective fitting (cracked) Fitting Port cracked Faulty Seals on Cylinder Gland Da
OPERATION Problem OPERATION Cylinder Moves Spongy or Jerky Possible Cause Air in oil Check Specifications for proper oil, and replace Oil is cold System must be warmed to at least 40degrees F for proper operation. Check or test then replace or repair as required.
OPERATION Problem Cylinder Rod Came Out of Cylinder Deck Cracks Hydraulic System Noise (Squeal) Hydraulic System Overheating Vibration Poor or missing welds Mowing over sand or rocks Blades or blade bar bent, or blade missing Manufacturing defect Operator abuse Abusive operation, mowing heavy debris Normal operational wear Operator abuse Restrictions to oil flow in the system Relief Valve Malfunction Identified by concentration of heat, due to Line restriction bent hoses or contamination.
OPERATION Problem OPERATION Motor Inoperative (Won't Run) Motor Overheating Possible Cause Remedy Improper Oil Used Solenoid valve Failure or O-ring Failure at the Solenoid Valve No voltage to Solenoid Valve Incorrect Wiring at Solenoid valve flush and replace the oil Remove the solenoid valve and inspect. Replace as required Spindle Locked up Check by spinning blades. See Section on spindle failures Fill or replace as required Flush and fill as required Locate the source and repair.
OPERATION Problem Motor Runs Too Slow (or Slows Down Under Load) Motor Stops (Stops under Load) Possible Cause Remedy Pump Drive Damaged Logic Valve O-ring Failure (Gear Systems) Damaged O-ring on Solenoid Valve Pump Worn or Defective Motor Damaged or defective Check drive shaft attachment to the tractor Remove logic valves and inspect seals. Replace as required Remove solenoid valve. Replace seals as required.
OPERATION Problem OPERATION Spindle Leaking At Motor Spindle Leaking Around Bottom Seal Spindle Leaking At Relief Vent Spindle Overheating Spindle Shaft Loose or Falls Out 2160 06/11 © 2011 Alamo Group Inc.
OPERATION Possible Cause Remedy Spindle Locks Up (Seizes and Won't Turn) Loss of lubrication in spindle Excessive bearing preload Indicated by catastrophic failure of the upper bearing. See the previous section Disassemble the spindle and inspect the bearings for wear. Re-assemble following the bearing pre-load specifications in the Technical Service Manual.
MAINTENANCE SECTION Maintenance Section 5-1 ©2011 Alamo Group Inc.
MAINTENANCE MAINTENANCE HAZARDS WITH MAINTENANCE OF IMPLEMENT AVOID SERIOUS INJURY OR DEATH FROM COMPONENT FAILURE BY KEEPING IMPLEMENT IN GOOD OPERATING CONDITION IN PERFORMING PROPER SERVICE, REPAIRS AND MAINTENANCE. BEFORE PERFORMING SERVICE, REPAIRS AND MAINTENANCE ON THE IMPLEMENT: • STOP ENGINE AND PTO, engage parking brake, lower implement, allow all moving parts to stop and remove key before • • • • • • • • • • • • • • • • dismounting from tractor.
MAINTENANCE PARTS INFORMATION PARTS INFORMATION Rhino mowers use balanced and matched system components for blade carriers, blades, cuttershafts, knives, knife hangers, rollers, drivetrain components, and bearings. These parts are made and tested to Rhino specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce mower performance, void warranties, and present a safety hazard. Use genuine Rhino mower parts for economy and safety.
MAINTENANCE MAINTENANCE 2160 06/11 ©2011 Alamo Group Inc.
MAINTENANCE HYDRAULIC FLUID There are two types of hydraulic oil used by the factory, reference the chart below, Mobil DTE 16m and Chevron 1000 THF. Also, note the ISO cleanliness requirement for your mower. Product 2160 Oil Type UTF Oil Specification ISO Cleanliness Filter Change Recommendation Oil Change Recommendation Chevron 1000 THF 18/16/14 First 100 / every 500 or 12 months First 500 / every 1000 or 12 months The above are prescribed intervals, but frequency may change based on use.
MAINTENANCE MAINTENANCE Proper Oil Level Maintain the oil level within the sight gauge located on the reservoir. When oil is cold, the level should be three-quarters up the sight gauge. Never fill the tank above that sight gauge level. A space is maintained above the sight gauge to allow for the expansion of the oil. Oil is added through the filler tube, if your tank does not have a filler tube then fill through the return filter located on the tank.
MAINTENANCE MAIN DRIVELINE & CAT 4 SAFETY SHIELD To remove the main inner driveline shield. Remove the locking screws. Align the bearing tabs with the cone pockets. Mnt-B-0043. Remove the half-guard and remove the bearing ring. Mnt-B-0044. MAINTENANCE Inspect the driveline shield for worn areas or cracks. If the shield has any dents or cracks, replace the Shield. While the Shields are off, examine the Driveline for signs of abnormal wear, bent or twisted shafts, or cracks in the shafts or tubes.
MAINTENANCE MAINTENANCE Make certain that the Driveline Integral Shields are free to telescope and rotate around the Driveline without binding. 2160 06/11 ©2011 Alamo Group Inc.
MAINTENANCE Blades Check the Blades for cracks and wear and Blade Bolts for tightness, daily. Blades should be replaced when they are worn excessively, bent, deformed, or out of balance. Blades should always be replaced in pairs. Blades of different weights can cause serious imbalance and damage to the machine and personnel. When replacing blades, take care to replace the blade bolts, nuts, and washers.
MAINTENANCE BLADE SERVICING Inspect blades before each use to determine that they are properly installed and in good condition. Replace any blade that is bent, excessively nicked, worn, or has any other damage. Small nicks can be ground out when sharpening. MAINTENANCE When sharpening blades, grind each blade the same amount to maintain balance. The difference in blade weights should not exceed 1 ounce. Unbalanced blades will cause excessive vibration which can damage gear box bearings.
MAINTENANCE BLADE SHARPENING Always sharpen both blades at same time to maintain balance. Follow original sharpening pattern as shown in FIGURE Mnt-R-0008. Always sharpen blades by grinding. DO NOT heat and pound out edge. Do not sharpen blade to a razor edge, but leave a 1/16" blunt edge. Do not sharpen back side of blade. Avoid personal injury. Always block the cutter up to prevent if from falling when the blades and/or carrier are being serviced.
MAINTENANCE BLADE CARRIER REMOVAL Remove cotter pin and loosen slotted nut on spindle shaft. Loosen but do not remove the nut until the blade carrier is loosened. Use long bar inserted through blade bolt access hole with the end against rotor bar. Strike opposite end of bar with sledge hammer. Rotate blade carrier 180 degrees and repeat process. MAINTENANCE BLADE CARRIER INSPECTION Blade bolt fit into carrier bushings should be checked every time blades are changed.
MAINTENANCE BLADE CARRIER INSTALLATION Clean the taper on both the blade carrier and output shaft. Position carrier on the gearbox output shaft and install special washer nut. Tighten nut, while holding blade carrier, to minimum 450 ft./lbs. strike the carrier near the hub several times with a heavy hammer to seat the hub. Use a suitable spacer over the nut to prevent damage to the nut and threads. Retighten the nut to 450 ft./lbs. Install cotter pin and spread.
MAINTENANCE Hardware Most nuts and bolts will stay tight and therefore need only periodic checking. However, the following nuts and bolts are extremely important and should receive special attention: Spindle Housing Bolts: Tighten to 400 Ft./Lbs. Torque Blade Bolts: Tighten to 400 Ft./Lbs. Torque MAINTENANCE Blade Bar To Spindle Bolts: Tighten to 400 Ft./Lbs.
MAINTENANCE Boom Cylinder Removal and Replacement Instructions 1. 2. 3. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 2160 06/11 ©2011 Alamo Group Inc. Maintenance Section 5-15 MAINTENANCE 4. 5. 6. Clear the area of all personnel before lowering the boom mower head. From the tractor seat with your seat belt fastened around you, Lower the boom mower head to the ground. Extend the boom to the furthest reach and lower the mower head flat on the ground.
MAINTENANCE MAINTENANCE Hydraulic Component Maintenance Schedule Component Installation X Pump Drive Shaft Check and Lubricate Pump Mounting Bolt torque check (Inspect Daily) X Installation Charge Pump Filter Installation Pressure Filter to the Control Valve Installation Return Canister Filter Element Installation Hydraulic Oil Change Hydraulic Oil Particle Count Testing X Installation Hydraulic Tank Breather Filter Installation Hydraulic Tank Suction Screen Installation Hydraulic Hose Inspection/Replace
MAINTENANCE Cleaning Procedure for Large Areas - Automated 1. 2. Clean the surface using a high-pressure water cleaner (max. 10Obar or 1,450psi) and/or a steam cleaner. We suggest that a test be made on a small area, prior to cleaning the entire sheet Use of additives to the water and/or steam should be avoided. Other Important Instructions for All Lexan Sheets: • • • • • • Never use abrasive or highly alkaline cleaner on Lexan polycarbonate materials.
MAINTENANCE MAINTENANCE 2160 06/11 ©2011 Alamo Group Inc.
MAINTENANCE SERVICE OF SPINDLE HOUSING (FIGURE Mnt-0006) Remove blade bar or pan. Remove hydraulic motor. Remove spindle housing from unit. Using a chisel, bend the tang on the lockwasher (6) until it is free from the slot in the nut (5). Unscrew locknut and remove lockwasher, and second locknut. locknut and The Spindle should now slide from the Spindle housing, so the Spindle can be removed from the Housing.
MAINTENANCE Assembly Make sure all parts are clean and free of any contamination Install Bearing Cups (3 & 4) into Spindle Housing (2) using a suitable bearing driver to seat the cups. Caution must be taken not to damage the cup or spindle housing, cups must be fully seated.
MAINTENANCE MOTOR & COUPLING INSTALLATION Insert motor shaft into flex coupling and allow motor to “find its center”. Adjust motor up as needed to provide ample clearance between the top of flex coupling and the motor. Bring angle brackets up to motor mount plate and tighten the bolts. TAPER BUSHING & SHEAVE INSTALLATION Do not use lubricants during installation as this may cause sheave breakage. Make sure the bushing and bore of the sheave are free of dirt, paint, metal chips, etc.
MAINTENANCE START UP PROCEDURE 1. MAINTENANCE 2. 3. 4. 5. 6. 7. 8. Read all safety instructions. Decals on the Machete Boom warn you of particular and multiple hazards. Many decals are attached close to part of the Machete Boom where there is a possible hazard. Read and make sure you understand the safety messages before you operate the Machete Boom. Keep all decals clean and readable. Replace lost or damaged decals.
SEGURIDAD INFORMACIÓN DE PARTES SEGURIDAD INFORMACIÓN DE PARTES Las cortadoras RHINO usan balanciadas y componentes de systema seleccionado para los portadores de cuchillas, cuchillas, eje de cortar, navaja, suspensiones de navajas, los rodillos, los componentes de línea motriz, y cojinetes. Estas partes son echas y probadas a la especificaciones de RHINO. Partes que no son auténticas no regularmente llegan con estas especificaciones.
SEGURIDAD SEGURIDAD RIESGOS CON EL MANTENIMIENTO DEL IMPLEMENTO MANTENGA LOS IMPLEMENTOS EN BUENAS CONDICIONES DE FUNCIONAMIENTO, A TRAVÉS DE UN SERVICIO, REPARACIÓN O MANTENIMIENTO APROPIADO. ANTES DE REALIZAR TAREAS DE SERVICIO, REPARACIÓN Y MANTENIMIENTO DEL IMPLEMENTO: • APAGUE EL MOTOR Y EL PTO, coloque el freno de mano, descienda el implemento, espere a que se detengan todas las partes móviles y quite la llave antes de bajarse del tractor.
SEGURIDAD RIESGOS EN TRANSPORTE SEGURIDAD PARA EVITAR LESIONES GRAVES O LA MUERTE AL REMOLCAR O TRANSPORTAR EQUIPOS: • MANTENGA la velocidad de transporte POR DEBAJO DE 20 millas por hora para mantener el control del equipo. • REDUZCA LA VELOCIDAD en terreno inclinado, en las curvas y en condiciones de remolque desfavorables. • NO REMOLQUE camiones u otros vehículos • USE un tractor de tamaño adecuado y equipado en función del equipo de remolque. • SIGA todas las reglamentaciones de tránsito locales.
SEGURIDAD SEGURIDAD RIESGOS ELÉCRTICOS Y DE FUEGO PARA EVITAR LESIONES GRAVES O LA MUERTE POR CONTACTO ELÉCTRICO AL TRABAJAR CERCA DE CABLES ELÉCTRICOS, LÍNEAS DE GAS Y DE SERVICIOS: LLAME AL 811 y al 1-800-258-0808 para identificar cables de servicios subterráneos. • NO ponga en contacto la cortadora con ninguna estructura u obstrucción de servicios o municipales.
SEGURIDAD RIESGO DE FILTRACION DE ACEITE HIDRÁULICO DE ALTA PRESIÓN SEGURIDAD PARA EVITAR LESIONES GRAVES O LA MUERTE POR PENETRACIÓN DE FILTRACIONES DE ACEITE HIDRÁULICO DE ALTA PRESIÓN: • NO OPERE el equipo con filtraciones de aceite o combustible. • MANTENGA todas las mangueras hidráulicas, líneas y conexiones en BUEN ESTADO y AJUSTADAS antes de aplicar presión al sistema. • LIBERE LA PRESIÓN HIDRÁULICA antes de desconectar las líneas o trabajar en el sistema.
SEGURIDAD SEGURIDAD RIESGO DEL CONTACTO A LAS CUCHILLAS DE CORTADORA MANTÉNGASE LEJOS DE LAS CUCHILLAS GIRATORIAS PARA EVITAR LESIONES GRAVES O LA MUERTE POR CONTACTO CON LA CUCHILLA: • • • • • MANTÉNGASE LEJOS y NO ACERQUE LAS MANOS, LOS PIES y EL CUERPO a las cuchillas giratorias, líneas de conducción y partes hasta que todos los elementos móviles se hayan detenido.
SEGURIDAD RIESGO DE ENREDO POR EL PTO SEGURIDAD MANTÉNGASE ALEJADO DE LAS LÍNEAS DE CONDUCCIÓN Y OTROS ELEMENTOS GIRATORIOS PARA EVITAR LESIONES GRAVES O LA MUERTE: MANTÉNGASE LEJOS y NO ACERQUE las manos, los pies y el cuerpo a las cuchillas giratorias, líneas de conducción y partes hasta que todos los elementos móviles se hayan detenido.
SEGURIDAD SEGURIDAD RIESGO DE ATROPELLO PARA EVITAR LESIONES GRAVES O LA MUERTE POR CAÍDA DEL TRACTOR O ATROPELLO DEL EQUIPO: Cuando no esté cortando, coloque el brazo y el cabezal de la cortadora en el espacio de transporte antes de moverse. • NUNCA LLEVE A OTRAS PERSONAS en el tractor o implemento. • SÓLO OPERE el tractor y el equipo sentado en el asiento del tractor. • SIEMPRE ABRÓCHESE el cinturón de seguridad al operar el tractor y los equipos.
SEGURIDAD RIESGO DE OBJECTOS LANZADOS Continuado NO exceda la capacidad de corte nominal de la cortadora, ni corte elementos que no sean vegetación. USE CABINAS DE TRACTOR CERRADAS cuando haya dos o más cortadoras operando en un mismo sector. No opere la cortadora en áreas susceptibles al ataque de abejas o insectos, salvo que USE PRENDAS PROTECTORAS o una cabina de tractor cerrada. AJUSTE el cabezal de la cortadora paralelo al suelo y cerca de él sin exponer las cuchillas.
SEGURIDAD SEGURIDAD RIESGO DE OBJECTOS LANZADOS LAS CORTADORAS GIRATORIAS PUEDEN ARROJAR OBJETOS A 90 METROS (300 PIES) O MÁS EN CONDICIONES ADVERSAS.
SEGURIDAD CONECTAR O DESCONECTAR EL IMPLEMENTO DE SEGURIDAD SEGURIDAD PARA EVITAR LESIONES GRAVES O LA MUERTE POR APLASTAMIENTO POR EL TRACTOR O IMPLEMENTO: CUANDO conecte el cabezal de la cortadora al brazo: • MANTENGA A LOS TRANSEÚNTES LEJOS del tractor y la cortadora.
SEGURIDAD SEGURIDAD RIESGO DE APLASTAMIENTO PARA EVITAR LESIONES GRAVES O LA MUERTE POR CAÍDA DEL TRACTOR O ATROPELLO DEL EQUIPO, VUELCO O APLASTAMIENTO POR LA CAÍDA DE DEL BRAZO O EL IMPLEMENTO: • • • • USE tractores equipados con SISTEMA ANTIVUELCO (ROPS) y CINTURONES DE SEGURIDAD para las operaciones de corte. MANTENGA EL SISTEMA ROPS trabado en posición vertical. SIEMPRE ABRÓCHESE el cinturón de seguridad al operar el tractor y los equipos.
SEGURIDAD SEGURIDAD DEL OPERADOR LEA, COMPRENDA y SIGA las instrucciones del Manual del Operador, al igual que las Advertencias y Mensajes de Seguridad. USE GAFAS DE SEGURIDAD, calzado protector, casco, protección auditiva y guantes al operar o reparar el equipo USE un aparato de respiración apropiado al operar en condiciones polvorientas a fin de evitar contraer enfermedades respiratorias. NO USE prendas sueltas o joyas que se puedan enredar con las partes giratorias y causar una lesión.
SEGURIDAD SEGURIDAD INSTRUCCIONES DE SEGURIDAD Y PRÁCTICAS GENERALES El mejor operador es un operador cuidadoso. La seguridad es de importancia fundamental para el fabricante, y también debería serlo para el propietario u operador. La mayoría de los accidentes se pueden evitar prestando suma atención al equipo, al ambiente circundante, y tomando algunas precauciones.
SECCIÓN DE SEGURIDAD Sección de Seguridad 1-1 © 2011 Alamo Group Inc.
Instrucciones de operaciones antes de la entrega del DISTRIBUIDOR al CLIENTE El distribuidor deberá informar al comprador de este producto las condiciones, disposiciones y procedimientos de garantía aplicables; informar la responsabilidad del comprador de capacitar a sus operadores para la operación segura; revisar el contenido del Manual del Operador, incluido el equipo de seguridad, la operación segura y el mantenimiento; y revisar las Señales de Seguridad que se encuentran en el implemento (y en el tract
Alamo Group Ag.
A fin de reducir la tasa de accidentes y mejorar la operación segura de las cortadoras, Alamo Group Ag Division se ha asociado con otros fabricantes de la industria para desarrollar el video y la guía de Prácticas de Seguridad para Cortadoras Industriales y Agrícolas AEM/FEMA. El video explica a los operadores de tractores y cortadoras las prácticas seguras que deben adoptar cuando utilizan cortadoras industriales y agrícolas.
Al propietario/operador/distribuidor Este Manual del Operador es una parte esencial de la operación segura de esta máquina y se debe mantener con la unidad siempre. El implemento incluye un porta manual donde se puede guardar el manual de manera adecuada. Si el manual se extravía o se daña, puede solicitar otra copia sin cargo a un distribuidor autorizado de Rhino o descargarlo del sitio web de Rhino (www.servis-rhino.com).
Publicado en 06/11 SERVIS 2160 CORTADORA CON BRAZO HYDRÁULICO Parte nº. 00765708C MANUAL DE OPERADOR Este Manual del Operador es una parte esencial de la operación segura de esta máquina y se debe mantener con la unidad siempre. LEA, ENTIENDA, y SIGA las Instrucciones de Seguridad y Operación contenidas en este manual antes de operar el equipo. C01-Cover SP RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com $0.00 ©2011 Alamo Group Inc.