Industrial LTE CPE User Manual V1.3.
Before Use Steps: 1. Remove bottom cover 2. Insert Micro SIM card into card socket(yellow frame) Power 12~24V 3. Connect power cable and LAN cable LAN * Please wear anti-static gloves and always remove/insert micro SIM card when the device is power off. RP131CBRS-P User Manual v1.
Configure Laptop/PC Ethernet to Fixed IP To connect to video bridge, please use fixed IP all the time no matter in configuration or assigned IP check period. Steps: 1. Configure Laptop IP to 10.10.2.10/255.255.255.0 (Don’t use DHCP to get IP from CPE) 2. Click “OK” RP131CBRS-P User Manual v1.
How to Login GUI 1. Visit https://10.10.2.254 2. User ID/PW: admin/admin Steps: 1.Visit https://10.10.2.254 2.User ID/PW: admin/admin 3.Click “Sing In” RP131CBRS-P User Manual v1.
How to Get LTE information 1. Visit https://10.10.2.254 2. Click ”Status” LTE information Steps: 1.Visit https://10.10.2.254 2.Click “Status” on the left menu Sercomm FW version RP131CBRS-P User Manual v1.
How to configure APN Name-NAT 1. Visit https://10.10.2.254 2. Click ”Setting” 3. Configure APN name 5. Click ”Restart” to reboot device Steps: 1.Visit https://10.10.2.254 2.Click “Setting” on the left menu 3.Configure APN Name if required 4.Click ”Save” 5.Click “Restart “ or unplug to reboot the device 4. Click “Save” RP131CBRS-P User Manual v1.
How to configure APN Name-Bridge 1. Visit https://10.10.2.254 2. Click ”Setting” 3. Configure APN name 5. Click ”Restart” to reboot device Steps: 4. Click “Save” RP131CBRS-P User Manual v1.3 6 1.Visit https://10.10.2.254 2.Click “Setting” on the left menu 3.Tick the checkbox of Bridge and configure APN Name if required 4.Click ”Save” 5.Click “Restart “ or unplug to reboot the device 6.Configure laptop/PC ethernet to DHCP to get IP in bridge mode. 7.
How to Upgrade Firmware 1. Visit https://10.10.2.254 2. Click 3. Click to choose firmware file 4. Click “Upload” Steps: 1.Visit https://10.10.2.254 2.Click “Administration” on the left menu 3.Click “Choose File” to choose firmware file 4.Click ”Upload” RP131CBRS-P User Manual v1.
How to Reset to Default 1. Visit https://10.10.2.254 3. Click “Config File” 2. Click 4. Click “Factory Defaults” 5. Click ”Restart” to reboot device Steps: 1.Visit https://10.10.2.254 2.Click “Administration” on the left menu 3.Click “Config File” 4.Click “Factory Defaults” to reset to default settings 5.Click “Restart “ or unplug to reboot the device RP131CBRS-P User Manual v1.
How to Read LEDs STATUS LED LTE SIGNAL LED STATUS Green Red Blue Green Orange Power On On Off Off Off Off Power Off Off Off Off Off Off No SIM card Off On Off Off Off Blink Off Off Off Off FW Upgrading Fail On Blink Off Off Off PLMN Search / Network Attaching On Off Off Blink Off RSRP (> -87) dBm On Off On Off Off RSRP ( -106 ~ -87) dBm On Off Off On Off RSRP (< -106) dBm On Off Off Off On FW Upgrading RP131CBRS-P User Manual v1.
How to Mount the Device_Pole Mount RP131CBRS-P User Manual v1.
How to Mount the Device_Wall Mount RP131CBRS-P User Manual v1.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
