Manual Part 2

ManualsBrandsSercomm ManualsElectronics802.11g Wireless mini-PCI LAN Card

Table Of Contents

UNINSTALLATION

Mode

You can select IEEE 802.11b(B-Only), 802.11b

+(B-Plus) , 802.11g (G-Only)standard or B&G Mode

(If you choose this option the device will automatically

convert the suitable standard ).

Profile

Enter the profile name and click the Save

utton to save your configuration, To open the

rofiles you saved, select the profile from the

pull-down menu and then click the Load

button. To delete the profiles you saved, select

the profile from the pull-down menu and then

click the Delete button.

Tx Power Level

Transmit power level, includes Low Power,

Medium-Low Power, Medium Power,

Medium-High Power, High Power

Fragment Threshold To fragment MSDU or MMPDU into small sizes of

frames for increasing the reliability of frame (The

maximum value of 4096 means no fragmentation is

needed) transmission. The performance will be

decreased as well, thus a noisy environment is

recommended.

RTS Threshold This value should remain at its default setting of

4096. Should you encounter inconsistent data

flow, only minor modifications of this value are

recommended.

21 -

Summary of content (12 pages)

PAGE 1
Mode Profile Tx Power Level Fragment Threshold RTS Threshold You can select IEEE 802.11b(B-Only), 802.11b +(B-Plus) , 802.11g (G-Only)standard or B&G Mode (If you choose this option the device will automatically convert the suitable standard ). Enter the profile name and click the Save button to save your configuration, To open the profiles you saved, select the profile from the pull-down menu and then click the Load button.
PAGE 2
Preamble Retry limits A preamble is a signal used in wireless environment to synchronize the transmitting timing including Synchronization and Start frame delimiter. (Note: If you want to change the Preamble type into Long or Short, please check the setting of AP.) You can set the number of retries if no acknowledgement appears from the receiving station. Advanced Tab The Advanced tab displays the current status of the Wireless Network Adapter.
PAGE 3
If you checked External Configuration in the Main tab (see page 18), functions in the following figure will be disabled. Privacy Mode Configure your NONE, WEP, CCX, 802.1x and WPA settings： NONE：No security defined. WEP (Wired Equivalent Privacy) is a data security mechanism based on a 40 Bit/128 Bit/256 Bit shared key algorithm. Press the Cofigure button to change WEP configuration. CCX （ Cisco Compatible Extension ） .
PAGE 4
provides user-based, centralized authentication, as well as per-user wired equivalent privacy (WEP) session keys. Press the Configure button to change CCX configuration. The 802.1X Configuration window is used to configure WEP, CCX and WPA security with 802.1X authentication. WPA（WiFi Protected Access）encryption can be used to ensure the security of your wireless network.
PAGE 5
Encryption 1-4 Key size To configure your WEP settings. WEP (Wired Equivalent Privacy) encryption can be used to ensure the security of your wireless network. Select one Key and Key Size then fill in the appropriate value/phrase in Encryption field. Note: You must use the same Key and Encryption settings for the both sides of the wireless network to connect KEY1 ~ KEY 4：You can specify up to 4 different keys to decrypt wireless data. Select the Default key setting from the radio button.
PAGE 6
Protocol This panel enables you to select an authentication protocol. Password This panel is available when EAP-TLS is not selected (either MSCHAP V2 over PEAP is selected with WEP or LEAP is selected for CCX). This panel enables you to enter a login name and password or request that the driver prompt for them when you connect to a network. Personal Certificate This panel is available when EAP-TLS protocol is selected and enables you to select a certificate for authenticating the station.
PAGE 7
802.1x： EAP-TLS EAP-TLS is a mutual authentication method, which means that both the client and the server prove their identities. LEAP Network administers have been taking advantage of the simplified user and security administration that LEAP provides. Before the security authentication is started, you should enter the user name and password or the authentication process will fail.
PAGE 8
WPA settings Preshared Key： Passphrase：Enter the key that you are sharing with the network for the WLAN connection. 802.1x：You may refer to page 25(802.1x Configuration).
PAGE 9
Statistics Tab The Statistics Tab displays the available statistic information including Receive packets, Transmit packets, Association reject packets, Association timeout packets, Authentication Authentication timeout packets.
PAGE 10
About Tab Click on the About tab to view basic version information about the OS Version, Utility Version, Driver Version, Firmware Version and EEPROM Version.
PAGE 11
UNINSTALLATION In case you need to uninstall the Utility and driver, please refer to below steps. (As you uninstall the utility, the driver will be uninstalled as well.) 1. Go to Start Programs LAN Utility. WLanUtility Uninstall Wireless 2. Click OK to continue. 3. Select Yes, I want to restart my computer now, and then click Finish to complete the uninstalled procedure.
PAGE 12
- 32 -