WTU-518 USER MANUAL Rev 30-2015 Page 1
To contact Sercel Europe Nantes, France Sales; Customer Support; Manufacturing & Repair. B.P. 30439, 16 rue de Bel Air 44474 Carquefou Cedex Tel: +33 2 40 30 11 81, Fax: +33 2 40 30 19 48 Hot-Line: Land: +33 2 40 30 58 88 Marine: +33 2 40 30 59 59 Navigation: +33 2 40 30 69 87 E-mail: sales.nantes@sercel.com customersupport.land@sercel.com customersupport.marine@sercel.com customersupport.navigation@sercel.com repair.france@sercel.com streamer.repair@sercel.com www.sercel.
Guidelines for Safe and Efficient Use: Read this information before using your WTU-518. Warnings, Cautions, and Important notices throughout this manual guide you to avoid injury, prevent equipment damage, and determine equipment use when varying components or configurations exist. Notes provide tips or additional information. SERCEL is not responsible for damages or injuries that result from failure to observe the information provided.
TABLE DES MATIERES : DESCRIPTION: ............................................................................................................................................................................. 5 DEPLOYMENT: ............................................................................................................................................................................ 6 LEDS FUNCTION: ....................................................................................................
Description: WTU-518 The WTU-518 acquires and stores data coming from the analog or digital sensor plugged on its geophone connector. By WLAN or LAN communication links, the WTU-518 transmits these stored data to recorder or field unit’s equipment. State Of Health are transmitted through the UNITE system via a 2.4GHz radio communication link. 2.
Deployment: IMPORTANT Whenever any connector is unused, put its connector protective cap in place. LEDs Function: Two LEDs flashing in red Two LEDs flashing every 1s in green Two LEDs flashing every 4s in green acquisition not started or issue after TTFF timeout Harvest and acquisition is running. GPS is locked or unlocked. Acquisition is running. GPS is locked.
Configuring the WTU-518: The user has to program WTU-518 parameters. In this version of document, only the GPS, WLAN and radio configuration are described.
Set Radio Regulatory Domain: Use this menu to choose the appropriate maximum radiated output power for compliance with the local regulations of the country in which the radio unit is to be used: • CE for Europe: +13 dBm eirp at 100 kbps and 500 kbps • FCC/RSS for US/Canada: +16 dBm eirp at 100 kbps and 500 kbps Set Radio frequencies: Use this menu to choose one of these sets of frequencies used in the Frequency Hopping Spread Spectrum (FHSS): 2405-2469 hopset #1 : full 2.
Use the Synchro Word key to prevent connection to another Sercel network. The radio packets transmitted with a Synchro Word key cannot be received by a Sercel network configured with another Synchro Word key.
IMPORTANT Prior to connecting any plug, make sure there is no water inside connectors. Electrostatic discharge: Use the following guidelines to provide a static-free repair station that will preclude any ESD-related damage to electronic circuits: • All spare parts (circuit boards and ESD sensitive devices) should be stored and transported in staticshielding bags. • Unless the repair station rests on a conductive floor, chairs or stools should rest on a grounded, rigidtype, static-dissipative floor mat.
Repairs: WTU-518 disassembly instructions: To disassemble the WTU-518, remove the 8th screws visible when the unit is resting upside down. CAUTION Rev 30-2015 Pay attention to not pull on the internal battery’s cables when disassemble the battery’s part with the lid.
Internal battery replacement: Disconnect the battery’s connector from the WTU-518‘s board and then, remove the 4th screws placed on the clamping plate: Remove the holding foam to access the internal battery CAUTION Pay attention of the insertion ‘direction of the internal battery. CAUTION Use only the type of battery specified by Sercel.
Fuse replacement: CAUTION Before to change the out of service fuse, unplug the external battery from the WTU-518 A. The WTU-518 A has one fuse placed on the hot point on the main board of the WTU-518 A WTU-518 A Main board fuse access: To access to the fuse placement, disconnect the connectors described below, and then remove the electronic set from the lid: Power / Ethernet connector Input Connector Internal battery connector Replace the out of service fuse by a new fuse.
WTU-518 connectors: Power / Ethernet connector: Power / Ethernet plug A B Signal Name +VBAT GND I/O type In In C Reset_dongle In D Ethernet_dongle In E TX+ Out F TX- Out G RX+ In H RX- In Other signal Input geophone connector: Input geophone plug Femelle Male Rev 30-2015 Signal Name Input_n Input_p I/O type In-Out In-Out Other signal 0V in digital mode +5.
Specifications: Operating Voltage 11 – 16.8 Vdc Current consumption up to 2.
Regulatory Information: US: The FCC ID of the WTU-518 is KQ9-0500A The WTU-518 contains FCC ID: KQ9-W161A This device complies with part 15 of the FCC Rules.
CANADA: The IC ID of the WTU-518 is 1317A-0500A CAN ICES-3 (A) / NMB-3(A) The WTU-518 contains IC ID: 1317A-W161A This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
Europe: Conforms to the essential requirements of the following EEC directives: R&TTE 1999/5/CE EMC 2004/108/CE LV 2006/95/CE WARNING The WTU-518 is a class-A device. In residential areas, the user may be requested to take appropriate measures in the event of RF interference caused by this device.