Installation and Operation Guide Installation and Operation Guide DMR Repeater SBR8040/SCR8040/SER8040 1
Installation and Operation Guide General This guide contains the installation and basic operating instructions for the DMR Repeater models SBR8000, SCR8000 and SER8000. This guide does not contain information relating to the installation of accessories such as the antenna and duplexer. Refer to the installation instructions supplied with these accessories for further safety and installation instructions. Disclaimer notice Sepura’s policy is to continually improve its products.
DMR Repeater SBR8000, SCR8000, SER8000 Safety Read these safety instructions carefully. Attention! This product is restricted for occupational use and is not intended or authorised for use by the general population. It is the responsibility of the person operating the product to ensure that it is operated safely at all times, and that local laws and regulations governing the usage of Radio Frequency (RF) products are observed. Users must be trained to operate this product safely.
Installation and Operation Guide environment. The antenna should be installed and operated with minimum distance 1.0m from human body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
DMR Repeater SBR8000, SCR8000, SER8000 antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Installation and Operation Guide Technical specification Frequency Range ...................................................400-470 MHz Dimensions (WxDxH) ................. 482.5 x 338.5 x 132.5 mm (3U) Weight .............................................................................. 12.5 Kg Power Supply AC ............................... 100-120V@2.5A 50/60 Hz 200-240V@1.5A 50/60 Hz Power Supply DC........................................... 10.8 – 15.6V@15A DC Fuse ....................................
DMR Repeater SBR8000, SCR8000, SER8000 Front Panel Rear Panel 6
Installation and Operation Guide Controls, connectors and components Refer to the illustration for the location of the following controls, connectors and buttons.
DMR Repeater SBR8000, SCR8000, SER8000 Unpacking Accessory information 1 Sepura supply a range of accessories for this product. Contact your Service Provider or visit our website for a full list of accessories. Accessory 2 (1) DMR Repeater (2) Desk mount feet with screws (4 pieces) Unpack the contents of the box and ensure that all items are received in good condition. If any of the goods are damaged or not supplied, notify your Service Provider within 10 days of receipt of the equipment. 8 Part No.
Installation and Operation Guide Installation Wall-mount bracket installation Guidelines and recommendations It is important that the repeater does not exceed the working limits detailed in the technical specification section of this guide. When rack mounting the repeater, ensure sufficient air flow to prevent overheating and secure the unit within the rack system. Cabling should be carefully routed and secured to prevent connections becoming loose.
DMR Repeater SBR8000, SCR8000, SER8000 Hold the bracket securely, keeping it level. Secure into position using the ST6 x 35 expansion screws. Ensure that the bracket is secure and level. Remove the desk mount feet (if fitted) from the repeater. With the top of the repeater against the wall, slide the repeater into the bracket. Secure the repeater to the wall bracket using the four M5 x 12 screws as shown.
Installation and Operation Guide Connections must be positioned close to the DC power source positive terminal. All connectors are located on the back panel of the repeater. Ensure that the cables are routed so that they are kept well clear of the antenna cable. Route cables carefully to eliminate the possibility of damage by sharp edges. Ensure all cabling is secured and routed to avoid the risk of a trip hazard.
DMR Repeater SBR8000, SCR8000, SER8000 Basic operation Alarm mode Power on/off The Alarm indicator on the front panel illuminates when certain operational states warrant. When the repeater is in start-up mode, the LED remains illuminated for the duration of the startup routine (approx. 60 seconds). To switch the repeater on, operate the Power on/off switch. The Power on/off status indicator illuminates and the repeater runs a start-up test routine that takes approximately 60 seconds.
Installation and Operation Guide Caring for your product Duplexer specifications The product does not require regular servicing. Caring for your product as described in this guide will help maintain the product in good operational condition. Always wear eye protection when using brushes or other tools to clear debris from connectors or other parts of the product. Do not use chemicals, aerosols or abrasive cleaners. Chemical coatings must not be applied to any part of the terminal or battery.
Sepura plc Radio House St Andrew’s Road Cambridge CB4 1GR UK Tel: +44 (0)1223 876000 Fax: +44 (0)1223 879000 Sepura.