SEOWON INTECH
Contents 1. Multi User CPE Configuration and Connection 1.1 Product Introduction ---------------------------------------- 4 1.2 Packaging Contents ---------------------------------------- 5 1.3 Description of Product Functions -------------------------- 6 1.4 Network Configuration -------------------------------------- 8 2. Multi User CPE Connection 2.1 Wired Connection -------------------------------------------- 10 2.2 WiMAX Wired Connection (CPE) ------------------------ 12 3. PC Configuration 3.
7. Multi User CPE LAN Setup 7.1 DHCP Server Setup --------------------------------------- 39 7.2 MAC Address Setup -------------------------------------- 40 7.3 LAN Status Information ---------------------------------- 41 8. Application Support Setup 8.1 Firewall Setup ---------------------------------------------- 42 8.2 Firewall regulation Setup(Filter) ------------------------ 43 8.3 Port Forwarding -------------------------------------------- 44 8.
1. Multi User CPE Configuration and Connection 1.1 Product Introduction This product receives external WiMAX signals to construct in-building infrastructure on WiMAX network and is covered by Ethernet network internally. The product serves as a relay as well as a USB Modem and an internet router. But the product is purposed to supply to users, focusing on a relay part rather than a modem.
1.
1.3 Description of Product Function SEOWONINTECH LED Indicator Function PWR Power Supply status (On at Power ON) WiMAX Flashing at normal operation (Repeatedly ON/OFF at 0.
1.3 Description of Product Function MULTI USER CPE Rear Side Description Item External Antenna Details ANT1: WiMAX Diversity ANT2: WiMAX Main Separable external antenna User external type antenna attachable * Antenna Classification - 5: 2.5GHz Power S/W Power On/Off Switch (On/Off by pressing right or left) DC IN Power Adapter connection (DC 7.
1.4 Network Configuration Local Network External Network Gateway modem WiMAX WLAN Internet RJ45 PC To Verify normal operation of router LEDs You have to check if each LED of the router operates properly after connecting router, modem, and PC with LAN cable as follows:. SEOWONINTECH LED Normal Operation Actions to be taken at failure PWR ON when connecting adapter Check for adapter power failure WiMAX Flashing at 0.
1.4 Network Configuration If LED light is not in “normal operation”, check if there is any failure according to actions to be taken. Install a router after connecting to network. „ If normal connection between router and PC is checked, you have to set up PC and router. „ PC setup is to control network option such as Win98/2000/XP to enable to use Internet on condition that PC is connected to router. It is progressed by referring to Chapter II, depending on OS type.
2. Multi User CPE Connection 2.1 Wired Connection (WAN) 1) Connecting Power Adapter Connect Power Adapter to AC terminal and then connect DC connector. When turning the power switch on, only Power LED keeps lighting up and all other lamps are turned ON for about 1 second and then OFF. When booting is completed, WiMAX lamps of MULTI USER CPE are flashing at about 0.1 sec intervals. Always use the rated adapter of the product for a router. If not, it may cause malfunction and damage.
2.
2.
3. PC Configuration This chapter describes how to set up PC network environment by connecting to MULTI USER CPE according to Windows operating system. To use Internet under operating system such as Windows, the protocol called ‘TCP/IP’ is required. For normal use of MULTI USER CPE, you have to set up the TCP/IP protocol normally. In general, the condition Windows is installed first in PC is the condition router can be used, in which no separate TCP/IP setup is required.
3.1 Windows 98/ME Setup This procedure is to restore your Windows 98/ME TCP/IP settings to default values.
3.1 Windows 98/ME Setup < Select TCP/IP > < Select Obtain an IP address automatically > - Remove all gateways installed in Gateway. … - Choose “Disable DNS” from DNS Configuration.
3.1 Windows 98/ME Setup - When IP Address, Gateway, DNS Configuration setups are completed, click on ‘OK’ to close the TCP/IP Properties dialog box. When “Network” window is displayed, click ‘OK’ again. - In case of Windows 98, the system restarts automatically when network related setup is changed. When the ‘Change System Setup’ screen pops up, click ‘Yes’ to restart Windows. - When the PC is restarted, MULTI USER CPE assigns the IP address automatically.
3.1 Windows 98/ME Setup Select LAN card adapter used by connecting the router from the winipcfg IP Configuration window (Select NDIS 5.0 or the appropriate LAN card. Do not select PPP adapter) to check if the IP address of your PC is assigned to the value between 192.168.1.10 and 192.168.1.60 automatically. If you cannot see other LAN card than PPP adapter being used, you have to reinstall a LAN card driver.
3.2 Windows 2000 Setup This procedure is to restore Windows 2000’s TCP/IP setup to default values. If Windows is not installed for the first time in PC or Internet is not operated properly, check all values are normal according to the following. After completing the TCP/IP setup of PC, to check if IP address is obtained from MULTI USER CPE automatically, connect PC and MULTI USER CPE with a LAN cable according to the instructions of Chapter II and keep MULTI USER CPE turned on before Windows setting up.
3.2 Windows 2000 Setup
3.2 Windows 2000 Setup - You can check the automatic IP address assignment by using the ipconfig command from Command Prompt. - To run the Command Prompt, click the Start button on the lower left corner of Windows screen and click Run to enter “cmd” in the Open box, and then click OK button. When the Command Prompt runs, enter the “ipconfig” command to verify IP address, Subnet mask, and Gateway, which are automatically assigned to PC.
3.2 Windows 2000 Setup IP Address: 192.168.1.10~60 Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.1 [Note] If IP address is not assigned normally, check the following and restart PC so as to check if the IP address is assigned.
3.3 Windows XP Setup This procedure is to restore Windows XP’s TCP/IP setup to default values. If Windows is installed for the first time in PC, there is no change and check all values are normal according to the following. After completing the TCP/IP setup of PC, to check if IP address is obtained from MULTI USER CPE automatically, connect PC and MULTI USER CPE with a LAN cable according to the instructions of Chapter 2 and keep MULTI USER CPE turned on before Windows setting up.
3.3 Windows XP Setup - Double-click the Local Area Connection from the Network Connection to select. - Click Properties in the Local Area Connection Status to select.
3.3 Windows XP Setup - Double-click Internet Protocol (TCP/IP) and then select the Obtain an IP address automatically and Obtain a DNS Server address automatically.
3.3 Windows XP Setup - To run the Command Prompt, click the Start button on the lower left corner of Windows screen and click Run to enter “cmd” in the Open box, and then click OK button. When the Command Prompt runs, enter the “ipconfig” command to verify IP address, Subnet mask, and Gateway, which are automatically assigned to PC. [Note] All PCs connected to MULTI USER CPE will get each of assigned IP addresses respectively. IP Address: 192.168.1.10 ~ 60 Subnet Mask: 255.
3.3 Windows XP Setup To use Internet after completion of PC setup, refer to Chapter IV and set the WAN port of MULTI USER CPE to connect to the Internet. Since Internet connection setup is made by router, you don’t need to set up in all PCs but do just once. [Note] How to remove Internet access program when using ADSL. (Windows 98/ME, 2000) In case of PPPoE connection mode, automatic running of access program while on Internet Explorer can cause no appearance of setup screen.
3.3 Windows XP Setup [Note] How to remove the Windows XP broadband connection when using ADSL. Double-click the Start on Desktop – Control Panel – Network Connections to pop up. From the Network Connections window, right-click on the icon added in Broadband to “delete”. If not deleted, right-click on “Disconnect” and “delete” the icon.
4. Multi User CPE Internet Connection with Internet Setup Wizard This chapter describes how to connect MULTI USER CPE to Internet. Internet connection setup is made by accessing to internal web setup screen. Therefore, Internet connection setup can be done from one of PCs connected to the MULTI USER CPE by executing just once. To access to the web server built in the MULTI USER CPE, you have to set up PC normally. For details how to set up PC, refer to Chapter III of this manual.
4.1 Access to the Multi User CPE Built-in Web Server You can access to the web server built in the MULTI USER CPE, even in the environment not connected to Internet. To access to the web server, run Internet Explorer and input 192.168.1.1, the address of MULTI USER CPE, in the address box as shown below. [Note] If PC is connected to the MULTI USER CPE normally but not connected to Internet, only inputting the address of 192.168.1.
4.2 Running Multi User CPE Internet Setup Wizard If you click Wizard LINK at the top left from the initial screen of MULTI USER CPE, the following screen appears. The above screen provides the window to select Internet line. Two types of Internet connection are available depending on your selection. 1) Use Wired Connection (ADSL/VDSL or Cable Modem etc.): Wired Connection Mode Check the appropriate circle, and it allows wired setting in sequence as shown below.
4.2 Running Multi User CPE Internet Setup Wizard The following screen describes how to get the IP address. Do appropriate setup for ISP of three Modes. - Check the following circle, to obtain an IP address automatically. Press Next. - Select the following to use the static IP. - The following is used when using ADSL Modem and ID/Password are issued.
4.2 Running Multi User CPE Internet Setup Wizard - The following screen is to set up internal network managed by MULTI USER CPE. If there isn’t any particular problem, you can set up and use it as default. You can change its setup and use it when linking to and using external router and other settings are required. Press Next to proceed.
5. Multi User CPE WiMAX Connection and Setup 5.1 IP Address Setup This screen is to set the mode assigning the IP address from the WiMAX modem. You can not only assign the host name and domain name of MULTI USER CPE but also set the IP address to DHCP(Dynamic IP) or Static IP address.
5.2 WiMAX Modem Setup Browse The screen is to perform various settings for WiMAX modem. You can assign whether or not to use the PKM Authentication on the top and accordingly set the PKM Authentication mode, ID/Password, anonymous ID, and ISP Certificate in the MULTI USER CPE. At the bottom, you can assign to perform customized command at initial boot of WiMAX modem. It is used when any particular setup is required for base station (BS) by the corresponding ISP.
5.3 WiMAX Modem Status Information. This screen displays various kinds of information of WiMAX modem.
6. Multi User CPE WAN Connection and Setup 6.1 IP Address Setup This screen is to set the mode assigning the IP address of wired WAN connection. You can not only assign the host name and domain name of MULTI USER CPE but also set the DHCP/Static address or IP address for PPPoE mode.
6.2 MAC Address Setup This screen is to change the MAC address used for WAN access. If access setup is allowed only for the PC having specific MAC address depending on ISP, it is used to change to the appropriate MAC address.
6.3 WAN Status Information The screen shows all sorts of status information on WAN access.
7. Multi User CPE LAN Setup 7.1 DHCP Server Setup This screen is to perform all kinds of setup related internal LAN. First of all, you can assign the IP address of gateway and subnet mask to be used in the LAN that MULTI USER CPE manages. If you use the system by linking with external router, some cases may need setup change, otherwise you can use default value. The following describes setting up whether or not to use DHCP and detailed information.
7.2 MAC Address Setup This screen is to change MAC address used for internal LAN connection. In most of cases you can use default setup.
7.3 LAN Status Information This screen displays all sorts of status information on internal LAN.
8. Application Support Setup 8.1 Firewall Setup This screen is to set whether or not to use firewall. Using firewall enables to set MULTI USER CPE to being not affected by hacking from the outside, including Ping Flooding or DoS. Internal LAN PCs are usually isolated/protected from external Internet even though they do not use firewall, but it is preferable to use firewall to be ON as possible. Default value is set to using firewall.
8. Application Support Setup 8.2 Firewall regulation Setup(Filter) This Screen is to set whether or not to permission/block for specification site. The block setting up has three ways – by MAC address by IP address of the starting point, by IP address of destination.
8.3 Port Forwarding Port Forwarding function is used to set incoming connections on specific TCP/IP port from outside to being connected to the assigned PC. If you have to use programs, such as VoIP and P2P, or operate servers, such as HTTP and FTP, in a PC on internal LAN, connections from outside may be allowed when assigning IP address of the PC connected to the appropriate port area.
8. Application Support Setup 8.4 Port Trigger Port Trigger function is perceived TCP/UDP port number that is used in Application using Internet and automatically forward to the PC using currntly from port needed relevant application.
8.5 DMZ Setup DMZ setup is used to place specific PC outside the firewall that is managed by MULTI USER CPE in order to be connected to the outside. Such PC specified in the DMZ may give and take packets freely from the outside internet irrespective of firewall setup, but special attention to PC protect should be paid because it is not protected by MULTI USER CPE’s basic firewall and protective features.
8.6 UPnP Setup Universal PnP is used to allow setting dynamic network connection and whether or not to use ports in the PC supporting UPnP on internal LAN. When UPnP is activated, MULTI USER CPE is searched through Residential Gateway in the network environment of PC that supports UPnP and you can see the current UPnP related information on your PC.
8.7 VPN Passthrough Setup VPN (Virtual Private Network) function is used to get access to security network installed in a company or organization via Internet network. If there is a VPN Server outside and one has access to the VPN Server via Internet network by using MULTI USER CPE, this screen shows to activate security protocol supported by the appropriate VPN Server. Supportable protocols include IPSec, PPTP, and L2TP.
8.
8.9 DDNS Setup It can be used as fixed IP address by assigning domain name on automatically assigned Internet Protocol address.
9. Switch Setup 9.1 Switch Basic Setup This screen is to set up Switch Hardware that is used for MULTI USER CPE. You can set up VLAN at the top of the screen. VLAN setup is used when operating 4 internal LAN ports of MULTI USER CPE in a group and separately. Values between 1 and 4096 can be assigned for VLAN and each VLAN may get meaningful name. VLAN supports the tagged/untagged mode.
9.2 Switch Advanced Setup This screen is used to set up the advanced features of MULTI USER CPE Switch Hardware.
9.3 Switch Debug Setup R100의 디버깅을 위한 설정을 할 수 있습니다.
9.4 Switch Status Information In this screen, you can see all sorts of statistics information on network transmission by each port of switch.
10. Administrator Function Setup 10.1 Administrator Password Setup This screen is to set up Password to be given to Administrator who manages all setups of MULTI USER CPE. Default password is “admin” and by changing the default password she/he can input and use the password set up every time she/he gains first access to web interface.
10.2 Factory Default Setup This screen is to reset all setups to Factory Default values. Please reboot for normal operation.
10.3 Firmware Upgrade Browse The screen is used for Firmware Upgrade. If there is a Firmware Upgrade file, press the Browse button to select and press the Upgrade Now button to start Firmware transmission and Upgrade. It takes about 2-3 minutes for Firmware Upgrade. And please pay attention because interruption during upgrade may cause damage to or malfunction of MULTI USER CPE.
10.4 System Log Browse R100의 인터넷 연결 중의 모든 트래픽 정보를 저장합니다.
11. WCM 11.1 Software Installation • Caution before Installtion. -Connect the USB modem to your PC before installing the software. When the modem is connected. “New Hardware Detect” window appears. Then User may ignore this window or click “Cancel” button. - If you have previous WCM Version, uninstall it first (See figure below) • Connect the USB Modem to your PC before installing the software. 1) Please insert WiMAX modem CD into CDROM Drive. When the Setup Menu Screen appears.
11. WCM 11.1 Software Installation Install Driver. Wait for 1~2 minite. Clicik [Install] button. Click [Next] button. Click [Finish] button. 2) Verification : Select [Start] – [Control] – [System] – [Hardware] – [Window device Manager]. You may verify the driver in device manager.
11. WCM 11.2 How to use WCM 1) Running WCM. - To start WiMAX Connection manager. Select [Start] > [Program] > [SEOWON] > [SEOWON WIMAX] > [SEOWON WIMAX CM] - Click icon. 2) Display Window. - Main Screen User can see the antenna icon about Antenna sensitivity, button about Connection / Disconnection / Menu / Help Icon.
11. WCM 11.2 How to use WCM - Help Menu Click [Help Menu] then popup menu appears. 1) Contact Us 2) Seowonintech Info : User can see to the seowonintech Homepage 3) Engineer Mode : Appear Engineer mode.
11. WCM 11.2 How to use WCM - Main Screen Click [MENU] then popup menu appears. 1) Connection : When user clicks this button, user can connect to internet by Auto and Windows start * Auto Connection : When WCM is launched, internet is connected Automatically * Window Start Connection : When Windows OS is launched, WCM is executed Automatically. 2) Connection Info : Click [Connection Info] in MENU. User can see Connection / Network / Program Information.
11. WCM 11.2 How to use WCM - Switch from Main Display into Tray Icon Click [ _ ] Icon in Main Display, WCM will be running in Tray mode. Connected - Switch from Tray Icon into Main Display Click [ x ] Icon in Main, WCM will be moving to Tray mode.
11. WCM 11.
11. WCM 11.
11. WCM 11.2 How to use WCM 5) WiMAX Exit - If Click [Disconnected] button in Main Screen, the state of WCM is Stand-by mode Program exit in Main Screen. Click [Exit] in [MENU] Program Exit in Tray Menu Click the right button of mouse in Tray icon, Popup menu appears. Then Select [Exit].
12. References 12.1 LAN CABLE Standards LAN Cable includes straight cable (direct cable) and cross cable. MULTI USER CPE has Cable Auto Sense feature, so either of the two can be used. However, it is not possible of normal communication if you use the cable that does not maintain the #1-2 and 3-6 twisted pairs according to the regulations. Always manufacture or purchase regulation cables to use.
12.2 IP Router PING Test Method PING Test through router in the PC shows whether PC is normally connected to IP router or not. You must check if the IP address of your PC is normal before PING Test. To perform a PING Test, run MS-DOS in Win98/ME, while Command Prompt in Windows 2000/XP. To do this, click the “Start” button at the lower left on the Windows screen and select “Run”.
12.3 Product Specification Parameter Description Parameter Description WiMAX System Profile IEEE 802.16e, Wave 1 compliant Receiver Noise Figure Under 7dB @ High Gain Mode Multiple Access OFDMA RF Sensitivity -88dBm @QPSK1/2 Frequency Band 2.5GHz UICC UICC Support(1.8/3.0/5.0V) Maximum RF Output 23dBm(200mW) SAR Limits Comply with FCC regulation Antenna Enternal 2 ANT (1 ANT Gain = 5dBi) Power Host Power 3.
12.4 Actions to be taken when internet is disconnected 1. Check the status of external type modem. : Check if Link lamps of cable, VDSL, ADSL modem is turned ON. 2. Check the LED status of MULTI USER CPE. 1) Check if POWER LED is turned ON. 2) Check if WAN lamp is turned ON. 3) Check if LEDs of WiMAX are turned ON. 4) Among No. 1, 2, 3, 4 LAN ports, check if the lamp of the port connected to PC is turned ON. 3. Check the IP address of PC.
12.4 Actions to be taken when internet is disconnected 3) In case of Windows XP ① Execute [Start -> Control Panel -> Network and Internet Connection], double-click [Local Area Connection], and click [Properties]. Click Properties of [Internet Protocol (TCP/IP)] among Components. ② Click [Use the follwing IP address]. ③ Enter [192.168.10.100] for [IP Address], [255.255.255.0] for [Subnet Mask], and [192.168.1.1] for [Default Gateway]. ④ Click [Use the following DNS Server Address].
12.5 Product Warranty and Customer Support Product Warranty Product Name: Gateway Modem Model Name: SWC-1104 This product comes with a one-year warranty and its compensation will be based on the following: Contents of Warranty Rules 1. Equipment for Warranty: MULTI USER CPE 2. Warranty Period: 1 year 3. Free repair service - If a defect or failure of the product occurs within the warranty period 4.
Regulatory Notices The SWC-1104 WiMAX complies with U.S. Federal Communications Commission (FCC) guidelines respecting safety levels of radio frequency (RF) exposure for portable devices, which in turn are consistent with the following safety standards previously set by U.S and international standards bodies: - ANSI / IEEE C95.
