User's Manual

ManualsBrandsSensus Metering Systems ManualsElectronicsUtility Meter Transceiver

AMR-XXX

Sensus RadioRead

Model 510R2 – Non Pit Unit

Installation Instructions-Draft

Page 1 of 4

The following information contains installation instructions for the

Sensus Model 510R2 MXU.

Note: This installation sheet is only for installation of the Sensus

Model 510R2. For instructions on installing other AMR devices,

please request and refer to the individual installation instruc-

tion for those devices.

The Model 510R2 MXU is designed for non pit, non submersible

applications and is available for both a single port and dual port

operation. The Model 510R2 can be mounted indoors or outdoors

where it is not subject to submergence. The Model 510R2 is not

intended for outdoor meter pits or vaults. The unit can be installed

with either a TouchCoupler connection or wire connection. Please

refer to AMR-326 for compatibility.

1. Sensus TouchPad

2. TouchPad Cover Assembly Complete

3. TouchPad Cover

4. TouchPad Fastener

5. TouchPad Cover Locking Clip

6. Model 510R2 Radio (Front View)

7. Model 5102 Radio TouchCoupler Enabled Assembly

(Rear View with TouchPad Cover)

Single Port – TouchCoupler Installation

1. Perform a TouchRead on TouchPad(s) to insure TouchRead to

the encoder works.

2. Taking a completely assembled Model 5102 Radio and Touch-

Coupler Spacer with TouchPad Cover, align the TouchPad

Cover over an installed Sensus TouchPad.

Important

General Information

Deﬁnitions

TouchCoupler - Installation Instructions

3. Place the unit over the TouchPad and press ﬁrmly until secure.

4. For additional support (optional), open the MXU door and pre-

drill the holes designed to fasten the unit to the wall. (Fastener

holes are located above the battery).

5. Secure the unit to the wall with screws.

6. Once unit is secured with the screws, close the door of the

MXU and tighten security screw until unit is ﬁrmly sealed.

7. Once the unit is closed and secured, begin the activation

process. (See Activate Radio section).

8. Coil excess wire and then secure to the body of the meter or

service line in a presentable manner.

Single Port - Remote TouchCoupler

Installation

Remote TouchCoupler installations are an option when a direct

TouchCoupler (Sensus only) connection cannot be completed due

to physical limitations. Before proceeding with the installation of a

remote TouchCoupler application, be sure to ﬁnd a location free

from obstacles that would interfere with the connection from the

TouchPad Cover to the MXU.

●

Wire stripping tool

●

Screwdriver - Small standard head for terminal connections

●

SR II security screw socket with 1/4" nut driver or ratchet wrench

●

Power drill and bit (1/4")

●

8 x 1" sheet metal screws

1. Find a suitable location for the installation where the TouchPad

Cover and MXU installation will be free from interference.

Note: If TouchPad is not already installed, install TouchPad allowing

enough room for the TouchPad Cover to be securely placed over

the installed TouchPad.

Recommended Tools and Materials

amr_321.fm Page 1 Tuesday, July 18, 2006 3:55 PM

Summary of content (4 pages)

PAGE 1
amr_321.fm Page 1 Tuesday, July 18, 2006 3:55 PM AMR-XXX Installation Instructions-Draft Sensus RadioRead Model 510R2 – Non Pit Unit 3. Place the unit over the TouchPad and press firmly until secure. Important The following information contains installation instructions for the Sensus Model 510R2 MXU. Note: This installation sheet is only for installation of the Sensus Model 510R2.
PAGE 2
amr_321.fm Page 2 Tuesday, July 18, 2006 3:55 PM AMR-XXX Installation Instructions-Draft Sensus RadioRead Model 510R2 – Non Pit Unit 2. Perform a TouchRead on TouchPad(s) to insure TouchRead to the encoder works. 3. Place the remote TouchPad Cover firmly over the Sensus TouchPad until secured. 4. Once the TouchPad Cover is secured on the TouchPad, find a location close to the TouchPad Cover to install the MXU. 5.
PAGE 3
amr_321.fm Page 3 Tuesday, July 18, 2006 3:55 PM AMR-XXX Sensus RadioRead Installation Instructions-Draft Model 510R2 – Non Pit Unit Note: Note: Red and black wires are non-polarized. 7. Black Green Touch Coupled PORT 1 Red Black Blue BATTERY PORT 2 Red Sensus Metering Systems Uniontown, PA 15401 Model 510R Pt. No. 539-61-537-51006T RadioRead M510R-D2-CMB-CMB-T Patent Pending.
PAGE 4
amr_321.fm Page 4 Tuesday, July 18, 2006 3:55 PM AMR-XXX Installation Instructions-Draft Sensus RadioRead Model 510R2 – Non Pit Unit 2. Once in Programmer Mode, pictured below, use the Up/Down arrows until ENABLE is displayed. 3. Place the TouchReader+ Sensor on the Programming port of the radio and press the Read button. This will send a message to the radio to start the activation process. Keep TouchReader+ in place until complete – messages will appear on the screen. 4.