User Instructions

CREATING A NEW WIRELESS NETWORK*
• Presspush-button5times.
• TheLEDclosesttothepush-buttonwillblink5timestoindicateitissearching
foraclearRFchannel.
• Whenachannelhasbeenselected,theLEDwilltransitiontosetsofthreeblinks,
indicatingthatthenewnetworkallowsjoiningfor15minutes.
• ContinuetothenextwirelessTransceiver/Bridgeandpressthebuttontwotimes.
• The LED will ash back sets of two blinks while it searches for a joinable
wirelessnetwork.
• Whenonehasbeenfound,theLEDwillagaintransitionbacktosetsofthree
blinks,indicatingthenetworkallowsjoiningforanother15minutes.
• Oncealldesireddevicesareadded,pressthebutton4timesonanyTransceiver/
Bridge in the newly commissioned network to disallow joining and return all
networkTransceiverLEDstonormaloperation.
JOINING AN EXISTING WIRELESS NETWORK*
• Pressbutton3timesonanyTransceiver/Bridgeonthedesirednetwork.
• Afteramoment,allTransceiver/Bridgesonthenetworkwillashthethreeblink
“allowjoining”patternfor15minutes.
• Continuetothenextwirelessdeviceandpressthebuttontwotimes.
• TheLEDclosesttothepush-button will ash back sets of two blinks while it
searchesforthejoinablewirelessnetwork.
• Whenfound,theLEDwilltransitionbacktosetsofthreeblinks,indicatingthe
networkwillallowjoiningforanother15minutes.
• OncealldesiredTransceivers/Bridgesareadded,pressthebutton4timesonany
wirelessinthenewlycommissionednetworktodisallowjoining.
NOTE
 THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO
THIS EQUIPMENT.   SUCH MODIFICATIONS COULD VOID THE USER’S
AUTHORITYTOOPERATETHEEQUIPMENT.
GENERAL INFORMATION
EachRJ-45portonaTransceiver(modelnumbernTXVR-250)hasanassociated
LED that provides status information and programming feedback. Additionally,
the Transceiver has a push-button that is used to interface with the unit. This
instructioncardprovidesinformationonhowtointerprettheLEDblinkpatterns,as
wellashowtousethepush-buttontoconguretheunit’swirelesscapabilities.
POWER UP
WhenpowerisrstappliedtoaTransceiver(orwhentheunitisreset),theLEDs
willashallONtogether,thenallOFFtogether.Thiswillrepeatseveraltimes.
INITIAL DEVICE DISCOVERY
When a new nLight device or a string of new nLight devices is plugged into a
port,thecorrespondingLEDwillcontinuouslyashquicklytoindicatethattheport
is in discovery mode. Discovery should be completed within a few seconds.To
force rediscovery,reset the Transceiver by pressing and holding the button for
6seconds.
NORMAL LED OPERATION
• Afterdiscoveryhasnished,theportLEDswilloperateinoneoftwomodes:
ActivityMode(default)orDeviceCountMode.
• Pressingthebuttononcetogglesbetweenthetwomodes.
• InActivityMode,eachportLED(inalternatingsequence)willregularlyblinkone
ofthefollowingstates:
 1 Blink=Portispollingconnectedzoneofdevices
 2 Blinks=PortiswiredtoanupstreamTransceiver/BridgeortheGateway
4 Blinks=PortiswiredtoaTransceiver/Bridgefurtherdownstreamfrom 
   theGateway
• InDeviceCountMode,eachportLED(inalternatingsequence)willindicatethe
numberofdetecteddevicesbyblinkingoutatwodigitnumber.
• Rapidblinkingindicatesthenumberzero.Ifthecountisgreaterthan99,threedigits
willbeblinkedinasimilarmanner.
• AportLEDthatdoesnotblink,orblinkserratically,indicatesabrokenormiswired
CAT-5connection.
*Note:ForusewithnLightwirelessdevicesonly
1
st
DIGIT(pause)2
nd
DIGIT