Discovery Gate Ethernet Demo Software Manual FCC ID: 2AVDNGC665017 Product code: U04 ETH 11 Product: Discovery Gate Ethernet Document Type: Demo Software Manual Document Rev. 0.1 Data 08/06/2020 Sensor ID s.r.l. c/o Sviluppo Italia Molise • Via don G. Mucciardi 5 • 86020 Campochiaro (CB) • Italy Tel./Fax: +39 0874.775257 • P.IVA 01614260709 • E-mail: info@sensorid.it • Web site: www.sensorid.
Summary 1 Hardware description ................................................................................................................... 4 2 Antenna power supply ................................................................................................................. 4 3 Access to Discovery Gate ............................................................................................................ 5 3.1 Login screen. ..............................................................
10 Federal Communications Commission (FCC) ........................................................................... 15 10.1 Part 15.19............................................................................................................................. 15 10.2 Part 15.21............................................................................................................................. 15 10.3 Part 15.105....................................................................................
1 Hardware description 2 Antenna power supply The antenna power supply is obtained through the PoE (Power over Ethernet ) according to IEEE 802.3af standard ( up to 15.4 W of DC power). Sensor ID s.r.l. c/o Sviluppo Italia Molise • Via don G. Mucciardi 5 • 86020 Campochiaro (CB) • Italy Tel./Fax: +39 0874.775257 • P.IVA 01614260709 • E-mail: info@sensorid.it • Web site: www.sensorid.
3 Access to Discovery Gate 3.1 Login screen. To access to the discovery gate login page, you must start your browser (preferably FireFox) and enter the following url in the address bar: http://discovery-(antenna mac address).local/ The specific address of antenna is attached on external box You can access the gate with user: admin and password: password2010 4 Home page The first page after authentication is: Sensor ID s.r.l. c/o Sviluppo Italia Molise • Via don G.
In this page it’s possible select one of the reader configuration or monitoring options. 5 Monitor In the monitor page the user can see the tags read with date and time of reading 6 Antenna setting In this page it’s possible read and set the reading configurations Sensor ID s.r.l. c/o Sviluppo Italia Molise • Via don G. Mucciardi 5 • 86020 Campochiaro (CB) • Italy Tel./Fax: +39 0874.775257 • P.IVA 01614260709 • E-mail: info@sensorid.it • Web site: www.sensorid.
6.1 Firmware/Hardware These fields show the firmware and hardware revision of UHF Reader 6.2 Power Using the power tab it’s possible increase or decrease the RF power emitted by the reader. In particular the maximum power is 10 and minimum is 1. After select the desired value, press confirm button to set it. 6.3 Distance The distance tab increase or decrease the reading distance. In particular the maximum distance is 10 and minimum is 1. After select the desired value, press confirm button to set it.
The maximum value is 24 and minimum is 2 according to the EPC standard. 6.5 User memory size This tab defines the number of byte to read in User memory. The maximum value is 64 and minimum is 2, and according to the EPC standard. 6.6 EPC Reading This tab enable or disable the reading of EPC memory of tags 6.7 TID Reading This tab enable or disable the reading of TID memory of tags 6.8 User Reading This tab enable or disable the reading of User memory of tags 6.
6.12 Buzzer Using this tab it’s possible activate or deactivate the sound emitted by the reader at every reading. 6.13 Antenna Tuning This tab performs the tuning of antenna. This command must be send only when the antenna is installed and seated correctly. Run the antenna tuning to optimize the reading distances. A good value of tuning is found when the last four characters are 00XX. Warning! A wrong setting may affect antenna performance.
8 Operative mode The Discovery Gate can operates in two mode: 1. Only monitor 2. Service Consumer When is selected “only monitor” no tag is sent to Server, this mode is for test only. Service Consumer mode is used for send data to a web service. Before doing this you need to configure some parameters in “web service” menu. Sensor ID s.r.l. c/o Sviluppo Italia Molise • Via don G. Mucciardi 5 • 86020 Campochiaro (CB) • Italy Tel./Fax: +39 0874.775257 • P.IVA 01614260709 • E-mail: info@sensorid.
9 Web Service On this page you can set the parameters for sending data to the webservice. First of all we must enter the URL of the endpoint of the webservice. Params in the url parameter you can use some parmeters placeolder for create dynamic …. $P{payload} : tag read form antenna $P{mac}: antenna mac address $P{timestamp} : timestamp Sensor ID s.r.l. c/o Sviluppo Italia Molise • Via don G. Mucciardi 5 • 86020 Campochiaro (CB) • Italy Tel./Fax: +39 0874.775257 • P.
$P{gate_id} : production id Request Method and authentication In this section is possible set the request method, POST or GET, and authorizzation credential for the basic authentication. You can customize the headers and body of request. The table below shows all the codes that you can pass to the timestamp format. Directive Meaning ts_seconds Unix Timestamp %a Abbreviated weekday name. Example Sun, Mon, ... Sensor ID s.r.l. c/o Sviluppo Italia Molise • Via don G.
Directive Meaning Example %A Full weekday name. Sunday, Monday, ... %w Weekday as a decimal number. 0, 1, ..., 6 %d Day of the month as a zero-padded decimal. 01, 02, ..., 31 %-d Day of the month as a decimal number. 1, 2, ..., 30 %b Abbreviated month name. Jan, Feb, ..., Dec %B Full month name. January, February, ... %m Month as a zero-padded decimal number. 01, 02, ..., 12 %-m Month as a decimal number. 1, 2, ..., 12 %y Year without century as a zero-padded decimal number.
Directive Meaning Example %U Week number of the year (Sunday as the first day of the week). All days 00, 01, ..., 53 in a new year preceding the first Sunday are considered to be in week 0. %W Week number of the year (Monday as the first day of the week). All days 00, 01, ..., 53 in a new year preceding the first Monday are considered to be in week 0. %c Locale’s appropriate date and time representation. Mon Sep 30 07:06:05 2013 %x Locale’s appropriate date representation.
10 Federal Communications Commission (FCC) 10.1 Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 10.2 Part 15.