SENSEON PLUS PROGRAMMING GUIDE TECHNICAL SPECIFICATIONS senseonsecure.
PROGRAMMING GUIDE Programming Instructions & Technical Specifications TABLE OF CONTENTS 1. Card Types ........................................................................................................ 3 2. Card Organization Checklist ........................................................................... 3 3. Before Programming....................................................................................... 4 A. Programming Tips ..............................................................
Card Types Your Proximity Reader is designed for two types of card access, Administrators and Users: MASTER ADMIN CARD Master Admin Card is the primary card for your Senseon system. It is the first card you will activate with your reader and the one that initiates the set up of other cards. Administrator Cards have programming rights, but can't unlock cabinets, drawers and doors. At this access level, you can add or delete User Cards and make changes to operational setings.
Before Programming Programming Tips Note: 1. The number of taps and beeps will vary according to each task! 2. Listen for 2 initial beeps after the first tapping of an Administrator Card. 3. Tap access cards as close as possible to your Proximity Reader. TAP Tap an Administrator Card to your reader the number of times required for each task. WAIT Wait 3 seconds and listen for the reader to beep the same number of times you tapped your Administrator Card.
Adding Cards A. New Administrator Cards Tap the Administrator Card 5 times at the designated Proximity Reader. Wait + Listen. Tap a Blank Card. 5 beeps will sound. Positive beep will sound. The Blank Card is now a new Administrator Card. Tap the Administrator Card to the proximity reader to exit. Or wait 15 seconds. To add another Administrator Card, tap an additional Blank Card once. The Reader will beep twice to verify every new Administrator Card added. B.
Deleting Cards D. Deleting All User + Admin Cards After deleting all User Cards, your Proximity Reader will auto-exit programming mode. This does not apply to Master Admin Card. Tap 9x Tap the Administrator Card. Wait 3sec And Listen. 9 beeps will sound. C. Delete Individual User Cards Tap12x Wait 30sec Positive Beep will sound. All User and Admin cards are now deleted. E.
System Adjustments - The Proximity Reader will automatically exit programming mode after 15 Seconds. G. Change Between Auto-Relock + Manual Lock Mode Tap 4x Wait 3sec Tap the Administrator Card. And Listen 4 beeps will sound. Wait 1sec Wait a second and the mode changes automatically. Positive Beep = Auto-Relock Mode Negantive Beep = Manual Lock Mode H. Adjust Sound Setting F. Adjusting Auto-Relock Time Tap 3x Tap 2x Tap the Administrator Card. Tap the Administrator Card.
J. Controller Light Indicator On/Off Tap 8x Tap the Administrator Card. I. Reader Light Indicator ON/OFF Wait 5sec And Listen 8 beeps will sound. Wait 1sec Positive Beep = Lights Enabled Negantive Beep = Lights Disabled K. Removing the Admin Card Tap 11x Tap 6x Tap the Administrator Card. Tap the Administrator Card. Wait 5sec Wait 5sec 11 beeps will sound. Wait 1sec Tap the Admin Card. 6 beeps will sound.
System Reset A system reset will delete all cards from the system. This includes all Administrator Cards and User Cards. Locate the Reset button on the side of your controller. With the controller powered on, use the pointed end of a paperclip or similar object to press and hold the Reset button for 6 seconds. Wait for the controller to fully reset and power back on. The controller light will start blinking blue. Note: We recommend that system resets are performed by a qualified Senseon technician.
FCC Statement FCC ID: 2AEDR-SPLUSPR-1 Model: SPLUSPR-1 Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
SENSEON PLUS PROGRAMMING GUIDE HANDHELD senseonsecure.
PROGRAMMING GUIDE TABLE OF CONTENTS 1. Introduction ....................................................................................................... 3 1. Managing Users ........................................................................................... 3 2. Audit Trail ..................................................................................................... 3 3. Advanced Settings ....................................................................................... 3 2.
1 Introduction The Senseon Plus Handheld Programmer streamlines the programming of your Senseon Plus system. The Handheld Programmer enables configuration of Senseon Plus system's advanced capabilities, notably: Discrete Access Dual Authorization Audit Trail Logs Touch-Screen Programming 1.1 Managing Users 1.2 Audit Trail The Programmer makes adding, modifying, and removing users easy and intuitive. On-screen prompts let you manage user permissions with ease.
2 Programmer Setup 2 Programmer Setup Make sure your SDHC Card is placed inside the Handheld Programmer’s slot for SD cards. Connect the Programmer to the Controller via the attached Magnetic Connect Cable. Your Programmer's screen will illuminate upon connection with the Controller. Magnetic Connect Cable 2.1 Authentication For security, only a user with an authenticated (scanned) Administrator Card can access the Senseon Plus Programming Mode. The opening screen will prompt you to “SCAN ADMIN CARD.” 2.
2.2B The EDIT button will take you to an “EDIT DATE AND TIME” screen. Dates adjust by month, day, and year. Times adjust by hour, minute, and second. Press SAVE when finished. Once set up, your Programmer will send you back to the home screen. 2.2C Your Programmer’s unique System Serial Number is on top. Below the System Serial Number, you will find three buttons: • MANAGE CARDS • AUDIT TRAIL • SETTINGS We’ll cover these buttons in Sections 4 through 8.
3 Administrator & User Description Senseon Plus cards can be programmed as either Administrator or User. 3.1 Administrator 3.2 User An Administrator can use the Handheld Programmer to program the system. An Administrator can determine a User’s level of access and adjust a system's settings. An Administrator can not access channels. A User has access to channels an Administrator has determined. This may be one or multiple channels.
4E 4F If you choose to create a User Card, you may choose one or more channels of access. Each channel corresponds to one or more openings. Press CONFIRM once you have determined your card’s level of access. 4G 4H This takes you to a screen labeled “SCAN CARD TO ADD.” Tap a blank card on your Senseon Plus Reader. After tapping your card, you will come to a screen labeled “ENTER ID FOR ADDED CARD.” 4I 4J If your card has a barcode, press SCAN BARCODE.
4K 4L Once you have entered an ID, press the in the lower left of the numbered pad to confirm. Once confirmed, a prompt labeled “Card Added” will appear. 4M If the card you tried to add is already in the system, you will receive a prompt labeled “ERROR: Card Not Added.” Either of the above prompts will take you back to the “SCAN CARD TO ADD” screen. From there you can continue to add cards.
5 Modifying Cards 5A 5B To modify a card, press MANAGE CARDS on your Programmer’s home screen. On the “MANAGE CARDS” screen, press SEARCH. 5C 5D This will take you to the “SEARCH FOR CARD” screen. From here, you can modify a card in three ways. Option 1. Press SCAN CARD, then tap the card you wish to modify at the Reader. 5E 5F Option 2. Press SCAN BARCODE, then scan your card’s barcode with your Programmer. Confirm with the press of the in the lower left of the numeric pad. Option 3.
5G 5H Once you’ve scanned or entered your card ID, you will receive a prompt with three buttons: This takes you to the “SELECT CARD ACCESS” channel screen. Select which channels you wish to modify for this card. • MODIFY • REMOVE • BACK Press MODIFY. 5I Press CONFIRM when finished to return you to the prior screen. 10 H ANDHELD PROG RA MMING G UIDE Each channel, labeled next to a box, corresponds to one or more cabinet openings. You can even turn a User Card into an Admin Card and vice-versa.
6 Removing a Card 6A 6B To remove a card, press MANAGE CARDS on your Programmer’s home screen. On the “MANAGE CARDS” screen, press SEARCH. 6C 6D This will take you to the “SEARCH FOR CARD” screen. From here, you can search for a card in three ways. Option 1. Press SCAN CARD, then tap the card you wish to modify on the Reader. 6E 6F Option 2. Press SCAN BARCODE, then scan your card’s barcode with your Programmer. Confirm with the press of the in the lower left of the numeric pad. Option 3.
6G Once you’ve scanned or input your card, you will receive a prompt with three buttons: • MODIFY • REMOVE • BACK Press REMOVE. This will remove the card from file and return you to the prior screen. 7 Audit Trail 7A 7B A Senseon Plus Controller stores your most most recent 15,000 audit trail transactions. You can download a list of these transactions by pressing AUDIT TRAIL on the home screen. Press the button “Download Audit Data” on the next screen.
8 System Settings 8A 8B You can access your system settings via the SETTINGS button on the home screen. This sends you to the “SYSTEM SETTINGS” menu where you shut off or modify features. 8C The SYSTEM SETTINGS menu has three screens. Use the < and > buttons to navigate between them. Next, we’ll explore the different settings on the menu.
8.1 Lock Mode 8.1A 8.1B Your Programmer enables you to choose from two lock modes. You can activate either mode by pressing the colored button next to the setting labeled “Lock Mode.” The TIMED setting activates a relock condition after a programmed amount of time. Press the underlined section labeled “Auto Relock Timing” to activate a prompt. 8.1C 8.1D A prompt allows you to adjust the time for your cabinet’s to auto relock. You can choose from 1 to 255 sec. Press OK when done.
8.2 Unsecure Warning 8.2A 8.2B This setting activates warning beeps when a cabinet remains open or unlocked past a programmed time. You can tap this setting ON or OFF. When ON, adjust the “Warn After” prompt to the amount of time you wish. You can adjust this warning to appear anywhere from 1 to 255 sec. after opening. 8.3 Delay to Open 8.4 Dual Authorization This setting activates a timed delay before your system unlocks a cabinet. You can adjust this delay to last anywhere from 1 to 255 sec. 8.
8.7 Sound 8.8 Lights This setting turns the Reader’s speaker ON or OFF. Note: The sound during system programming is always on. This setting lets you turn LED lights on your Controller or Reader on or off. 8.9 System Time This setting lets you edit time. Proper time is vital to ensuring accurate audit trail information. 8.10 Copy & Transfer These buttons enable you to copy and transfer your cards and settings information from one controller to another.
9 Exit Programming Mode To exit programming mode, disconnect the Programmer’s round Mag-Connect Cable from its counterpart. The system will return to normal operating mode.
senseonsecure.com Accuride International, Inc. Shoemaker Avenue Santa Fe Springs, CA 6 © Accuride International, Inc.