Instruction manual Digital 9000 System
Table Of Contents
- Digital_9000_Manual_06_2017_EN
- Important safety instructions
- Digital 9000 – System overview
- Delivery includes
- EM 9046 receiver
- EM 9046 CAB cable set
- Antennas and antenna boosters
- GZL 9000 antenna cables
- SKM 9000/SKM 9000 COM radio microphone
- Microphone heads for the SKM 9000 radio microphone
- SK 9000 bodypack transmitter
- Microphones for the SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- CI 1-4 line/instrument cable for the SK 9000 bodypack transmitter
- B 60/B 61 battery packs
- BA 60/BA 61 accupack
- L 60 charger
- Product overview
- EM 9046 receiver
- Antennas and antenna boosters
- GZL 9000 antenna cable
- SKM 9000/SKM 9000 COM radio microphone
- SK 9000 bodypack transmitter
- KA 9000 COM command adapter for the SK 9000 bodypack transmitter
- BA 60 accupack
- BA 61 accupack
- B 60 battery pack
- B 61 battery pack
- L 60 charger
- Preparing the EM 9046 receiver for use
- Preparing the A/AB/AD 9000 antennas and/or antenna boosters for use
- Preparing the SKM 9000 radio microphone for use
- Preparing the SK 9000 bodypack transmitter for use
- Preparing the L 60 charger for use
- Cascading several chargers
- Setting up or mounting the charger
- Preparing the Digital 9000 system for use
- Using the EM 9046
- Using the SKM 9000
- Using the SK 9000
- Using the L 60
- Cleaning and maintaining the Digital 9000 system
- If a problem occurs ...
- Specifications
Digital 9000 | 73
Using the EM 9046
If you have extended the EM 9046’s hardw
are configuration, this is dis-
played in the “hw setup” menu item with the status “added”:
In both cases, the “Press SET to confirm” button is highlighted in blue.
In the “hw setup” menu item, you confirm modifications as follows:
왘 Press the jog dial.
The “Press SET to confirm” button is framed in blue and “Press save to
confirm hw setup” appears in the menu selection.
왘 Press the button F.
“Firmware” – Displaying the hardware versions/firmware
versions and updating the firmware
If you update the EM 9046 receiver’s firmware using the WSM software,
the current firmware versions of the 9000 series boosters and transmit-
ters are also stored on the receiver.
Via the “Firmware” menu item, you can display the firmware versions of
the receiver, the boosters and the transmitters and update the firmware
of the boosters and the transmitters.
The currently installed firmware version of the EM 9046 is displayed in the
menu selection (see above).
p
Slot Module Type State
RX1 EM 9046 DRX ok
RX2 EM 9046 DRX ok
RX3 EM 9046 DRX ok
RX4 EM 9046 DRX ok
RX5 EM 9046 DRX ok
RX6 EM 9046 DRX ok
RX7 EM 9046 DRX ok
RX8 EM 9046 DRX ok
OUT1 EM 9046 AAO ok
OUT2 EM 9046 DAO added
EM9046_2_3_1_12345
firmware
Update to rmware:
Antenna booster
10-11-30-11
RF IN A:
Firmware:
AB9000_2
10-08-10-10
RF IN B:
Firmware:
AB9000_2
10-08-10-10
Start update
Transmitter
SCAN MODE
Transmitter:
Firmware:
New rmware